Enterasys RoamAbout® RBT-4102, RBT-4102-BG, RBT-4102C, RBT-4102C-EU, and RBT-4102-EU Wireless Access Point Installation Guide P/N 9034148-16
NOTICE ELECTRICAL HAZARD: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. ENTERASYS NETWORKS reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice.
Compliances COMPLIANCES RBT-4102, RBT-4102-BG, and RBT-4102-EU Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Wireless 5 GHz Band Statements: As the Access Point can operate in the 5150-5250 MHz frequency band it is limited by the FCC, Industry Canada and some other countries to indoor use only so as to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users (meaning they have priority) of the 5250-5350 MHz and 5650-5850 MHz bands. These radars could cause interference and /or damage to the access point when used in Canada.
Compliances 003NY05152 003GZ05053 003WY05076 003UX05009 EC Conformance Declaration Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: • • • • EN 60950 (IEC 60950) - Product Safety EN 301 893 - Technical requirements for 5 GHz radio equipment EN 300 328 - Technical requirements for 2.
Operation Using 5 GHz Channels in the European Community The user/installer must use the provided configuration utility to check the current channel of operation and make necessary configuration changes to ensure operation occurs in conformance with European National spectrum usage laws as described below and elsewhere in this document. Allowed 5GHz Channels in Each European Community Country Allowed Frequency Bands Allowed Channel Numbers Countries 5.15 - 5.35* & 5.470 - 5.
Compliances • The 5 GHz Turbo Mode feature is not allowed for operation in any of the countries. The current setting for this feature is found in the 5 GHz 802.11a Radio Settings Window as described in the user guide. • The 5 GHz radio's Auto Channel Select setting described in the user guide must always remain enabled to ensure that automatic 5 GHz channel selection complies with requirements. The current setting for this feature is found in the 5 GHz 802.
RBT-4102C and RBT-4102C-EU Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Compliances Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur: “Appareils Numériques,” NMB-003 édictée par l’Industrie.
Countries of Operation & Conditions of Use in the European Community This device is intended to be operated in all countries of the European Community. Requirements for indoor vs. outdoor operation, license requirements and allowed channels of operation apply in some countries as described below: Note: The user must use the configuration utility provided with this product to ensure the channels of operation are in conformance with the spectrum usage rules for European Community countries as described below.
Compliances Operation Using 5 GHz Channels in the European Community The user/installer must use the provided configuration utility to check the current channel of operation and make necessary configuration changes to ensure operation occurs in conformance with European National spectrum usage laws as described below and elsewhere in this document. Allowed 5GHz Channels in Each European Community Country Allowed Frequency Bands 5.15 - 5.
remain enabled to ensure that automatic 5 GHz channel selection complies with requirements. The current setting for this feature is found in the 5 GHz 802.11a Radio Settings Window as described in the user guide. • This device is restricted to indoor use when operated using the 5.15 - 5.25 GHz band: Channels 36, 40, 44, 48.
Compliances DECLARATION OF CONFORMITY IN LANGUAGES OF THE EUROPEAN COMMUNITY English Hereby, Enterasys, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/ EC. A copy of the original Declaration of conformity can be obtained from Enterasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA.
Greek (GR) με την παρουσα Enterasys δηλωνει οτι radio LAN device συμμορφωνεται προσ τισ ουσιωδεισ απαιτησεισ και τισ λοιπεσ σΧετικεσ διαταξεισ τησ οδηγιασ 1999/5/εκ. Ένα αντίγραφο της αρχικής ∆ιακήρυξης της συμμόρφωσης μπορεί να ληφθεί από Enterasys Networks, 50 Minuteman Road, Andover, Ma 01810, USA. Italian (IT) Con la presente Enterasys dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Compliances SAFETY COMPLIANCE Power Cord Safety Please read the following safety information carefully before installing the access point: WARNING: Installation and removal of the unit must be carried out by qualified personnel only. • The unit must be connected to an earthed (grounded) outlet to comply with international safety standards. • Do not connect the unit to an A.C. outlet (power supply) without an earth (ground) connection.
