ENVIROFIRE WOOD STOVE MODELS 1000, 1600, 1600INS, 2100 OWNERS AND OPERATORS MANUAL SHERWOOD INDUSTRIES LTD.
TABLE OF CONTENTS • PLEASE READ AND SAVE INSTRUCTIONS • • • OPERATING INSTRUCTIONS 3-4 PEDESTAL INSTALLATION 5 • • BRICK INSTALLATION MODEL 1000 6 SAFETY WARNING 2 • MODEL 1600 INSERT 7 • MODEL 2100 8 • FREESTANDING INSTALLATION 9-10 • MOBILE HOME INSTALLATION 11 • FIREPLACE INSERT INSTALLATION 12 • HOW IT WORKS 13 • SPECIFICATIONS 13 • DOOR INSTALLATION 14 • OPTIONAL FAN INSTALLATION (WIRING DIAGRAM) 15 • RATING LABEL COPY 16 • PARTS AND ACCESSORIES 17 • WARRAN
OPERATING INSTRUCTIONS STARTING: Place crumpled paper on the stove floor and cover with kindling. Open the draft fully and ignite. Hold the door slightly a jar for a few minutes and then close tightly. After the wood is burning brightly add more dry wood and, when the fire is hot, use the draft control to adjust the burn rate. This limits the amount of combustion air entering the fuel chamber and can be adjusted from a low burn rate with the handle fully in, to a fast burn with the handle fully out.
DISPOSAL OF ASHES: If you let the ashes accumulate two or three inches on the floor they tend to burn themselves up. Open the small trap door located on the floor of the unit. Push the ashes that have accumulated into the hole were the ashes would drop into the ash pan. Ensure that the trap door is closed properly before relighting the unit. When necessary put the ashes in a metal container with a tightly fitting lid.
PEDESTAL AND LEG INSTALLATION Please read and understand these instructions before installing ash pan and leg option. Failure to follow these instructions carefully could cause personal injury or property damage. All screws are pre installed on the base of the unit. PEDESTAL • Remove the bricks from the unit before starting. • Loosen the two carriage bolts that secure the unit to the pallet. Slide the pallet towards the front to release carriage bolts from the key holed slots in the unit.
MODEL 1000 BRICK PLACEMENT: COMPLETE THE STOVE AND SMOKE PIPE INSTALLATION BEFORE PLACING THESE BRICKS. 1. Place the bottom layers of the sides and back of the firebox. 2. Place the floor bricks. The spaces between the bricks will soon fill with ashes. 3. Finish the sides and back ready to accept the top, ceiling bricks. 4. On the right and left sides, leave the front. top brick out and install this brick last.
MODEL 1600 BRICK PLACEMENT: COMPLETE THE STOVE AND SMOKE PIPE INSTALLATION BEFORE PLACING THESE BRICKS. 1. Place the bottom layers of the sides and back of the firebox. 2. Place the floor bricks. The spaces between the bricks will soon fill with ashes. 3. Finish the sides and back ready to accept the top, ceiling bricks. 4. On the right and left sides, leave the front. top brick out and install this brick last.
MODEL 2100 BRICK PLACEMENT: COMPLETE THE STOVE AND SMOKE PIPE INSTALLATION BEFORE PLACING BRICKS. 1. Place the bottom layers of the sides and back of the firebox. 2. Place the floor bricks. The spaces between the bricks will soon fill with ashes. 3. Finish the sides and back ready to accept the top, ceiling bricks. 4. On the right and left sides, leave the front. top brick out and install this brick last.
FREESTANDING INSTALLATION: CHIMNEY: Vent the stove into a clean, lined, approved masonry chimney in good condition, conforming to local building codes or a listed 6” factory built chimney suitable for use with solid fuels and conforming to, ULC-S629 in CANADA or UL103HT in the U.S.A.. Connect the stove to this chimney with a short and straight 6” (150 mm), 25 gauge or heavier, single wall black or blued steel smoke pipe.
OUTSIDE AIR: A 4” (10.16 cm) fresh air adapter kit is available. This adapter can be installed either on the back pedestal or through the floor under the pedestal. Place the 1/4” mesh screen between the fresh air adapter and the body of the pedestal. (AS SHOWN) NOTE: Fresh air connection to the unit must be a non combustible pipe. (Example: 4” (10.
