EST9120/EST16120 User Guide USER GUIDE EST9120/EST16120 9/16 channel MPEG-4 Triplex DVR V. 1.5 This document contains preliminary information and subject to change without notice.
EST9120/EST16120 User Guide SAFETY PRECAUTIONS EXPLANATION OF SYMBOLS This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance. This symbol is intended to alert the user to the presence of unprotected “dangerous voltage” within the product’s enclosure that may be strong enough to cause a risk of electric shock CAUTION THIS PRODUCT HAS MULTIPLE-RATED VOLTAGES (110V AND 220V).
User Guide WARNING THE PRODUCT SHOULD BE INSTALLED BY A TRAINED PROFESSIONAL. THE DVR SHOULD BE POWERED OFF WHEN CONNECTING CAMERA, AUDIO, OR SENSOR CABLES. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY DAMAGES CAUSED BY IMPROPER USE OF THE PRODUCT OR FAILURE TO FOLLOW INSTRUCTIONS FOR THE PRODUCT. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY PROBLEMS CAUSED BY OR RESULTING FROM THE USER PHYSICALLY OPENING THE DVR FOR EXAMINATION OR ATTEMPTING TO FIX THE UNIT.
EST9120/EST16120 User Guide THE LIST OF CONFIGURATION DVR SET CLIENT SOFTWARE CD REMOTE CONTROLLER BATTERY MANUAL (SERVER & REMOTE CLIENT S/W) RUBBER RINGS & SCREWS (4x4x4EA) IDE HDD CABLE(2EA) HDD BRACKETS(4EA) POWER CABLE 110V & 220V 4
User Guide THE OPERATION OF REMOTE CONTROLLER POWER Power On/Off ID (DVRs) Input DVR ID (ID : i.e.
EST9120/EST16120 User Guide VIDEO SIGNAL SELECT / SETTING SETTING Video mode Video output NTSC PAL BNC VGA O X O X X O O X O X X O X O X O NOTICE Do not change the setting when the power is on. When the position of the switch is changed, the DVR should be rebooted to apply the new setting.
User Guide HDD INSTALLATION HDD installation order 1. Primary Master HDD 2. Primary Slave HDD 3. Secondary Master HDD 4. Secondary Slave HDD NOTICE The brands and models of all HDD should be the same. If the brands and models of each HDD are different with others, the DVR could not recognize HDD.
EST9120/EST16120 User Guide Compatible HDD models BRAND CAPACITY RPM BUFFER INTERFACE HITACHI 80GB 7200RPM 2M E-IDE 160GB 7200RPM 8M E-IDE 250GB 7200RPM 8M E-IDE 80GB 7200RPM 2M E-IDE 160GB 7200RPM 8M E-IDE 250GB 7200RPM 8M E-IDE 80GB 7200RPM 2M E-IDE 160GB 7200RPM 2M E-IDE 80GB 7200RPM 2M E-IDE 160GB 7200RPM 8M E-IDE 250GB 7200RPM 8M E-IDE 40GB 7200RPM 2M E-IDE 80GB 7200RPM 2M E-IDE 160GB 7200RPM 2M E-IDE 250GB 7200RPM 2M E-IDE MAXTER SAMS
User Guide SPECIFICATIONS ITEM Description Channel, 9/16CH, Composite 1.0Vp-p, 75 Ohm Input Level Input Video Signal Format NTSC/PAL Video Loss Check Yes Main Monitor 1 CH BNC, 1 CH S-VIDEO, 1CH VGA Output Output Output Level Composite 1.0Vp-p +_0.2, 75 Ohm Signal Format NTSC/PAL & VGA Etc Output 9/16CH Loop-back , 1CH SPOT Input & Output 4 CH Line input & 1 CH Line output Audio Codec G.
EST9120/EST16120 User Guide Playback Fast Forward / Speed Reverse × 2, 4, 8, 16, 32, Max Search Mode Time, Event, Channels Interface Type Internal EIDE/ATA133 Max Capacity 250GB of 1 HDD HDD Max HDD 4 Number Storage File system NaFS: Own developed & Designed for never broken by any power failure USB 2.
