User's Guide
Table Of Contents
- Entrust Datacard CR805 Retransfer Card Printer User's Guide
- Table of Contents
- Chapter 1: Introduction
- Chapter 2: About the Printer
- Chapter 3: Using the Printer
- Chapter 4: Print Cards
- Chapter 5: System Maintenance
- Chapter 6: Troubleshooting
- Locate a Problem Within the Card Production System
- Locate a Problem with Basic Printer Functions
- Installation Problems
- Card Printer Driver Problems
- Card Appearance
- Magnetic Stripe Troubleshooting
- Laminator Troubleshooting
- Advanced Troubleshooting Tools
- Printer Card Jams
- Repair a Broken Ink Ribbon or Retransfer Film
- Messages and Conditions
- Respond to Messages
- Printer Messages
- Close and lock doors
- 100: Request not supported
- 103: Printer problem
- 104: Critical problem
- 105: Magstripe data error
- 106: Magstripe data not found
- 107: Magstripe read data error
- 108: Magstripe read no data
- 111: Card not picked
- 112: Card hopper empty
- 113: Close cover to continue
- 114: Cover opened during job
- 116: Magstripe not available
- 117: Reader not available
- 120: User paused the printer
- 122: Magstripe format problem
- 149: Option not installed
- 150: Print while unlocked
- 151: Failed to lock
- 152: Insert new card side 2 up
- 153: Insert same card side 2 up
- 166: C2 supply out or missing
- 167: C2 supply not identified
- 168: C2 supply not supported
- 170: Insert new card side 1 up
- 171: Insert same card side 1 up
- 172: Insert cleaning card
- 173: Improper shutdown
- 175: C2 supply error
- 176: C2 supply type error
- 228: C1 printhead error
- 229: C2 heat sensor error
- 230: C2 heater error
- 231: C2 heated roller motion error
- 232: Retransfer debow error
- 233: Smart card contact fail
- 234: K1 transport card jam
- 235: K2 transport card jam
- 236: Flipper module rotate error
- 237: C1 supply out or missing
- 238: C1 supply not identified
- 239: C1 supply not supported
- 240: C1 supply error
- 241: C1 supply type error
- 242: RT1 reject tray full
- 243: Card lost
- 245: Configuration error
- 275: Multi-hopper error
- 276: Multi-hopper card jam
- 277: Multi-hopper pick error
- 278: Insert cleaning card in H2
- Laminator Messages
- 177: Laminator not available
- 196: Laminator error critical
- 197: Laminator entry card problem
- 198: L1 area card problem
- 199: L2 area card problem
- 200: Laminator exit card problem
- 201: L1 supply problem
- 202: L1 supply out or missing
- 203: L1 supply type problem
- 204: L1 supply not supported
- 205: L1 supply not identified
- 206: L2 supply problem
- 207: L2 supply out or missing
- 208: L2 supply type problem
- 209: L2 supply not supported
- 210: L2 supply not identified
- 211: L1 heater problem
- 212: L2 heater problem
- 213: L1 heater sensor problem
- 214: L2 heater sensor problem
- 215: L1 heater roller problem
- 216: L2 heater roller problem
- 217: Debow problem
- 218: Impresser problem
- 219: Impresser sensor problem
- 220: Impresser heater problem
- 221: Bar code scanner problem
- 222: Firmware version mismatch
- 223: Laminator system mismatch
- Driver-Only Messages
- 500: The printer is not available
- 501: The printer connection was lost
- 502: The card data is missing or is not usable
- 504: The card data is missing or is not usable
- 505: USB communication issue
- 506: A card is currently processing
- 507: The printer is unlocked
- 508: The printer is shutting down
- 509: The printer is offline or suspended
- 510: The printer is unlocked
- Driver SDK Messages
- 511: Cannot lock or unlock the printer. Locks are not installed.
- 512: Cannot lock or unlock the printer. The password is incorrect or invalid.
- 513: Cannot lock or unlock the printer. The printer is busy.
- 514: Cannot lock or unlock the printer. The cover is open.
- 515: Failed to lock or unlock the printer. The locks did not function.
- 516: Timeout expired before bar code could be read.
- 517: Wrong printer job ID.
- Printer Messages
- Appendix A: CR805 Card Printer with Inline Lamination
20 Using the Printer
User Button and Light
The printer’s USER button displays with a border of light that indicates the system status. Use the
U
SER button to:
Suspend the printer—press the USER button when the LCD panel displays Ready.
Clear a message (recover from an error)—press the USER button once.
Cancel all jobs and clear all pending error messages—press the USER button for two seconds
or more.
Determine whether the system is ready, busy, or not available. Indicators include the
following. Refer to “Messages and Conditions” on page 84 for a list of the LCD messages that
correspond to the U
SER light.
Light Description
Off The printer is off or suspended.
Green The printer is ready.
Blinking green The printer is busy.
OR
An attached component has an error.
Amber The printer is not ready.
OR
The P
OWER button was pressed to turn off
the printer.
Blinking amber The printer has an error.
Color Cycle:
Amber, Green,
Light Green, Off
The printer is not ready or a secure door on
the printer is unlocked. The colors cycle
quickly.
Close and Lock Doors displays on the LCD
panel if no other message is present.