Power Cord Set Europe The supply plug must comply with CEE7/7 (“SCHUKO”). The mains cord must be or marked and be of type HO3VVF3GO.75 (minimum). IEC-320 receptacle.
Compliances HAZARDOUS SUBSTANCES This product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment EUROPEAN WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) NOTICE In accordance with Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment (WEEE): 1.
ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc.
Compliances 3. 4. derivative works based on the Program, in whole or in part. (iii) Publish, disclose, copy, reproduce or transmit the Program, in whole or in part. (iv) Assign, sell, license, sublicense, rent, lease, encumber by way of security interest, pledge or otherwise transfer the Program, in whole or in part. (v) Remove any copyright, trademark, proprietary rights, disclaimer or warning notice included on or embedded in any part of the Program. APPLICABLE LAW.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Program (i) was developed solely at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data belonging to Enterasys and/or its suppliers.
Compliances 8. AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii) the use, copying and deployment of the Program.
13. SEVERABILITY. In the event any provision of this Agreement is found to be invalid, illegal or unenforceable, the validity, legality and enforceability of any of the remaining provisions shall not in any way be affected or impaired thereby, and that provision shall be reformed, construed and enforced to the maximum extent permissible. Any such invalidity, illegality or unenforceability in any jurisdiction shall not invalidate or render illegal or unenforceable such provision in any other jurisdiction.
Compliances xxii
Table of Contents Preface Purpose..................................................................................................................xxv Intended Audience .................................................................................................xxv Associated Documents ..........................................................................................xxv Getting Help ..........................................................................................................
Contents Wiring Map for Serial Cable ..........................................................................B-4 Appendix C: Specifications General Specifications .................................................................................... C-1 Maximum Channels ..................................................................................... C-1 Data Rate ..................................................................................................... C-1 Modulation Type ...................
Preface Purpose This manual provides the specifications and the installation instructions for the RoamAbout RBT-4102, RBT-4102C, RBT-4102C-EU, and the RBT-4102-EU Wireless Access Points. It also includes the basic configuration information using Web management, and the Command Line Interface (CLI). Note: The RBT-4102C-EU, although listed in this document, is not available until March 2008.
Getting Help For additional support related to this device or document, contact Enterasys Networks using one of the following methods. World Wide Web: http://www.enterasys.com/services/support Phone: 1-800-872-8440 (toll-free in the U.S. and Canada) or 1-978-684-1000 For the Enterasys Networks Support toll-free number in your country: http://www.enterasys.com/services/support/contact Email: support@enterasys.com To expedite your message, please type [RoamAbout] in the subject line.
Chapter 1: Introduction Note: The RBT-4102C-EU, although listed in this document, is not available until March 2008. The RoamAbout RBT-4102, RBT-4102-BG, RBT-4102C, RBT-4102C-EU, and the RBT-4102-EU are IEEE 802.11a/b/g access points that provide transparent, wireless high-speed data communications between the wired LAN and fixed or mobile devices equipped with an 802.11a (not RBT-4102-BG), 802.11b, or 802.11g wireless adapter.
Introduction Package Checklist The RoamAbout package includes: • One RoamAbout access point • One RS-232 console cable • One AC power adapter and power cord • Four rubber feet • Three wall-mounting screws • Bezel • Mounting bracket • Documentation CD (includes this document). Please go to http://www.enterasys.com to ensure that you have the latest documentation. Inform your dealer if there are any incorrect, missing or damaged parts. If possible, retain the carton, including the original packing materials.
Hardware Description Rear Panel External Antenna Connector (802.11a) Radio DC Power Supply RJ-45 Port, PoE Connector Reset Button Console Port Security Slot External Antenna Connector (802.
Introduction Component Description Antennas The access point includes integrated diversity antennas for wireless communications. A diversity antenna system uses two identical antennas to receive and transmit signals, helping to avoid multipath fading effects. When receiving, the access point checks both antennas and selects the one with the strongest signal. When transmitting, it will continue to use the antenna previously selected for receiving.