User Guide TABLE OF CONTENTS 1. Features ...................................................................................................................................13 2. Name, Function and Connection..............................................................................................14 2-1. Front Panel ....................................................................................................................14 2-2. Rear Panel .......................................................
EST9120/EST16120 User Guide 6-5. Search and Playback Viewer .........................................................................................49 6-5-1. Main user interface ..............................................................................................49 6-5-2. Main control panel ...............................................................................................49 6-6. System configuration .....................................................................................
User Guide 1. Features ● 9/16 channels real-time live display and 16channels simultaneous playback. ● MPEG-4 - Unbeatable recording picture quality and compression ratio has been tuned for years. It best fits for minimizing recording space and networking speed. ● TRIPLEX - Simultaneous Recording, Playback, and Networking ● NaFS (File System developed) - Designed & developed for preventing loss and broke of recording data by any power failure. ● DSP solution -To be updated up to 240/200fps recording speed.
EST9120/EST16120 User Guide 2. Name, Function and Connection 2-1. Front Panel The following information will help you operate the front panel controls. Figure 2.1.1. Front panel Table2.1.1. Indication lamps Name Description HDD LED light is on when the system is accessing hard disk. REC LED light is on when the system is recording video data. ALARM LED light is on when alarm sensor(s) is/are triggered or motion is detected.
User Guide FREEZE/ Press to freeze and capture video in jpeg format in live or playback mode. CAPTURE REW/ Press to rewind the footage at 1x, 2x, 4x, 8x, 16x, and 32x speed in playback LOG mode or to see the LOG LIST in live display mode. F/REW Jump/Step backward. In playback mode, the playback position moves 60 seconds backward. F/ADV Jump/Step forward. In playback mode, the playback position moves 60 seconds forward.
EST9120/EST16120 User Guide 2-2. Rear Panel Figure 2.2.1. Rear Panel Table 2.2.1. Rear panel connections Connection VIDEO IN Description 9/16 connectors for video input. Connect camera output to Video-in (NTSC/PAL) VIDEO OUT 9/16 connectors for video output.(loop back) SPOT Composite video output for spot monitoring. VIDEO Composite video output in NTSC or PAL format S-VHS S-VHS output VGA Connector for VGA monitor AUDIO IN 4 connectors for audio input.
User Guide Provides simple On/Off switching by using relay. 0.5A/125V, 1A/30V POWER Connect AC115/230V power cable. SWITCHES TEST 422/485 For future use Select 422 or 485 VGA Set to ON when VGA monitor is used. PAL Set to ON when video is PAL CAUTION: Once the position of the switch is changed, 9-16CH should be rebooted to apply the new setting value.
EST9120/EST16120 User Guide 3. Getting Started – Setting Up the DVR The following sections detail the initial setup of the DVR 3-1. Setup – Main Screen When you press the SETUP button, the DVR will ask for a password. The default password is 1111, which can be entered by pressing the up button 4 times and then pressing the SEL button. We recommend you protect the system by assigning a new password immediately. The procedure for assigning a password is found in section 3.6.
User Guide LIVE OSD SEQUENCE SEQ-DWEL TIME OSD CONTRAST CHANNEL RECORD DISPLAY, BRIGHTNESS, CONTRAST, HUE, SATURATION RESOLUTION CHANNEL FRAME RATE, QUALITY, RECORDING, MOTION ZONE, MOTION SENSIVITY, SENSOR TYPE, PRE RECORD, POST EVENT RECORD, AUDIO, SCHEDULE DEVICE ALARM-OUT PTZ SPOT CHANNEL SPOT EVENT DWELL TIME KEY TONE REMOTE CONTROL ID SYSTEM DVR ID DESCRIPTION LOAD FA CTORY DEFAULT LOAD DEFAULT DATE FORMAT SET DATE & TIME LANGUAGE DAY LIGHT SAVING SECURITY ADMIN PASSWORD USER PASSWORD NETW
EST9120/EST16120 User Guide 3-2. Setup – Live Mode Set the values for live display. Navigate through the menu items by pressing the UP or DOWN button. The value of the menu item may be changed by pressing the LEFT or RIGHT button. Figure 3.2.1. Live mode setup screen Table 3.2.1. Menu items in LIVE mode setup Item OSD SEQUENCE SEQ-DWELL TIME Description Enable/disable on-screen-display. Enable/disable SEQ button Set the dwell time for each, 4 or 9 channel display in sequential display mode.
