User Guide
Table Of Contents
- Information resources for the SP75 Printer
- About the printer
- Loading cards
- Loading print ribbon
- Loading laminator supply material
- Status light
- Check the PC connection
- Power on the printer
- The LCD panel
- Opening Properties or Printing Preferences
- Open the Printer Toolbox
- Cleaning the printer
- Getting the most out of your printer
- Printer supplies
- Printer Installation
- Printer LCD settings
- View status settings
- Change settings
- Run diagnostics commands
- Troubleshooting
- Site requirements
- Printer messages
- DM-00760 Duplex Error
- DM-00762 Duplex Jam
- DM-00767 Duplex Jam
- DM-00768 Lower Duplex Jam
- DM-00769 Lower Duplex Error
- DM-00770 Lower Duplex Jam
- IS-01206 No Card Picked
- SY-01305 Data Error
- SY-01306 Data Error
- SY-01310 Flash Error
- SY-01314 Flash Error
- SY-01317 Memory Error
- SY-01325 Data Error
- SY-01327 Data Error
- SY-01331 Comm Error
- SY-01332 Hardware Error
- MS-01401, MS-01402, MS-01403 Mag Stripe Data
- MS-01404, MS-01405, MS-01406 Mag Stripe Error
- MS-01407, MS-01408, or MS-01409 Mag Stripe Error
- MS-01410 Mag Stripe Error
- MS-01413 Mag Stripe Error
- MS-01417, MS-01418, MS-01419, MS-01420, MS-01421 Card Jam
- MS-01424 Mag Stripe Error
- MS-01425 Mag Stripe Error
- MS-01426 EEPROM Error
- MS-01427 Mag Stripe Error
- MS-01429 Mag Stripe Data
- MS-01430 Mag Stripe Error
- MS-01431 EEPROM Error
- MS-01435 No Mag Stripe
- OP-01604, OP-01654 L1 or L2 Heater Error
- OP-01611, OP-01661 Roller Error
- OP-01612, OP-01662 Card Jam
- OP-01613, OP-01663 L1 or L2 Supply Error
- OP-01614, OP-01664 Supply Break
- OP-01615, OP1665 L1 or L2 Supply Out
- OP-01616 Lam EEPROM Error
- OP-01619 Comm Error
- OP-01620 Wait for Temp
- OP-01621, OP-01671 Supply Low
- OP-01622, OP-01672 Supply Error
- OP-01623 Lam Hardware Error
- OP-01624, OP-01674 Card Jam
- OP-01651 No L2 Laminator
- PR-01703 Printhead Error
- PR-01705, PR-01706 Card Jam
- PR-01710 EEPROM Error
- PR-01715 Cover Open
- PR-01718 Printhead Temp
- PR-01719 Printhead Error
- PR-01720 Ribbon Error
- PR-01721 EEPROM Error
- PR-01723 Hardware Error
- PR-01724 Ribbon Break
- PR-01726 Ribbon Out
- PR-01730 Printhead Error
- PR-01737 Ribbon Low
- PR-01738 Ribbon Error
- SC-01804 No Smart Card
- Legal Notices (FCC)
Page 23
Getting the most out of your printer
To get the best quality cards and to maintain printer performance, follow these tips for success:
• Use the best quality cards available with a smooth, glossy PVC surface and print them only
once. Make sure options, such as a signature panel or a magnetic stripe, are high quality.
• Match the card design and the supplies you use to obtain the results you want.
— Edge to edge printing requires high-quality cards and can require fine-tuning the printer
(using the Smart Driver) and the card design (using ID software).
— Avoid placing an image or important data on the other side of the card from a magnetic
stripe, smart card chip, or signature panel.
— Locate bar codes at least 0.25 inches from other printing and from the edge of the card.
Make sure the color used to print the bar code works in your bar code readers.
— Do not print closer than 0.1 inch from a signature panel, magnetic stripe, or smart card
chip. Obtain information from your card manufacturer about card features and placing
design elements on the card.
— Do not apply topcoat or a patch over a magnetic stripe, signature panel, or smart card
chip. Patch material for use with a magnetic stripe or smart card is available.
— Do not apply topcoat or patch material in a laminator over topcoat applied using print
ribbon.
— Use cards without curled or raised edges when applying topcoat or patch material
using a laminator.