Hardware Description LED Status Description Power On Green Indicates that the system is working normally. Flashing Green Indicates: • running a self-test. • loading software program. Ethernet Link Wireless Link Wireless Link On Amber Indicates a CPU or system failure. Flashing Amber (Prolonged) Indicates system errors. On Green Indicates a valid 10/100 Mbps Ethernet cable link. Flashing Green Indicates that the access point is transmitting or receiving data on a 10/100 Mbps Ethernet LAN.
Introduction Ethernet Port The access point has one 10BASE-T/100BASE-TX RJ-45 port that can be attached directly to 10BASE-T/100BASE-TX LAN segments. These segments must conform to the IEEE 802.3 or 802.3u specifications. This port supports automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs, switches, or hubs.
Hardware Description Reset Button This button is used to reset the access point or restore the factory default configuration. If you hold down the button for less than 5 seconds, the access point will perform a hardware reset. If you hold down the button for 5 seconds or more, any configuration changes you may have made are removed, and the factory default configuration is restored to the access point. Power Connector The access point does not have a power switch.
Introduction 1-8
Chapter 2: Hardware Installation To install the access point, follow the steps outlined below: 1. Select a Site – Choose a proper place for the access point. In general, the best location is at the center of your wireless coverage area, within line of sight of all wireless devices. Try to place the access point in a position that can best cover its Basic Service Set (refer to “Infrastructure Wireless LAN” on page 4-3).
Hardware Installation • Using the mounting bracket, mark the position of the four screw holes on the wall or ceiling. For concrete or brick walls, you will need to drill holes and insert wall plugs for the screws. • Position the mounting bracket over the wall or ceiling screw holes, then insert the included screws and tighten them down to secure the bracket firmly to the wall or ceiling. • Attach the access point to the mounting bracket.
3. Lock the Access Point in Place – To prevent unauthorized removal of the access point, you can use a Kensington Slim MicroSaver security cable (not included) to attach the access point to a fixed object. 4. Connect the Power Cord – Connect the power adapter to the access point, and the power cord to an AC power outlet. Otherwise, the access point can derive its operating power directly from the RJ-45 port when connected to a device that provides IEEE 802.3af compliant Power over Ethernet (PoE).
Hardware Installation 2-4
Chapter 3: Access Point Configuration This chapter describes how to use the Web interface to perform initial configuration of the access point. You can manage the RoamAbout Access Point 4102 with: • The Command Line Interface (CLI) accessed through a direct connection to the console port. Refer to the RoamAbout RBT-4102 Wireless Access Point Configuration Guide to view a complete list of all of the CLI commands, and how to use them. • The web interface accessed through a web browser (Internet Explorer V5.
Access Point Configuration • Set the emulation mode to VT100. • When using HyperTerminal, select Terminal keys, not Windows keys. Note: When using HyperTerminal with Microsoft® Windows® 2000, make sure that you have Windows 2000 Service Pack 2 or later installed. Windows 2000 Service Pack 2 fixes the problem of arrow keys not functioning in HyperTerminal’s VT100 emulation. Go to www.microsoft.com for information on Windows 2000 service packs. 4.
Using the CLI a. Enter country ? to display the list of countries.
Access Point Configuration c. Enter no ip dhcp to disable DHCP. RoamAbout 4102(if-ethernet)#no ip dhcp DHCP client state has changed. Please reset AP for change to take effect. RoamAbout 4102(if-ethernet)#exit RoamAbout 4102#reset board Reboot system now? : y Username: admin Password:******** RoamAbout 4102#configure Enter configuration commands, one per line. End with CTRL/Z RoamAbout 4102(config)#interface ethernet Enter Ethernet configuration commands, one per line. RoamAbout 4102(if-ethernet)# d.
Using the CLI 5. Specify the management VLAN ID for the access point: The management VLAN is for managing the access point. For example, the access point allows traffic that is tagged with the specified VLAN to manage the access point via remote management, SSH, SNMP, Telnet, and so forth. VLAN management is enabled by default, and cannot be disabled. Note: You must set up the network switch port to support tagged VLAN packets from the access point.