User Guide 3-3. Setup – Recording Mode Set the values for recording video. Navigate through menu items by pressing the UP or DOWN button. User can change the value of the menu item by pressing the LEFT or RIGHT button. Figure 3.3.1. Recording mode setup screen Table 3.3.1. Menu items in Recording mode setup Menu item RESOLUTION CHANNEL FRAME RATE Description Set the resolution to 704x480 or 352x240(NTSC). Select a channel for applying the following settings. Set the frame rate for the specified channel.
EST9120/EST16120 User Guide MOTION ZONE Select Full Zone or Partial Zone for motion sensing. MOTION SENSITIVITY Set the motion sensitivity for the specified channel. Control the motion sensitivity from 1 to 9. Enable setting up to 4 sensors of 9 sensors for the specified SENSOR RECORDING channel. PRE RECORD Enable/disable pre-event recording. Pre-event recording time is 5 second and only intra-frames are recorded for pre-event recording.
User Guide 3-3-2. Recording Schedule Select SCHEDULE in the RECORD menu to set up the recording schedule. Button functions applied in the recording schedule are summarized in the following table. Navigate through the items to highlight by using the 4 direction key buttons and set up the recording schedule by using the buttons summarized in the following table. [ALL] : When ALL is highlighted, selected recording mode by pressing SEL button is applied to entire time zone and channels.
EST9120/EST16120 User Guide 3-4. Setup – Device Mode Set the values for device setting. Navigate through menu items by pressing the UP or DOWN button. User can change the value of the menu item by pressing the LEFT or RIGHT button. Figure 3.4.1. Device mode setup screen Table 3.4.1. Menu items in Device Setup screen Item ALARM-OUT PTZ SPOT CHANNEL SPOT EVENT DWELL Description Set the sensor, motion, and video loss for each alarm.
User Guide 3-4-1. ALARM-OUT Table 3.4.2. Menu item in ALARM-OUT Setup screen Item Description ALARM OUT Select alarm from 1 to 8. SENSOR IN Enable setting up to 4 sensors of 16 sensors. MOTION ON Enable setting up to 4 cameras of 16 cameras. VIDEO LOSS ON Enable setting up to 4 cameras of 16 cameras. ALARM DURATION Set the dwell time of alarm from1 to 60seconds. SENSOR TYPE Select sensor from 1 to 16.
EST9120/EST16120 User Guide 3-4-3. PTZ Setup To control the PTZ functions of the camera, connect the controller to the RS-485 port. For speed dome cameras that supports RS-485, connect them directly to the RS485 port. But if the camera is controlled with RS-232C, it is needed to use Signal Converter (RS-485 to RS-232C) In the PTZ Control setting in the setup menu, user can select or set the protocol type of the camera which is the same as the one that is installed on the site.
User Guide Figure 3.4.5. PTZF control screen Table 3.4.4. Button functions in PTZF control Item Description PAN / TILT Use the UP or DOWN button for TILT and LEFT or RIGHT button for PAN of the selected camera. ZOOM / FOCUS Use the UP or DOWN button for ZOOM in or out and LEFT or RIGHT button for FOCUS near or far of the selected camera. INITIALIZE Initialize the PTZ settings of the selected camera. 3-5. Setup – System Mode In this menu, system parameters can be input.
