USER MANUAL (English) VIDEO DOOR PHONE SYSTEM Item No. : 14215 The design and specifications can be changed without notice to users. Copyright of this manual is reserved. 1 2 3 4 5 6 7 8 9 * 0 # Version2.0.1.2.02.
CONTENTS Adjustable Camera Camera Lens Night View LED Speaker LCD Screen 350mm ID Card Window Digital Keypad 1 2 3 4 5 6 7 8 9 * 0 # 3 2 1 Connectiong Port Microphone 128mm 63mm With Rainy Cover 2. Terminal Descriptions SD Card Slot L1 L2 3 2 1 J/KMB • • • • • • • • • • +12V CN-LK EB+ EBN.O LK+ LK- 1. Parts and Functions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 2. Terminal Descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1 3.
. Door Station Mounting 1 4. System Connection 2 Basic IN-OUT Wiring: 3 Camera angle mm 147 ON CALL UNLOCK TALK/MON 1 2 3 4 56 IN-USE 395mm Code=32, DIP-6=on 42m m ON CALL UNLOCK The view for rainy cover after mounted Drill a hole and attach the rainy cover to it 4 Adjust the camera angle and attach the metal to the panel and wire correctly.
5. Door Lock Connections Multi Door Stations Wiring: ON 1. Internal Power Supply Mode CALL UNLOCK ON TALK/MON IN-USE IN-USE 1 2 3 4 5 6 Use the power of the system to supply for the electronic lock, so that the lock can be connected to the door station directly, without an additional power supply for the electronic lock. Note that the door station can only output 12Vdc power, therefore the kind of lock is limited.
6. Door Station Configurations 1. About room code(address): 2. External Power Supply Mode When the electronic lock is over 12 Vdc, additional power supply for the lock is needed. • The power supply for the lock must be less than 48Vdc 1.5A. • The Jumper must be removed when using external power supply. The default setting is Power-on-to-Unlock type(Normally open mode), if use Power-off-to-Unlock type, change the Unlock Relay mode to Normally closed mode .
Basic Tools Detail : Table 2 (Installer Setup) : Item Table 1 : Item 1. Installer Setup 2. Setup [0] [05] [0] [0] 1. Language 2. Tone Select 3. Tone Volume 4. Unlock Code 5. Display Mode 6. Clock ... 7. Setup Code ... 8. About ... 9. Default ... [1] [03] [08] [1111] 1. Add Card ... 2. Delete By Card 3. Delete By M.code 4. Cards Information 5. Format 3. Card Manage 4. Online Monitors To search the online monitors, input the monitor code number to search 5.
Table 3 (Setup) : Table 2.1(Parameters): Item Monitor Timing Description Factory Set To show the monitor time, Range from 6s to 600s 30s To show the surveillance time for each Door Station or CCTV camera.Range from 6s to 600s 40s Wait Timing To show the calling wait time, Range from 10s to 600s 30s Talk Timing To show the limitation time of talking, Range from 10s to 600s 90s Monitor & Speak To enable Indoor Monitor under monitoring state can speak to Door Station at same time.
Table 4 (Card Manage): Item Description Factory Set 1. ID Code.[1] >> Debug State << 2. Unlock Timing[05] Add Card ... To add the user card 0-# Delete By Card To delete card by user card 1-# Redial Tools 1. Installer Setup 2. Setup Delete By M.code To delete card by room code Cards Information To show the informations about cards Format To format informations about cards 4. Calling and Unlock Operation: 2-# To o l s Exits 3. Card Memory Pres NO. 4 .
. Change Unlcok Code: 7. Change Installer Code(administrator password): The Installer Code is the password to access the door station debug State. The default Installer Code is '66666666'. Note that if the Default Set have been activated, the Installer Code will be set to default value. 1. ID Code >> Debug State << If door station runs as Debug State, you can press “1#” to activate Tools Menu, then select “2” to enter setup page,then select 4 item.If it runs as Normal State, follow these steps: [1] 2.
[--] [01] * Back # Save Enter Add Card menu, and Room Code is asked. 4. Cards Information Enter Card Information page, and the screen will display the authorized User Cards count, and card read access events count. [01] C a r d numbs : 1 5 9 7 7 1 3 1 Show the card Show The Card * Back # Save * Back # Save Us C a er rd Please Input Room Code Card information: 1. AddCard ...
Setup [ 8002 ] 1 2 3 4 5 6 7 8 9 * 0 # 1. Language [1] 2 . To n e S e l e c t [ 0 3 ] 3 . To n e V o l u m e [ 0 3 ] Check online monitors: 1. Language 5. Display Mode Press No. to select Please Input Password 6. Clock 7. Setup Code 8. About 9. Default *Back >> Debug State << [----] 4. Unlock Code[1111] ( Code Number) *Back # Save 0-# Redial 1-# To o l s 2-# Exits 4. Online Monitors Tools Press 1 Input 4 digits code number, Refer to the table.
7. Specification • • • • • • • Power supply : DC24V(Powered by DT-DPS) Camera Lens : 1/4 ACS 4T image sensor with DSP processor Power consumption : Standby 3W;Working status 9W Screen : 3.