Access Point Configuration Using Web Management Notes: • The default username is admin, and the default password is password. • To get help, click on Help, located at the bottom of the screen. • You must click on the Apply button, located at the bottom of the each Web interface page for the configuration to take effect. To use the Web interface to minimally configure the access point, follow these steps: 1.
Using Web Management 2. Enter the default username admin and the default password password, and click LOGIN. • If applicable, the Country Code page appears, go to step 3. • If the Country Code page does not appear, go to step 4. 3. If applicable, set the Country Code: a. Click the arrow in the Country pull-down menu to select the appropriate country, then click Apply at the bottom of the page. b. Click Administration from the menu on the left-hand side of the page. The Administration page appears.
Access Point Configuration c. Click the Reset button next to Reset Access Point, located at the bottom of the page. The access point prompts you to confirm that you want to reboot the system. d. Click OK. The access point reboots, and the Login window appears. e. Enter the username admin and the password password, and click LOGIN. The Identification page appears.
Using Web Management f. 4. Go to step 4. Enter the following information, and click Apply. • System Name is an alias used for the access point, enabling the device to be uniquely identified on the network. Default: RoamAbout AP. Length: 1 to 22 characters • System Location is a text string that describes the system location. Maximum length: 253 characters • System Contact is a text string that describes the system contact. Maximum length: 253 characters The access point displays a Settings Saved message.
Access Point Configuration b. Click the DHCP Client: Disable radio button. DHCP allows you to enable or disable the option to obtain the IP settings for the access point from a DHCP (Dynamic Host Configuration Protocol) server. The IP address, subnet mask, default gateway, and Domain Name Server (DNS) address are dynamically assigned to the access point by the network DHCP server. Default: Enable c. Enter the IP Address, Subnet Mask, Default Gateway, and Primary and Secondary DNS.
Using Web Management • Default Gateway is the IP address of the router for the access point, which is used if the requested destination address is not on the local subnet. If you have management stations, DNS, RADIUS, or other network servers located on another subnet, type the IP address of the default gateway router in the text field provided. Otherwise, leave the address as all zeros (0.0.0.0). d. Click Apply at the bottom of the page. A Settings Saved message appears on the screen. e. Click OK. f.
Access Point Configuration 6. To change the username and password. a. Click Administration from the menu on the left hand side of the page. The Administration page appears. b. Specify a new username in the Username field. c. Specify a new password in the Password field. d. Specify the new password again in the Confirm Password field. e. Click Apply at the bottom of the page.
Using Web Management The access point displays a Settings Saved message. f. 7. Click OK. To specify the management VLAN ID: a. Click Filter Control from the menu. The Filter Control page appears.
Access Point Configuration b. Click the Management VLAN ID: field and enter the VLAN ID from which you will manage the AP. The management VLAN is for managing the access point. For example, the access point allows traffic that is tagged with the specified VLAN to manage the access point via remote management, SSH, SNMP, Telnet, and so forth. VLAN management is enabled by default, and cannot be disabled. Note: c. 8.
Chapter 4: Network Configuration Wireless networks support a standalone configuration as well as an integrated configuration with 10/100 Mbps Ethernet LANs. The RoamAbout RBT-4102 also provides bridging services that can be configured independently on either the 5 GHz or 2.4 GHz radio interfaces.
Network Configuration Network Topologies Ad Hoc Wireless LAN (no Access Point) An ad hoc wireless LAN consists of a group of computers, each equipped with a wireless adapter, connected via radio signals as an independent wireless LAN. Computers in a specific ad hoc wireless LAN must therefore be configured to the same radio channel. An ad hoc wireless LAN can be used for a branch office or SOHO operation.
Network Topologies Infrastructure Wireless LAN The access point also provides access to a wired LAN for wireless workstations. An integrated wired/wireless LAN is called an Infrastructure configuration. A Basic Service Set (BSS) consists of a group of wireless PC users, and an access point that is directly connected to the wired LAN.