EST9120/EST16120 User Guide DESCRIPTION System information. LOAD DEFAULT Select OFF or ON. Select ON to load defaults. DATE FORMAT Select the preferred date and time display SET DATE&TIME Set the current date and time. After setting is done, press the SEL button and select CONFIRM. Then the system is automatically rebooted to apply the settings. USB UPGRADE Select this item to upgrade firmware by using USB memory stick. Refer to the direction from the section 6.UPGRADING FIRMWARE.
User Guide Figure 3.5.3. DVR information display screen Figure 3.5.4.
EST9120/EST16120 User Guide Figure 3.5.5. Daylight Saving setup screen 3-6. Setup – Security Mode In this menu, password and security parameters can be input. Navigate through the menu items by pressing the UP or DOWN button. User can change the value of the menu items by pressing the LEFT or RIGHT button. Figure 3.6.1.
User Guide Table 3.6.1. Menu Items in Security Setup Screen Item Description ADMIN PASSWORD Set a password for administrator. Once this menu is selected, the system will ask you current password and new password. Follow the procedure provided by the system. The password numbers can be input by using direction keys. The default password is 1111. USER PASSWORD Set a password for user. Once this menu is selected, the system will ask you current password and new password.
EST9120/EST16120 User Guide DDNS NAME The DDNS sever name is www.esthub.co.kr Registration>> Check the MAC address of DVR from SETUP-> SYSTEM-> DESCRIPTION. Please contact a distributor or an installer to register your DVR on DDNS Server. Register your own domain name on DDNS Server. After your own domain name and MAC address of DVR are registered on DDNS server, user can access to network with own domain name. 3-7-1.
User Guide Figure 3.7.1. Network setup screen 3-7-2. Network types There are three network types. Each type requires different settings. LAN To use the LAN option when connecting the DVR to a network, the following information is required. If you do not have this information, see your network administrator. Table 3.7.2. LAN Item IP Description The fixed IP address of the DVR GATEWAY The IP address of the gateway SUBNET MASK The subnet mask for the LAN DNS Set the DNS IP.
EST9120/EST16120 User Guide If the network connection does not allow additional IP addresses, than an IP sharing device will be needed. In this case, forwarding may be needed to allow for a network connection. For more information on port forwarding, see the documentation for your IP sharing device or your network administrator. ADSL To use the ADSL option when connecting the DVR to a network, the following information is required. If you do not have this information, see your network administrator.
User Guide 3-8. Setup - Storage Mode User can set recording mode in the hard disk drive or initiate format of the hard disk driver. Figure 3.8.1. Storage setup screen Table 3.8.1. storage setup Item OVERWRITE FORMAT Description Overwrite existing material when hard disk drive is full. Format hard disk drive. 3-9. Saving Setup To preserve the changed setup values, select the SAVE SETUP menu and select CONFIRM.
EST9120/EST16120 User Guide 4. Live & Search 4-1. Live Window In the Live window, video inputs from the cameras are displayed on the configuration of the live setup. Various indicators showing the status of the DVR are shown as OSD symbols. Refer to Table 4.1.1 for the meanings of the indicators. Figure 4.1.1. Live window Table 4.1.1.
User Guide Button SETUP SEQ Description Launch the SETUP menu. Enable/disable the automatic sequential display in full or quad mode. The channel display in quad mode is followed the settings in the setup menu. PLAY/PAUSE Launch the SEARCH window. Use to select channel 1to 4 in full screen mode or to change the quad display in quad display mode by using the LEFT or RIGHT button. And use to select and highlight a channel to display in full display mode in 9 split display mode.
EST9120/EST16120 User Guide Figure 4.2.1. Search mode screen Searching for an event: 1. Select a date of the video to begin searching, Use the LEFT or RIGHT button and UP or DOWN button to navigate through the date. 2. Once you have selected the date, press the SEL button to move to the CHANNEL selector. 3. Use the LEFT or RIGHT button to change the channel selection from ALL to any of the nine available channels. 4. Once you have selected the channel, press the SEL button to move to the TYPE selector. 5.
