. Getting Started 8 9 4 1 3 2 5 6 7 8 2 1) Connection, Call (Mode), Mute, Battery 2) Microphone 3) Multi-function button 4) Mode Button (Privacy handset) 5) Volume up Button 6) Volume down Button 7) Charging Port 8) Speaker 9) Power on/off button
. Charge your BHF5000 device Make sure that your speakerphone is fully charged before you start using it. Use the USB cable to con nect BHF5000 to the car ch arger. Plug the ca r charger into your car’s power outlet. The status light will light up red while charging. When fully charged the status light green on. Note) A fully charged battery prior to first use is recommended. A full charge is approximately two and a half hours.
4. Using Hands free 1) Slide the I/O switch to turn the speakerphone on or off. The first time you turn your in-car speakerphone on, it automatically enters pairing mode. When not conne cted to a phone, the speakerphone turns of f automatically af ter 5 minutes. Tap MFB button to turn the speakerphone on again. 2) Connecting with your phone automatically Pairing is only neede d the first time a spea kerphone and phone are u sed together.
2 tones and the call is routed to your mobile phone. 5) Rejecting calls Hold onto the “MFB” button for 1 second to reject an incoming call. 6) Redial last outgoing call To redial a number th at you have rece ntly call, Press the “M FB” button twice and the call is connected. Note) Recent call can be incoming or outgoing number depending on your m obile phone function. 7) Volume control To increase the volume: Press the “+” bu tton to increa se volume by one level.
11) Caller ID and name announcement During an incoming call BHF5000 will access the phonebook on your m obile phone and announce the name of the caller. If the name is not stored in your phonebook and your phone supports PBAP it will announce the number of the caller instead. 12) Advanced Multiuse™ BHF5000 can be connected to two mobile devices at the same time. 5.
. LED Indicators – Technical description Status Standby/ Idle Pairing mode Connected Incoming/Outgoing call (Hands-free mode) Incoming/Outgoing call (Handset mode) Active call (Hands-free mode) Active call (Handset mode) Low battery LED Indicator Link LED is blinking one time on every 3 seconds Link LED and Hands-free LED are alternately blinking rapidly. Link LED blinking two times on every 2 seconds Hands-free Call Status LED is blinking rapidly. Handset Call Status LED is blinking rapidly.
3. Pairing Mode Enter pairing mode 3.1 Automatic pairing mode automatically if paired N/A N/A MFB Tap device list is empty Cancels pairing mode. 3.2 Cancel pairing mode Hands-free goes into connectable state. Delete paired device 3.3 information and last Empty pairing list connected device information MFB + Volume Long press down 4. Connectable state Setting the hands free 4.
4. Single call Transfer call from 4.1 Transfer call hands-free to phone or from phone to MFB Long press MFB Long press MFB Tap hands-free Audio does not exist 4.2 Transfer call on hands-free. Transfer audio from phone to hands-free Audio exist on hands- 4.3 End call 4.4 Hold active call Hold active call MFB Press 4.5 Activate held call Activate held call MFB Press 4.6 Volume up Increase volume level Volume up Tap 4.7 Volume down Decrease volume Volume level down 4.
5.6 Mute Mute Mic – Tx 5.7 Un-mute Un-mute Mic – Tx Volume down Volume down Press Press 6. Three way call – On hold 6.1 Release active activate Release active call held and activate held call Hold active call and MFB Tap MFB Press 6.2 Swap calls 6.3 Release held Release all held calls MFB Double tap 6.4 Volume up Increase volume level Volume up Tap 6.5 Volume down Decrease volume Volume level down 6.6 Mute Mute Mic – Tx 6.
2. Incoming call state 2.1 Answer Answer incoming call MFB Tap 2.2 Reject call Reject incoming call MFB Double tap MFB Tap MFB Long press MFB Tap MFB Tap 3. Outgoing call state 3.1 Cancel outgoing call Cancels outgoing call 4. Single call Transfer call from 4.1 hands-free to phone Transfer call or from phone to hands-free Audio does not exist 4.2 on hands-free. Transfer call Transfer audio from phone to hands-free Audio exist on hands- 4.3 End call 4.
waiting on other phone – put current call on hold Reject incoming call 5.3 Reject waiting on other phone – MFB Double Tap Increase volume level Volume up Tap Decrease volume Volume level down maintain current call 5.4 Volume up 5.5 Volume down 5.6 Mute Mute Mic – Tx 5.7 Un-mute Un-mute Mic – Tx Volume down Volume down Tap Press Press 6. Two active call – other phone’s call is on hold 6.
FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rul es. These limits are de signed to pro vide reasonable protection against harmful interference in a re sidential installation. This equip ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
