SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER. PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE PELLET STOVE Milan-A Fireplace Insert OWNER’S MANUAL Contact your building or fire officials about restrictions and installation inspection requirements in your area. PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER.
Table of Contents Introduction..............................................................................................................3 Rating Label Location......................................................................................3 Pellet Quality................. .................................................................................3 Safety Warnings & Recommendations..........................................................................4 Specifications.......................
Introduction * This manual is designed for the home owner in conjunction with the technical manual. * RATING LABEL LOCATION: The rating label is located on the hopper top behind the surround panel. PELLET QUALITY: Pellet quality is important, please read the following: Your Enviro pellet stove has been designed to burn 1⁄4” (6mm) dia wood pellets only. DO NOT use this appliance as an incinerator.
Safety Warnings & Recommendations Please read this entire Owner’s Manual before installing or operating your Enviro Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Any unauthorized modification of the appliance or use of replacement parts not recommended by the manufacturer is prohibited. All national and local regulations and shall be complied with when operating this appliance. Caution: Do not connect to any air distribution duct or system.
Safety Warnings & Recommendations ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 110-120 volts (4.1 Amps), 60 hertz electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power cord must be purchased from the manufacturer or a qualified Enviro dealer.
Specifications DIMENSIONS: 277/8" (708mm) 201/16" (510mm) 151/8" (383mm) 87/8" (226mm) 44" (1118mm) 305/16" (770mm) 307/8" (785mm) 151/16" (382mm) 2" (51mm) 30" (762mm) 1911/16" (500mm) 293/4" (756mm) Figure 1: Milan Dimensions. 251/4" (641mm) 3115/16" (812mm) 44" (1118mm) Figure 2: Dimensions of Milan with Optional Skirt.
Operating Instructions CONTROL BOARD FUNCTIONS: 1. THERMOSTAT SWITCH: Used to set the unit’s controls to one of three mode settings; manual, high/low, or auto/off. 2. FEED RATE TRIM BUTTON: Used to change the feed rate trims in 1⁄4 second increments for all feed settings. When this button is pressed, all the light will light up on the Heat Output Indicator except for the one that shows the current setting; the default setting is the 5 number 4 light.
Operating Instructions HIGH/LOW MODE: (Requires a thermostat) 5 INITIAL START-UP: See manual mode above. AUTO/OFF OPERATION: When the 4thermostat calls for heat (contacts are closed) HIGH 3 /LOW the stove settings are adjustable as per Manual Mode. When the 9 3 thermostat contacts open, the HEAT LEVEL and Fans will drop down to MANUAL the LOW setting until the thermostat contacts close again.
Operating Instructions SLIDER/DAMPER SETTING: This is used to regulate the airflow through the pellet stove. THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION. A Qualified Service Technician or Installer must set the Slider Damper. • If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be moved to the left slightly, lessen the air flow into the firebox.
Routine Cleaning and Maintenance The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its optimum and giving you excellent heat value: 2-3 Days / Weekly Burn Pot and Liner Door Latch Door Glass Ash pan and Door gaskets Ash Pan Heat exchanger Inside Firebox Semi-annually or 2 Tons of Fuel Fresh Air Intake Exhaust Passages Exhaust Vent Blower Mechanisms Behind firebox liners All Hinges Post Season Clean-up TOOLS REQUIRED TO CLEAN UNIT • T
Routine Cleaning and Maintenance ASH PAN AND DOOR GASKETS (weekly) After extended use the gasketing may come loose. To repair this, glue the gasketing on using hightemperature fiberglass gasket glue available from your local ENVIRO dealer. This is important to maintain an airtight assembly. ASH PAN (2-3 days) The ash pan is located under the door. To remove the ash pan, simply turn the latch with a large standard blade screwdriver and pull out towards the front.
Routine Cleaning and Maintenance EXHAUST VENT (season) This vent should be cleaned every year or after two (2) tons of pellets. We recommend contacting your dealer for professional cleaning. To clean the vent pipe, run a chimney cleaning brush through the pipe. Open the bottom of the “T” to dump the ash, then vacuum as much of the ash out of the vent pipe as possible. BLOWER MECHANISMS (season) Unplug the stove and pull out the unit to access the two blowers.
Warranty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the finest materials and is backed by our Exclusive Lifetime Limited Warranty to the original purchaser. With Enviro, you’re not just buying a stove, you’re buying a company with years of unequalled performance and quality.
Warranty Exclusions and Limitations: 1. This Warranty does not cover tarnish, discoloration or wear on the plating or paint. 2. This Warranty excludes wear and tear or breakage caused by cleaning, moving or service on log set. 3. A qualified installer must install this stove or fireplace. This Limited Warranty covers defects in materials and workmanship only if the product has been installed in accordance with local building and fire codes; in their absence, refer to the owner’s manual.
Warranty 17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warranty. 18. The Limited Warranty does not cover tarnish, discoloration or wear on the plated surfaces. 19. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint during normal usage. It is not a flaw and is not covered under warranty. 20.
Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference.