User Guide Figure 4.2.2 Search list 4-3. Play mode During the playback of a recorded event, the mode changes from SEARCH to PLAY. While in PLAY mode, you may return to SEARCH LIST by pressing the ESC button. Figure 4.3.1.
EST9120/EST16120 User Guide Table 4.3.1. Button functions in Play mode Button Description ESC Return to the previous menu screen or exit from the setup menu REW Press to rewind the footage at 1x, 2x, 4x, 8x, 16x, and 32x speeds. Reverse playback speed is shown as -1x(normal), -2x (2 times normal), -4x (4 times normal), -8x (8 times normal), -16x (16 times normal), and -32x (32 times normal) at the bottom right of the screen. F/REW Jump/Step backward. The playback position moves 60 seconds backward.
User Guide Figure 5.1.1. Archive mode screen The still image will be stored into the hard disk drive and can be transferred to the USB storage device later. In playback mode, press the FREEZE/CAPTURE button to launch the archiving function. The system will ask whether to store still image or video. If the user selects still image, it will store captured image into the hard disk drive. If the user selects video, it will store video into the hard disk drive.
EST9120/EST16120 User Guide Figure 5.2.1. Archive menu screen Press the SEL button to retrieve a list of archived image or video. Select one of the files in the archived list by using the UP or DOWN button, and then press the FREEZE/CAPTURE button to transfer to the USB storage device. When there is enough space for archiving, the system will start transferring the file.
User Guide Figure 5.2.2. List of archived files DivX player which supports DivX codec is required for proper playback of the AVI format. DivX player may be downloaded from: http://www.divx.
EST9120/EST16120 User Guide 6. Network The DVR provides a live remote monitoring feature. Remote monitoring requires installation of a software client program on your PC. A LAN connection using the RJ45 connector on the rear panel is mandatory for remote connection. For detailed features of the client program, please refer to the client program user guide. For local operation purposes, the frame rate is limited to 1 frame/sec when there is no recording operation in the DVR.
User Guide 6-2. Minimum PC requirements Minimum Recommended Intel Pentium Ⅲ Intel Pentium Ⅳ 500Mhz 2Ghz Memory 128MB 256MB VGA 16MB 64MB Resolution 1024x768 1024x768 Disk space 10MB 10MB OS Windows 2000 Windows 2000 Professional, XP Professional, XP Network 10/100Base T 10/100Base T Others Direct X 8.1 or Higher Direct X 8.1 or Higher CPU Before installing the program, check the PC specifications.
EST9120/EST16120 User Guide 6-4-1. Main user interface 6-4-2. Main control panel Button Description Display of current time. Display of current connected IP address Click this icon to connect to the DVR CONNECT Once you click the connection icon, this pop up window appears. Enter the IP address (or Subdomain name) and a port number. And select the protocol type and enter password.
User Guide Click this icon to disconnect to the DVR DISCONNECT Click this icon to search for recorded videos. SEARCH Click this icon to see a live video. LIVE Click this icon to lock all operations of client software LOCK Click this icon to unlock all operations of client software. UNLOCK Once you click the lock or unlock icon, this pop up window appears. You need to remember the pass word and enter the pass word when you try to operate the client software.
EST9120/EST16120 User Guide Click this icon to capture a still image CAPTURE Once you click the capture icon, this pop up window appears. A still image is captured in bmp file format. Click this icon to setup configuration of client software. SETUP Click this icon to terminate client software. TERMINATE S/W Alarm indicators for each channels.
User Guide 6-5. Search and Playback Viewer 6-5-1. Main user interface You can access to search window by clicking the search icon on the upper left of main user interface. 6-5-2. Main control panel Button Description It shows the recording time of the selected data by adjusting of scale in the middle of the bottom of the main user interface. Display of current connected IP address Click this icon to see live videos.