Network Configuration Infrastructure Wireless LAN for Roaming Wireless PCs The Basic Service Set (BSS) defines the communications domain for each access point and its associated wireless clients. The BSS ID is a 48-bit binary number based on the access point’s wireless MAC address, and is set automatically and transparently as clients associate with the access point. The BSS ID is used in frames sent between the access point and its clients to identify traffic in the service area.
Network Topologies Infrastructure Wireless Bridge The IEEE 802.11 standard defines a Wireless Distribution System (WDS) for bridge connections between BSS areas (access points). The access point uses WDS to forward traffic on links between units. The access point supports WDS bridge links on either the 5 GHz (802.11a) or 2.4 GHz (802.11b/g) bands, and can be used with various external antennas to offer flexible deployment options.
Network Configuration 4-6
Appendix A: Troubleshooting Diagnosing Access Point Indicators Troubleshooting Chart Symptom Action Power LED is Off • AC power adapter may be disconnected. Check connections between the access point, the power adapter, and the wall outlet. • PoE power to the access point may be disabled at the connected switch port. Check the switch configuration to be sure that PoE power is enabled for the switch and specified port.
Troubleshooting A-2
Appendix B: Cables and Pinouts Twisted-Pair Cable Assignments For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable. Caution: DO NOT plug a phone jack connector into the RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards.
Cables and Pinouts 10/100BASE-TX Pin Assignments Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Category 3 or better cable for 10 Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet). The RJ-45 port on the access point supports automatic MDI/MDI-X operation, so you can use straight-through or crossover cables for all network connections to PCs, switches, or hubs.
Twisted-Pair Cable Assignments Straight-Through Wiring If the twisted-pair cable is to join two ports and only one of the ports has an internal crossover (MDI-X), the two pairs of wires must be straight-through.
Cables and Pinouts Console Port Pin Assignments The DB-9 console port on the front panel of the access point is used to connect to the access point for out-of-band console configuration. The command-line configuration program can be accessed from a terminal, or a PC running a terminal emulation program. The pin assignments and cable wiring used to connect to the console port are provided in the following table.
Appendix C: Specifications Note: The RBT-4102C-EU, although listed in this document, is not available until March 2008. General Specifications Maximum Channels 802.11a RBT-4102 US & Canada: 13 (normal mode), 5 (turbo mode) RBT-4102C US & Canada: 9 (normal mode), 5 (turbo mode) RBT-4102C-EU ETSI: 4 channels (normal mode) Japan: 8 channels (normal mode) RBT-4102-EU ETSI: 19 channels (normal mode) Japan: 15 channels (normal mode) 802.
Specifications Modulation Type 802.11a: BPSK, QPSK, 16-QAM, 64-QAM 802.11g: CCK, BPSK, QPSK, OFDM 802.11b: CCK, BPSK, QPSK Network Configuration Infrastructure Operating Frequency 802.11a: RBT-4102, RBT-4102-BG, RBT-4102-EU: 5.15 ~ 5.35 GHz US/Canada, Europe, Japan 5.470 ~ 5.725 GHz (Europe) 5.725 ~ 5.825 GHz US/Canada 4.92 ~ 4.98 GHz Japan 5.04 ~ 5.08 GHz Japan RBT-4102C, RBT-4102C-EU: 5.15 ~ 5.25 GHz US/Canada, Europe, Japan 5.25 ~ 5.35 GHz Japan 5.725 ~ 5.825 GHz US/Canada 4.92 ~ 4.98 GHz Japan 5.
General Specifications Physical Size 21.83 x 13.73 x 3.27 cm (8.60 x 5.40 x 1.29 in) Weight 0.687 kg (1.
Specifications Compliances RBT-4102, RBT-4102-BG, RBT-4102C FCC Class B (US) ICES-003 (Canada) RBT-4102C-EU, RBT-4102-EU RTTED 1999/5/EC ARB STD-T70, ARB STD-66, RCR STD-33, ARB STD-T71 (Japan) EN60601-1-2 Radio Signal Certification RBT-4102, RBT-4102-BG, RBT-4102-EU FCC Part 15C 15.247, 15.207 (2.4 GHz) FCC Part 15E 15.407 (5 GHz) RSS-210 (Canada) RBT-4102C, RBT-4102C-EU EN55022:1998, EN55024:1998, EN61000-3-2:2000, EN61000-3-3:1995, EN 301.893, EN 300.328, EN 301.489-1, EN 301.
