SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER. PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE PELLET STOVE Evolution NZ OWNER’S MANUAL PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.
Table of Contents Introduction..............................................................................................................3 Rating Label Location......................................................................................3 Pellet Quality.................................................................................................3 Safety Warnings & Recommendations.........................................................................4 Specifications..........................
Introduction * This manual is designed for the home owner in conjunction with the technical manual. * Rating Label Location: The rating label is located on the inside of the ash pan cover. Pellet Quality: Pellet quality is important, please read the following: Your Enviro pellet stove has been designed to burn 6mm dia wood pellets only. DO NOT use this appliance as an incinerator.
Safety Warnings & Recommendations Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Any unauthorized modification of the appliance or use of replacement parts not recommended by the manufacturer is prohibited. All national and local regulations and New Zealand Standards shall be complied with when operating this appliance.
Safety Warnings & Recommendations retained in the closed container until all cinders have thoroughly cooled. ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 220-240 volts (2.0-2.3 Amps), 50 hertz electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power cord must be purchased from the manufacturer or a qualified ENVIRO dealer.
Specifications Dimensions: Unit Dimensions Height: 871 mm (34 5/16”) Width: 565 mm (22 ¼”) Depth: 595 mm (23 7/16”) 28" (711 mm) Hearth Pad: Width: 619 mm (24 ⅜”) Depth: 670 mm (26 ⅜”) 24 3/8" (619 mm) 22 1/4" (565 mm) 23 7/16" (595 mm) 5 5/8" (144 mm) 34 5/16" (871 mm) 26 3/8" (670 mm) Figure 1: Dimensions of Evolution.
2.0 - 2.3 Amps Unit with Full Hopper ~ 140kg (310lb) Mean Flue Gas Temperature - Medium 162°C (324°F) Fuel Consumption - Medium 1.5 kg/hr (3.31 lb/hr)* Heat/Power Output - Medium 6.3 kW (21516 BTU/hr) Average Emissions Rate 17 mg/MJ Fuel type wood pellets - 6mm dia. - complying with draft standard AS/NZS 4014.6 220 - 240 V Maximum Power Requirement 525W (1793 BTU/hr) Mean Flue Gas Temperature - High 188°C (370°F) Fuel Consumption - High 2.3 kg/hr (5.07 lb/hr)* Heat/Power Output - High 9.
Operating Instructions Control Board Functions: 7 AUGER 1 POWER 2 AUTO/OFF 3 HIGH/LOW MANUAL B 6 4 HEAT LEVEL A 5 ON/OFF 1. AUGER LIGHT: This green light will flash in conjunction with the auger pulse. 2. POWER LIGHT: Responsible for signaling the AUGER state of the control board. When the light is flashing the stove is in POWER an automatic start mode or the thermostat has control of the unit. When AUTO/OFFLevel Setting can be the light is solid, the Heat HIGH/LOW altered. MANUAL 3.
Operating Instructions 1 AUGER AUGER MANUAL MODE: 2 POWER POWER 7 All control of circuit board function is adjusted at the circuit board. AUTO/OFF AUTO/OFF To START: Press the ON / OFF button. HIGH/LOW The stove will turn 3 on. The HIGH/LOW system light will flash. The Auger Light will MANUAL flash with each pulse of the MANUAL auger (the Auger Feed Rate is pre-programmed during start-up).
Operating Instructions Slider/Damper Set-Up: The Slider / Damper must be set at time of installation. A Qualified Service Technician or Installer must set the Slider Damper. If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the firebox.
Routine Cleaning and Maintenance The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its optimum and giving you excellent heat value. The appliance, flue gas connector and the chimney flue require regular cleaning. Check them for blockage prior to re-lighting after a prolonged shut down period.
Routine Cleaning and Maintenance If the glass has build up that can not be removed with only the cloth, clean the glass using paper towel and a gas appliance glass cleaner, this may be purchased through most dealers. If a gas appliance glass cleaner is not available, use a damp paper towel dipped in fly ash to clean the glass. After the glass has been cleaned use the dry soft cloth to wiping down the outside and inside of the glass.
Routine Cleaning and Maintenance EXHAUST VENT (annually) Check vent for blockage prior to lighting after a prolonged shutdown period. This vent should be cleaned every year or after two tons of pellets. We recommend contacting your dealer for professional cleaning. For basic cleaning the vent pipe, tap lightly on the pipe to dislodge any loose ash. Open the bottom of the “T” to dump the ash, then vacuum as much of the ash out of the vent pipe as possible.
Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference.