EST9120/EST16120 User Guide Click this icon to exit from the operations of client software EXIT Click this icon to capture a still image of recorded video. CAPTURE Once you click the capture icon, this pop up window appears. A still image is captured in bmp file format.
User Guide It shows the recorded data in green bar. You can adjust the time line scale and click the play icon to display the recorded video Click this icon to play the recorded video Click to pause/stop the displaying video Click to fast forward the displaying Click to rewind the displaying Click to backward by 1frame Click to forward by 1frame 6-6. System configuration Click the setup icon to setup the configuration of DVR. 6-6-1. General Once you click the setup icon, this pop up window appears.
EST9120/EST16120 User Guide Set a password for security options.
User Guide 6-6-2. Site It shows the channel information connected to DVR and you can change the channel title 6-6-3. Event You can set event items, the capacity of local disk and save path for log.
EST9120/EST16120 User Guide 6-6-4. Record You can set the recording conditions for always, event and auto recording. And you also can set each or all channels for recording. When you set the recording condition to event, you can set event for motion or alarm with duration. And you also can set each or all channels for event recording. 7-6-5. Disk You can set the local disk and the capacity of it for recording. You can select the recording way to overwrite or stop recording when the local disk is full.
User Guide 7 Using DDNS 7-1. DDNS Registration Procedure [Step 1] [Step 2] Enter the DDNS Web site (http://www.esthub.co.kr) . Input ID, Password, Name, E-Mail . [Click] [Click] [Step 3] . Start registration Procedure. . [Click] [Step 4] .MAC Address : Label means the Mac Address of . Input MAC Address, Registration No. , DVR Domain Name. [click] e.g) 000269003B24 .Registration No. : Each MAC Address has its ownRegistration number. .
EST9120/EST16120 User Guide [Step 5] [Step 6] . Able to confirm the present status of domain . When need to change the information of User, name(entel.esthub.co.kr) in Server List. Select Personal Info. Change button. 7-2. DVR SETUP [Step 1] [Step 2] . Go to SETUP, and Select Network to choose . Change the value on DDNS to ON. DDNS enable. [Step 3] . Configure the DDNS address to www.esthub.co.kr and save DVR then it will be reboot automatically.
User Guide 7-3. Using Client Program [Step 1] [Step 2] . Execute the Program. . Program will be executed. . xxxxx.exe in desktop [Click] [Step 3] . Program will be executed. . [Click] [Step 4] . IP Address : Domain Name(entel.esthub.co.kr) or . Insert registered values like below. Static IP. . Port No : 5445(Default Value) . Protocol : TCP(Default Value) .
EST9120/EST16120 User Guide [Step 5] . In Desttop of Windows. Start -> Run -> CMD [Enter] . [Step 6] . In order to check the status is normal, Use Ping Ping entel.esthub.co.kr [Enter] Test This picture shows 61.73.18.198 is bound to entel.esthub.co.kr in DDNS.
User Guide USER GUIDE CMS (Central Monitoring Software) Version: 1.
EST9120/EST16120 User Guide TABLE OF CONTENTS 1. CMS – Central Monitoring Software.............................................................................................61 1-1. Overview ............................................................................................................................61 1-2. Minimum PC requirements ................................................................................................61 1-3. Installing the program ....................................
User Guide 1. CMS – Central Monitoring Software 1-1. Overview CMS supports remote live viewing, remote search, backup, camera control and other functions, linking multiple DVRs. 1-2. Minimum PC requirements CPU Intel Pentium Ⅳ 2Ghz Memory 256MB VGA 64MB Resolution 1024x768 Disk space 10MB OS Windows 2000, Professional, XP Network 10/100Base T Others Direct X 8.1 or Higher Before installing the program, check the PC specifications.
EST9120/EST16120 User Guide 1-3. Installing the program 1. Insert the provided CD into the CD-ROM drive of your PC. 2. Run CMS(XXXXXX).exe to start the installation process. 3. Follow the onscreen directions. Enter User Name, Company Name and Serial Number that is provided from the supplier. 4. Select the target folder that the program is installed. 5. Double click the icon to start the program.
