User's Guide
Table Of Contents
- Entrust Datacard CR805 Retransfer Card Printer User's Guide
- Table of Contents
- Chapter 1: Introduction
- Chapter 2: About the Printer
- Chapter 3: Using the Printer
- Chapter 4: Print Cards
- Chapter 5: System Maintenance
- Chapter 6: Troubleshooting
- Locate a Problem Within the Card Production System
- Locate a Problem with Basic Printer Functions
- Installation Problems
- Card Printer Driver Problems
- Card Appearance
- Magnetic Stripe Troubleshooting
- Laminator Troubleshooting
- Advanced Troubleshooting Tools
- Printer Card Jams
- Repair a Broken Ink Ribbon or Retransfer Film
- Messages and Conditions
- Respond to Messages
- Printer Messages
- Close and lock doors
- 100: Request not supported
- 103: Printer problem
- 104: Critical problem
- 105: Magstripe data error
- 106: Magstripe data not found
- 107: Magstripe read data error
- 108: Magstripe read no data
- 111: Card not picked
- 112: Card hopper empty
- 113: Close cover to continue
- 114: Cover opened during job
- 116: Magstripe not available
- 117: Reader not available
- 120: User paused the printer
- 122: Magstripe format problem
- 149: Option not installed
- 150: Print while unlocked
- 151: Failed to lock
- 152: Insert new card side 2 up
- 153: Insert same card side 2 up
- 166: C2 supply out or missing
- 167: C2 supply not identified
- 168: C2 supply not supported
- 170: Insert new card side 1 up
- 171: Insert same card side 1 up
- 172: Insert cleaning card
- 173: Improper shutdown
- 175: C2 supply error
- 176: C2 supply type error
- 228: C1 printhead error
- 229: C2 heat sensor error
- 230: C2 heater error
- 231: C2 heated roller motion error
- 232: Retransfer debow error
- 233: Smart card contact fail
- 234: K1 transport card jam
- 235: K2 transport card jam
- 236: Flipper module rotate error
- 237: C1 supply out or missing
- 238: C1 supply not identified
- 239: C1 supply not supported
- 240: C1 supply error
- 241: C1 supply type error
- 242: RT1 reject tray full
- 243: Card lost
- 245: Configuration error
- 275: Multi-hopper error
- 276: Multi-hopper card jam
- 277: Multi-hopper pick error
- 278: Insert cleaning card in H2
- Laminator Messages
- 177: Laminator not available
- 196: Laminator error critical
- 197: Laminator entry card problem
- 198: L1 area card problem
- 199: L2 area card problem
- 200: Laminator exit card problem
- 201: L1 supply problem
- 202: L1 supply out or missing
- 203: L1 supply type problem
- 204: L1 supply not supported
- 205: L1 supply not identified
- 206: L2 supply problem
- 207: L2 supply out or missing
- 208: L2 supply type problem
- 209: L2 supply not supported
- 210: L2 supply not identified
- 211: L1 heater problem
- 212: L2 heater problem
- 213: L1 heater sensor problem
- 214: L2 heater sensor problem
- 215: L1 heater roller problem
- 216: L2 heater roller problem
- 217: Debow problem
- 218: Impresser problem
- 219: Impresser sensor problem
- 220: Impresser heater problem
- 221: Bar code scanner problem
- 222: Firmware version mismatch
- 223: Laminator system mismatch
- Driver-Only Messages
- 500: The printer is not available
- 501: The printer connection was lost
- 502: The card data is missing or is not usable
- 504: The card data is missing or is not usable
- 505: USB communication issue
- 506: A card is currently processing
- 507: The printer is unlocked
- 508: The printer is shutting down
- 509: The printer is offline or suspended
- 510: The printer is unlocked
- Driver SDK Messages
- 511: Cannot lock or unlock the printer. Locks are not installed.
- 512: Cannot lock or unlock the printer. The password is incorrect or invalid.
- 513: Cannot lock or unlock the printer. The printer is busy.
- 514: Cannot lock or unlock the printer. The cover is open.
- 515: Failed to lock or unlock the printer. The locks did not function.
- 516: Timeout expired before bar code could be read.
- 517: Wrong printer job ID.
- Printer Messages
- Appendix A: CR805 Card Printer with Inline Lamination
94 Troubleshooting
116: Magstripe not available
The printer does not have a magnetic stripe option. The card will be canceled.
Remove magnetic stripe data from the card or use a printer that has a magnetic stripe option
installed.
Press the U
SER button on the printer to clear the message. On the PC, click OK to clear the
message.
HINTS & TIPS
Look at the printer configuration label inside the printer component. If the label includes an
“M,” the system has a magnetic stripe option that is not working. Request service.
To process the card without magnetic stripe processing, remove the magnetic stripe data
from the card design and send it again.
117: Reader not available
The printer does not support the personalization being requested for the card. The card will be
canceled.
Change the card data to match the printer’s options and settings or print to a printer that is
configured to support the personalization being requested.
Press the U
SER button on the printer, or click OK on the PC, to clear the message.
HINTS & TIPS
The printer component does not have a reader option. Remove the reader request from the card
and send it again.
120: User paused the printer
The printer was paused while printing.
To complete the current card press the printer’s U
SER button.
On the PC, click OK to clear the message and complete the current card, or click Cancel to cancel
the card.
HINTS & TIPS
If the user pressed the button for several seconds, the card has been canceled.
If this message occurs often, ask your system administrator to set the button sensitivity to a
lower value.