Sensitivity Sensitivity IEEE 802.11a Sensitivity (GHz - dBm) Modulation/Rates 5.15-5.250 5.25-5.350 5.50-5.700 5.725-5.825 BPSK (6 Mbps) -88 -88 -88 -88 BPSK (9 Mbps) -87 -87 -87 -87 QPSK (12 Mbps) -86 -86 -86 -86 QPSK (18 Mbps) -83 -83 -83 -83 16 QAM (24 Mbps) -80 -80 -80 -80 16 QAM (36 Mbps) -76 -76 -76 -76 64 QAM (48 Mbps) -73 -73 -73 -73 64 QAM(54 Mbps) -70 -70 -70 -70 IEEE 802.
Specifications Transmit Power IEEE 802.11a Maximum Output Power (GHz - dBm) Data Rate 5.15-5.250 5.25-5.350 5.50-5.700 5.725-5.825 6 Mbps 20 20 20 19 9 Mbps 20 20 20 19 12 Mbps 20 20 20 19 18 Mbps 20 20 20 19 24 Mbps 20 20 20 19 36 Mbps 20 20 19 19 48 Mbps 19 19 18 18 54 Mbps 18 18 17 16 IEEE 802.11g Maximum Output Power (GHz - dBm) Data Rate 2.412 2.417~2.467 2.
Operating Range Operating Range The operating range distances listed in the following tables are for typical environments only. Operating ranges can vary considerably depending on factors such as local interference and barrier composition. It is recommended to do a site survey to determine the maximum ranges for specific access point locations in your environment. Note: 802.
Specifications External Antennas The RBT-4102, RBT-4102-BG, and the RBT-4102C are certified by the FCC, for use in the United States, to operate with these antennas: Note: High gain point to point antenna, model RBTES-AH-P23M (Gain 23 dBi), is certified under specific point to point condition and the use of point to multipoint systems, omnidirectional applications, and multiple co-related intentional radiators transmitting the same information is prohibited.
External Antennas Japan External Antenna Configurations Antenna Model Antenna Type Antenna Gain RBT4K-AG-IA 2.4–2.5 GHz Omnidirectional Indoor Range Extender 1 dBi with 8 ft. cable 5.15-5.35 GHz Omnidirectional Indoor Range Extender 5.725–5.825 GHz Omnidirectional Indoor Range Extender RBTES-BG-M08M 2.4–2.5 GHz Omnidirectional, outdoor 8 dBi RBTES-BG-S1490M 2.4–2.5 GHz Sector Panel, outdoor 14 dBi/90° RBTES-BG-P18M 2.4-2.
Specifications C-10
Index A E antennas, positioning 2-3 Ethernet cable 2-3 port 1-6 B Basic Service Set See BSS BSS 4-3 C G Gateway address 3-11 cable assignments B-1 change username and password 3-4 channels, maximum C-1 CLI change username and password 3-4 country code configuring 3-2 default username and password 3-2 disable DHCP 3-4 Gateway address 3-4 IP address configuring 3-4 logging in 3-2 VLAN management 3-5 console port 1-5 connecting 2-3 pin assignments B-4 country codes 3-3 CSMA/CA 1-1 I D O data rate, o
power connection 2-3 Power over Ethernet See PoE power supply, specifications C-2 R reset button 1-7 S set username and password web management 3-12 specifications C-1 subnet mask 3-10 system location 3-9 length 3-9 system name 3-9 length 3-9 T troubleshooting A-1 U using the CLI 3-1 V VLAN management web management 3-13 W web management 3-6 country code 3-7 logging in 3-6 set static address 3-9 set username and password 3-12 system information 3-9 VLAN managment 3-13 Index-2