User Guide 1-4. Live Monitoring When installation is completed, double click the icon on your desktop to start the program. 1-4-1. Main user interface 1-4-2. Control buttons Button Description Displays the current date and time.
EST9120/EST16120 User Guide Click this icon to search for recorded videos / to see al live Search/Live video. Click this icon to lock/unlock all operations of CMS. Lock/Unlock Once you click Lock/Unlock icon, this pop up window appears. You need to remember the pass word and enter the password when you try to operate the client software. User can control PAN/TILT & ZOON/FOCUS. PAN left /right TILT up/down ZOOM in/out FOCUS in/out Click this icon to play/pause live video.
User Guide HDD storage Indicator of DVR. It shows the status of network connections. Max/Min/Exit of the client viewer The alarm output indicator lights up for 5 seconds if alarm output is activated on the DVR. 1-5. Search and Playback 1-5-1. Main user interface You can access to search window by clicking the search icon on the upper left of main user interface.
EST9120/EST16120 User Guide 1-5-2. Main control panel Button Description Displays the recording time of the selected data by adjusting of scale in the middle of the bottom of the main user interface. Click this icon to see live videos. LIVE Click this icon to capture a still image of recorded video. CAPTURE Once you click the capture icon, this pop up window appears. The still image is captured in either jpeg or bmp file format.
User Guide Click to rewind at 2x and 4x speeds, to reverse at 1frame, to play, to advance 1 frame, and to fast forward at 2x and 4x speeds in playback mode. To select the numbers of display channels Click this icon for Sequential display of each channel in full SEQUENCE screen mode. Use the volume control bar to set the audio level. You can select the audio on or off by clicking the audio icon Click this icon to exit from the operations of client software EXIT 1-5-3.
EST9120/EST16120 User Guide 1-6. System configuration Click the setup icon to setup the configuration of DVR. 1-6-1. General Once you click the setup icon, this pop up window appears. Select security options and set a password. Then when you access any of the selected functions, you need to enter the password. You can also set the save path for capturing and backup. Security Option: Set a password for security options.
User Guide Password’ and ‘Confirm Password’, then press ‘OK’ button. From 2nd PW setting: User needs to enter PW on ‘Old Password’ to change PW. 1-6-2. Site This option shows the channel information of the DVR and allows you to change the channel title. 1-6-3. Event You can set event items, the amount of local disk space you want to allow, and the save path for the log. z LOG – Select to save event log into ‘log file’. z ICON – Select to display event on live video.
EST9120/EST16120 User Guide 1-6-4. Record You can set the recording conditions for Always, Event, or Auto recording. You can also select individual channels or all channels to record. When you set the recording condition to event, you can set event for motion or alarm with duration. And you also can set each or all channels to record.
User Guide 1-6-5. Disk You can select the local disk to use and the amount of disk space you want to allow the program to use for recording. You can also select the option to overwrite data or stop recording when the maximum amount of disk space is full. 1-6-6. About “About” provides network client version information.
EST9120/EST16120 User Guide 1-7. DVR Sites registration and Access 1-7-1. DVR Sites registration 1. Press button. 2. Press SITE menu from the window and then the following registration menu. BUTTONS DESCRIPTION Create New Site: You can create new DVR site, make new group. Add Site to Group: You can add existing site to existing group. Modify: You can modify information of a site. Delete: You can delete a site. Move Item Up/Down 3. Press Button to create new site or add new group.
User Guide Group: To select Group or to add new group. Site Name: Enter a site name. IP Address: Input IP address name or Domain name (Ex. xxxx.standalone4ch.com) Port No.: Input port number of DVR. Protocol: Select network protocol from TCP or UDP. Password: Input password of DVR.
EST9120/EST16120 User Guide 1-7-2. Access button to access sites. 1. Press the connect 2. Select groups or sites and press Connect button.