MOBILE HOME INSTALLATION SPECIAL REQUIREMENTS: Pedestal models 1000 and 1600 are approved for mobile homes. All freestanding installation requirements on the preceding page plus the following must be met: VENTING: In Canada: Any ULC-629 listed chimney system with the accompanying double wall vent connector. In U.S.A. Any HT-103 listed chimney system with the accompanying double wall vent connector.
MODEL 1600 INS FIREPLACE INSERT Unless you are experienced, we recommend installation by your dealer or a professional installer. Install only in a masonry fireplace at least 25” (635 mm) wide, 22” (560 mm) high and 14” (356 mm) deep with an approved lined chimney at least 15 ft (4.6 m) high, both of which have been constructed in accordance with the building code. Be sure the fireplace and chimney are clean and sound without any cracks or loose mortar. Do not remove any bricks or mortar from the fireplace.
HOW IT WORKS SPECIFICATIONS: WIDTH X DEPTH HEIGHT ON PEDESTAL HEIGHT OF BODY FUEL CHAMBER DEPTH X WIDTH X HEIGHT CAPACITY *APPROXIMATE HEATING AREA ** EPA OUTPUT RATING * DURATION ON LOW BURN WEIGHT WITHOUT BRICKS WEIGHT OF BRICKS E.P.A. EMISSIONS SURROUND PANELS MODEL 1000 24 X 21” (.61 X .53 M) 33 “ (.83 M) 22” (.56 M) MODEL 1600 24 X 25.5” (.61 X ..64 M) 33 “ (.83 M) 22” (.56 M) 12.5 X 18 X 12” (.3 X .46 X .3 M) 17 X 18 X 12” (.42 X .46 X .3 M) 1.7 CU. FT. (.048 M 3) 1000 SQ. FT.
DOOR INSTALLATION Remove the door from the packaging. Inspect the door assembly for damage. DO NOT USE DOOR IF GLASS IS BROKEN. Place the door assembly on the two hinge pins mounted on the body of the unit. Open and close the door, applying pressure down, to ensure the door assembly is properly seated on the hinges.
OPTIONAL FAN INSTALLATION The appliance when installed, must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.1 CANADIAN ELECTRICAL CODE. Part 1, SAFETY STANDARDS FOR ELECTRICAL INSTALLATIONS, or THE NATIONAL ELECTRICAL CODE ANSI / NFPA 70 in the USA. CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
DO NOT REMOVE THIS LABEL LISTED SOLID FUEL SPACE HEATER SERIAL NO. MODEL: 1000 WH1600 2100 1600 INS MODEL 1000 SUITABLE FOR USE IN MOBILE HOMES. CERTIFIED FOR CANADA AND THE U.S.A. TESTED TO CSA B366.2/ULC-S627, ULC-S628-M93, UL-1482-1994 REPORT NO. J99011443-231 REPORT NO. 6385 INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURERS INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. USE 6 IN.
PARTS AND ACCESSIORIES PLEASE CONTACT YOUR LOCAL ENVIROFIRE DEALER WHEN REPLACEMENT PARTS ARE REQUIRED.
WARRANTY Because of our high standards Sherwood Industries Ltd. can offer a *Lifetime Warranty on all it’s wood products. Covered under this warranty are Cabinet Sides, Tops, Pedestals, Surround Panels, Removable Air Channel, and Chassis. These steel components are covered against manufacture’s defects for 1 year on parts and labor and for parts only for the next 4 years. Please refer to the warranty agreement for specific details on the coverage of your *Lifetime Warranty. Sherwood Industries Ltd.
SOLID ASH COVER FAN CONTROLLER EF-179 SECONDARY AIR TUBE EF-171 SET OF FOUR (4) LEGS W/ ASH PAN EF-196 CONVECTION BL0WER EF-180 FAN KIT EFW 261 120° TEMPERATURE SENSOR EF-205 FLAT TOP CABINET SIDES EF 1000 PAINTED -EFW 250 GOLD -EFW 251 NICKEL- EFW 252 EF 1600-2100 PAINTED- EFW-265 GOLD- EFW-267 NICKEL- EFW-269 STEP TOP CABINET SIDES ASH PAN LATCH EF-060 SLIDER DAMPER PLATE BRICKS 3” X 9” EF-169, A 4.5” X 4.5” EF-169, B 4.
