Instructions / Assembly

ManualsBrandsEnviroLite ManualsLighting6 in. Selectable CCT Integrated LED White Canless Wafer With New Construction Mounting Frame, (6-Pack) Light Kit

Table Of Contents

PLASTER FRAME

INSTALLATION INSTRUCTIONS

MODEL EVMP6HBMJ2W-I

For use with Downlight Model DRF6WHWH9105C

Please read the instructions carefully and save these instructions, as you may

need them at a later date.

CAUTION

Turn power off at circuit breaker before beginning fixture installation to avoid

electrical shock.

GENERAL

All electrical connections must be in accordance with local and National

Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical

wiring connections obtain the services of a qualified electrician.

Remove the fixture and the mounting package from the box and make sure

that no parts are missing by referencing the illustrations on the installation

instructions.

JOIST INSTALLATION INSTRUCTIONS

1. Adjust the hanger bar length by separating the bars. [Fig. 1]

2. Position the frame between joists. Make sure that the hanger bars are in

the correct position. The bottom edge of the hanger bars should be level

with the bottom of the joists. [Fig. 2]

3. Nail the hanger bars to the joists. [Fig. 3]

4. Mark the opening for the hole of the frame on the ceiling. Use a keyhole

saw to cut the hole out. [Fig. 4]

5. Pull the quick connector down from hole. [Fig. 5]

6. Remove a knockout to bring the supply wires into the wire box. Connect

the black supply wire to the black frame wire using a wire connector.

Connect the white supply wire to the white frame wire using a wire

connector. Connect the ground supply wire to the ground frame wire using

a wire connector. [Fig. 6]

HANGING BAR INSTALLATION INSTRUCTIONS

1. Use pliers to bend the ends of the hanger bars. [Fig. 7]

2. Remove the ceiling grid panel.

3. Rotate the frame sideways to insert easily into the ceiling. Place the frame

in line with the ceiling grid.

4. Ensure the frame sits evenly inside the T-bar ceiling grid. Secure the

frame to the suspended ceiling grid by using pliers to secure the tabs on

the ends of the hanger bars. [Fig. 8]

5. Remove a knockout to bring the supply wires into the wire box. Connect

the black supply wire to the black frame wire using a wire connector.

Connect the white supply wire to the white frame wire using a wire

connector. Connect the ground supply wire to the ground frame wire using

a wire connector. [Fig. 6]

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Summary of content (8 pages)

PAGE 1
PLASTER FRAME INSTALLATION INSTRUCTIONS MODEL EVMP6HBMJ2W-I For use with Downlight Model DRF6WHWH9105C Please read the instructions carefully and save these instructions, as you may need them at a later date. CAUTION Fig. 1 Turn power off at circuit breaker before beginning fixture installation to avoid electrical shock. GENERAL Fig. 5 All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards.
PAGE 2
MARCO DE YESO INSTRUCCIONES DE INSTALACIÓN MODELO EVMP6HBMJ2W-I Para uso con luz DRF6WHWH9105C Por favor lea las instrucciones con cuidado y guarde las instrucciones, ya que puede necesitarlas después. PRECAUCIÓN Fig. 1 Desactive la electricidad del cortacircuitos antes de empezar la instalación de la luminaria para evitar una descarga eléctrica. GENERAL Fig. 5 Todas las conexiones eléctricas deben realizarse conforme al código eléctrico nacional y los códigos eléctricos locales.
PAGE 3
CADRE EN PLÂTRE GUIDE D’INSTALLATION MODÈLE EVMP6HBMJ2W-I À utiliser avec le modèle d'éclairage DRF6WHWH9105C Lire attentivement ce mode d’emploi et le conserver pour référence future. MISE EN GARDE Coupez l’alimentation électrique au panneau principal avant de commencer l’installation afin d’éviter tout risque d’électrocution. Fig. 1 GÉNÉRALITÉS Tous les raccordements doivent être effectués conformément aux exigences des règlements locaux et du code national de l’électricité (CNE).
PAGE 4
WARRANTY Envirolite warrants this product to be free from defects in material and workmanship for one years from the original date of purchase by the consumer. This warranty is limited to the counter replacement at the time of purchase, with the original purchase receipt.
PAGE 5
QUESTIONS? CALL TOLL FREE 1-855-573-6156 or EMAIL INFO@ENVIROLITE-LED.COM DOWNLIGHT INSTALLATION INSTRUCTIONS MODEL DRF6WHWH9105C For use with Plaster Frame Model EVMP6HBMJ2W-I Fig. 4 Please read the instructions carefully and save these instructions, as you may need them at a later date. CAUTION Turn power off at circuit breaker before beginning fixture installation to avoid electrical shock. GENERAL Fig. 1 Fig.
PAGE 6
¿PREGUNTAS? LLAME GRATIS 1-855-573-6156 o CORREO ELECTRÓNICO INFO@ENVIROLITE-LED.COM LUMINARIA EMPOTADA INSTRUCCIONES DE INSTALACIÓN MODELO DRF6WHWH9105C Para Uso con Marco de Yeso Modelo EVMP6HBMJ2W-I Fig. 4 Por favor lea las instrucciones con cuidado y guarde las instrucciones, ya que puede necesitarlas después. PRECAUCIÓN Desactive la electricidad del cortacircuitos antes de empezar la instalación de la luminaria para evitar una descarga eléctrica. GENERAL Fig. 1 Fig.
PAGE 7
DES QUESTIONS? APPELEZ SANS FRAIS 1-855-573-6156 ou COURRIEL INFO@ENVIROLITE-LED.COM PLAFONNIER GUIDE D’INSTALLATION MODÈLE DRF6WHWH9105C À utiliser avec le modèle du cadre au plafond EVMP6HBMJ2W-I Fig. 4 Lire attentivement ce mode d’emploi et le conserver pour référence future. MISE EN GARDE Coupez l’alimentation électrique au panneau principal avant de commencer l’installation afin d’éviter tout risque d’électrocution.
PAGE 8
FCC NOTICE AVISO DE LA FCC AVIS DE LA FCC ADVERTENCIA: Cambios o modificaciones a esta unidad no aprobados expresamente por la parte responsable del cumplimiento podrían anular la autoridad del usuario para operar el equipo. WARNING: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.