Installation Guide

FIVE-YEAR LIMITED WARRANTY
LiteChoice  warrants this product to be free from defects in material and
workmanship for five years from the original date of purchase by the
consumer. This warranty is limited to the counter replacement at the time
of purchase, with the original purchase receipt. LiteChoice  will not be
liable for the loss or damage of any kind, incidental or consequential
damages of any kind, whether based on warranty contract or negligence,
and arising in connection with the sale, use or repair of the product claimed
to be defective. Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation may not apply
to you. This warranty gives you specific legal rights and you may also
have other rights, which vary from state to state. Misuse, accident,
improper installation or maintenance will also void the warranty.
DIMMING
Dimming performance may depend on the dimmer, the dimmer range
adjustment setting (for dimmers with brightness range adjustments), the
wiring method, and/or the number of LED modules installed onto the
dimmer circuit.
For dimmer selection, it is recommended to use one of the following
dimmers:
• Leviton Decora SureSlide® – 6631, 6674 (Universal); Leviton
IllumaTech® - IPI06-1L, IPL06-10 (Universal)
• Lutron Ariandni®/Toggler® - TGCL-153P, AYCL-153P; Lutron Diva®
- DVWCL-153P, DVCL-153P; Lutron Luméa® - LGCL-153P, Lutron
Maestro® - MACL-153M; Lutron Skylark® - S-600, S-603P, SCL-
153P; Lutron Skylark Contour™ - CTCL-153P.
• For best results, it is recommended to install a minimum of four LED
modules onto one dimmer.
• Before turning on the LED lights, set dimmer position at maximum
before adjusting to a lower light level.
• Please follow the dimming control manufacturer’s instructions for the
installation of all dimming controls.
ALL RIGHTS RESERVED. COPYRIGHT  LITECHOICE 2014
LED DRIVER REPLACEMENT
NOTE: First turn off electricity at the circuit breaker or the fuse box.
Turning the power off by using a wall switch is not sufficient to prevent
electrical shock.
1. Pull the EasyUp™ Trim down from the ceiling. (NOTE: When pulling
the trim down, the spring-loaded wings will flip down forcefully. To
prevent the spring-loaded wings from hitting one’s fingers, partially
pull down the trim about 1” to locate the spring-loaded wings. Push
the trim back into the ceiling. Reposition fingers away from the
spring-loaded wings and pull down the entire trim so that the spring-
loaded wings flip down and the trim hangs about 6” to 8” from the
ceiling.)
2. Open the top door of the junction box. Disconnect wire connections
by removing wire connectors.
3. Using a flathead screwdriver, carefully pry open any strain relief slot
tab to remove its NM cable. Remove all NM cables.
4. Remove the decorative magnetic ring. Using a flathead screwdriver,
push out the lens tabs located on the side of the heat sink.. This will
detach the lens from the heat sink, allowing access to the LED board.
5. Detach wire connector from LED board. (Fig. 6)
TROUBLESHOOTING
If a voltage is measured, then LED
driver is working. Replace LED board.
If no voltage is measured, then replace
LED driver.
If a voltage is fluctuating, then replace
LED driver.
If a constant voltage is measured, then
LED driver is working. Replace LED
board.
Lights flicker during
dimming
Check if dimmer being used is
in compatible dimmer list from
"DIMMER" section
If dimmer is not on list, replace dimmer
from the list
If wiring connections are loose or
disconnected, redo connections. Make
sure that there are no exposed wire
conductors.
If wiring connections are good, the trim
may be defective and will need to be
replaced.
Lights flicker
Lights do not come on
at all
Disconnect LED driver
connector from LED board.
Using a volt meter, measure
LED driver open-circuit output
voltage.
Disconnect LED driver
connector from LED board.
Using a volt meter, measure
LED driver open-circuit output
voltage.
Fuse blows or circuit
breaker trips when
light is turned on
Check wire connections inside
the junction box
SYMPTOM ACTION SOLUTION
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Install the product onto on a circuit different from that to which the
receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for
help.
CAUTION: Any changes made to the electronics circuit will void this
equipment’s compliance with Part 15 of the FCC Rules and should not be
operated.
LED
board
Wire
connector
6. Remove the two screws located inside the junction box. Lift off the
junction box from the LED driver. Remove the two mounting screws
securing the LED driver to the heat sink. Lift off the LED driver from
the heat sink, while pulling its output wires and wire connector
through the heat sink hole. Discard the LED driver.
7. Insert the output wires and wire connector of the new LED driver into
the heat sink hole and push them into the LED compartment.
Connect the wire connector to the LED board. (Fig. 6)
8. Replace the lens back onto the heat sink. Replace the decorative
magnetic ring.
9. Replace the new LED driver onto the heat sink using the previously
removed mounting screws. Replace the junction box onto the new
LED driver using the previously removed screws.
10. Starting on Step 4, follow the steps in the “INSTALLING THE
FIXTURE” section to complete the reinstallation. (NOTE: Reuse the
wire connectors removed in Step 2 for Step 5 of the “INSTALLING
THE FIXTURE” section.)
White
reflector
LED board
mounting
screw
Fig. 6