User Guide
Table Of Contents
- Information resources for the SP75 Printer
- About the printer
- Loading cards
- Loading print ribbon
- Loading laminator supply material
- Status light
- Check the PC connection
- Power on the printer
- The LCD panel
- Opening Properties or Printing Preferences
- Open the Printer Toolbox
- Cleaning the printer
- Getting the most out of your printer
- Printer supplies
- Printer Installation
- Printer LCD settings
- View status settings
- Change settings
- Run diagnostics commands
- Troubleshooting
- Site requirements
- Printer messages
- DM-00760 Duplex Error
- DM-00762 Duplex Jam
- DM-00767 Duplex Jam
- DM-00768 Lower Duplex Jam
- DM-00769 Lower Duplex Error
- DM-00770 Lower Duplex Jam
- IS-01206 No Card Picked
- SY-01305 Data Error
- SY-01306 Data Error
- SY-01310 Flash Error
- SY-01314 Flash Error
- SY-01317 Memory Error
- SY-01325 Data Error
- SY-01327 Data Error
- SY-01331 Comm Error
- SY-01332 Hardware Error
- MS-01401, MS-01402, MS-01403 Mag Stripe Data
- MS-01404, MS-01405, MS-01406 Mag Stripe Error
- MS-01407, MS-01408, or MS-01409 Mag Stripe Error
- MS-01410 Mag Stripe Error
- MS-01413 Mag Stripe Error
- MS-01417, MS-01418, MS-01419, MS-01420, MS-01421 Card Jam
- MS-01424 Mag Stripe Error
- MS-01425 Mag Stripe Error
- MS-01426 EEPROM Error
- MS-01427 Mag Stripe Error
- MS-01429 Mag Stripe Data
- MS-01430 Mag Stripe Error
- MS-01431 EEPROM Error
- MS-01435 No Mag Stripe
- OP-01604, OP-01654 L1 or L2 Heater Error
- OP-01611, OP-01661 Roller Error
- OP-01612, OP-01662 Card Jam
- OP-01613, OP-01663 L1 or L2 Supply Error
- OP-01614, OP-01664 Supply Break
- OP-01615, OP1665 L1 or L2 Supply Out
- OP-01616 Lam EEPROM Error
- OP-01619 Comm Error
- OP-01620 Wait for Temp
- OP-01621, OP-01671 Supply Low
- OP-01622, OP-01672 Supply Error
- OP-01623 Lam Hardware Error
- OP-01624, OP-01674 Card Jam
- OP-01651 No L2 Laminator
- PR-01703 Printhead Error
- PR-01705, PR-01706 Card Jam
- PR-01710 EEPROM Error
- PR-01715 Cover Open
- PR-01718 Printhead Temp
- PR-01719 Printhead Error
- PR-01720 Ribbon Error
- PR-01721 EEPROM Error
- PR-01723 Hardware Error
- PR-01724 Ribbon Break
- PR-01726 Ribbon Out
- PR-01730 Printhead Error
- PR-01737 Ribbon Low
- PR-01738 Ribbon Error
- SC-01804 No Smart Card
- Legal Notices (FCC)
Page 47
Run a laminator cleaning card
Tips for Success
• Run a laminator cleaning card only to remove particles of holographic or clear topcoat. If you do not use
topcoat material in your printer, you do not need to run a laminator cleaning card.
• The laminator cleaning card has adhesive on both sides; it is different from the printer cleaning card. See
Cleaning the Laminator in SP Series Info Central for more information.
1 With “Diagnostics” displayed on line 1, press the Up or Down Arrow key if needed
to display “Lam Clean Card” on line 2.
2 Remove the protective paper from both sides of the card.
3 Press the Enter key to start the cleaning routine. The Ready light blinks green.
4 Place the card in the output hopper as shown.