User's Guide
Table Of Contents
- Entrust Datacard CR805 Retransfer Card Printer User's Guide
- Table of Contents
- Chapter 1: Introduction
- Chapter 2: About the Printer
- Chapter 3: Using the Printer
- Chapter 4: Print Cards
- Chapter 5: System Maintenance
- Chapter 6: Troubleshooting
- Locate a Problem Within the Card Production System
- Locate a Problem with Basic Printer Functions
- Installation Problems
- Card Printer Driver Problems
- Card Appearance
- Magnetic Stripe Troubleshooting
- Laminator Troubleshooting
- Advanced Troubleshooting Tools
- Printer Card Jams
- Repair a Broken Ink Ribbon or Retransfer Film
- Messages and Conditions
- Respond to Messages
- Printer Messages
- Close and lock doors
- 100: Request not supported
- 103: Printer problem
- 104: Critical problem
- 105: Magstripe data error
- 106: Magstripe data not found
- 107: Magstripe read data error
- 108: Magstripe read no data
- 111: Card not picked
- 112: Card hopper empty
- 113: Close cover to continue
- 114: Cover opened during job
- 116: Magstripe not available
- 117: Reader not available
- 120: User paused the printer
- 122: Magstripe format problem
- 149: Option not installed
- 150: Print while unlocked
- 151: Failed to lock
- 152: Insert new card side 2 up
- 153: Insert same card side 2 up
- 166: C2 supply out or missing
- 167: C2 supply not identified
- 168: C2 supply not supported
- 170: Insert new card side 1 up
- 171: Insert same card side 1 up
- 172: Insert cleaning card
- 173: Improper shutdown
- 175: C2 supply error
- 176: C2 supply type error
- 228: C1 printhead error
- 229: C2 heat sensor error
- 230: C2 heater error
- 231: C2 heated roller motion error
- 232: Retransfer debow error
- 233: Smart card contact fail
- 234: K1 transport card jam
- 235: K2 transport card jam
- 236: Flipper module rotate error
- 237: C1 supply out or missing
- 238: C1 supply not identified
- 239: C1 supply not supported
- 240: C1 supply error
- 241: C1 supply type error
- 242: RT1 reject tray full
- 243: Card lost
- 245: Configuration error
- 275: Multi-hopper error
- 276: Multi-hopper card jam
- 277: Multi-hopper pick error
- 278: Insert cleaning card in H2
- Laminator Messages
- 177: Laminator not available
- 196: Laminator error critical
- 197: Laminator entry card problem
- 198: L1 area card problem
- 199: L2 area card problem
- 200: Laminator exit card problem
- 201: L1 supply problem
- 202: L1 supply out or missing
- 203: L1 supply type problem
- 204: L1 supply not supported
- 205: L1 supply not identified
- 206: L2 supply problem
- 207: L2 supply out or missing
- 208: L2 supply type problem
- 209: L2 supply not supported
- 210: L2 supply not identified
- 211: L1 heater problem
- 212: L2 heater problem
- 213: L1 heater sensor problem
- 214: L2 heater sensor problem
- 215: L1 heater roller problem
- 216: L2 heater roller problem
- 217: Debow problem
- 218: Impresser problem
- 219: Impresser sensor problem
- 220: Impresser heater problem
- 221: Bar code scanner problem
- 222: Firmware version mismatch
- 223: Laminator system mismatch
- Driver-Only Messages
- 500: The printer is not available
- 501: The printer connection was lost
- 502: The card data is missing or is not usable
- 504: The card data is missing or is not usable
- 505: USB communication issue
- 506: A card is currently processing
- 507: The printer is unlocked
- 508: The printer is shutting down
- 509: The printer is offline or suspended
- 510: The printer is unlocked
- Driver SDK Messages
- 511: Cannot lock or unlock the printer. Locks are not installed.
- 512: Cannot lock or unlock the printer. The password is incorrect or invalid.
- 513: Cannot lock or unlock the printer. The printer is busy.
- 514: Cannot lock or unlock the printer. The cover is open.
- 515: Failed to lock or unlock the printer. The locks did not function.
- 516: Timeout expired before bar code could be read.
- 517: Wrong printer job ID.
- Printer Messages
- Appendix A: CR805 Card Printer with Inline Lamination
CR805 Retransfer Card Printer User’s Guide 67
The Card Printer Driver does not detect the network-
connected printer
The Card Printer Driver does not detect the USB-connected
printer
Problem Solution
The Printer Properties >
Status tab shows the
printer is not available.
Make sure that you use the same type of data cable—USB or
network—that was used when the printer was installed. You
cannot switch the type of data cable after installation.
Make sure that the current printer IP address is the same as
the IP address on the Printer Properties > Ports tab. For more
information about retrieving the printer’s IP address, refer to
“Retrieve the Printer’s Network IP Address” on page 23.
Message 500 displays
after you send a card to
print.
If this happens often, consider switching from DHCP network
addressing to static IP addressing. For more information about
setting the Card Printer Driver network communication value,
refer to the “Printer Manager” section of the card printer’s
Installation and Administrator’s Guide.
The network is not
operating properly.
Test the network using another device and fix or report
network problems. To test the network, print to a different
(paper) printer or verify the availability of network drives.
The printer is not
connected to the
network, or the PC is
not connected to the
network.
Make sure that both ends of the data cable are connected.
Replace defective cables if needed.
Problem Solution
The Printer Properties >
Status tab shows the
printer is available, but
Message 500 displays
after you send a card to
print.
Make sure that you use the same type of data cable—USB or
network—that was used when the printer was installed. You
cannot switch the type of data cable after installation.
Make sure that both ends of the data cable are connected.
Replace a defective USB cable if needed.