Installation Guide

ManualsBrandsEnviroLite ManualsLightingEasy Up with Direct Wire J-Box 6 in. White Integrated LED Recessed Kit, 2700K

Ceiling

Cable

Hole

Fig. 2

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT

MAIN POWER AT FUSE OR CIRCUIT BREAKER

BEFORE INSTALLING OR SERVICING THE FIXTURE.

LED 6” RECESSED TRIM INSTALLATION

INSTRUCTIONS – MODEL EV608943

Please read carefully and save these instructions,

as you may need them at a later date.

GENERAL: All electrical connections must be in accordance with local and

National Electrical Code (N.E.C.) standards. Be sure to read these

instructions and review the diagrams thoroughly before beginning. If you are

unfamiliar with proper electrical wiring connections obtain the services of a

qualified electrician.

BEFORE YOU BEGIN

1. Check if the power source is suitable for the added electrical load.

Power should be supplied by a 110/120 volt, 60 Hz single circuit. A

standard 120 volt, 15 amp branch circuit is designed to carry a

maximum load of 1800 watts. We recommend that the total wattage of

all the lights and appliances on that circuit, not exceed 80% or 1440

watts, of the maximum electrical capacity.

2. This fixture is an IC type fixture. It may come in direct contact and

be completely covered with thermal insulation that has an R-value

of 3.85 or less. Some insulation types that meet this requirement

are blanket batting/roll and blown-in loose fill. Do not install in a

ceiling with spray foam type insulation. Any part of the fixture may

come in direct contact with any combustible material, such as a ceiling

joist or floor board.

3. This fixture requires an existing ceiling surface, such as drywall, for

installation. To install this fixture, a hole needs to be made into the

ceiling surface at the desired location. Then, power supply wiring (NM

cable) needs to be installed from the power source to the hole.

4. This fixture is designed for ceiling surfaces that are 3/4” thick or less.

Do not use this fixture on ceiling surfaces that are thicker than ¾”.

5. This fixture may be installed over a wet or damp location such as a

shower stall or bathtub enclosure. The area above the ceiling surface

must, however, be a dry location.

6. To prevent wiring damage or abrasion, do not expose wiring to edges

of sheet metal or other sharp objects.

UNPACK THE FIXTURE

Check the contents of the box. You should have:

• 1 – Fixture

• 1 – Hole Template (6 ¼ ” diameter)

• 3 – Wire Connectors

INSTALLING THE FIXTURE

NOTE: First turn off electricity at the circuit breaker or the fuse box. Turning

the power off by using a wall switch is not sufficient to prevent electrical

shock.

1. Choose the location for the fixture, taking into consideration the 6”

depth clearance requirement, the location of ceiling joists and the

accessibility for the electrical supply. Mark the selected location with a

circle using the provided template.

2. Using a keyhole saw make a 6 ¼ ” hole in the ceiling surface. (Fig. 1)

(Note: Be sure not to make the hole any larger than specified by the

template. An oversized hole may not allow for proper installation.)

3. Run non-metallic (NM) cable (also known as Romex) or an armored

cable (also known as BX) from your circuit breaker or fuse panel to

the hole, providing 6” (15,2 cm) to 8” (20,3 cm) of slack extending

below the hole. Cable having up to 12 AWG wiring may be used. (Fig.

2) (WARNING - Use cables having wires rated 90°C or more.)

4. Open the side door of the junction box. If you are using a BX cable,

remove one of the round knockouts located on the top or sides of the

junction box. If you are using NM cable, remove a rectangular

knockout on the back of the junction box. Insert about 5 or 6 inches of

the NM cable into the junction box through one of the provided strain-

relief slots. (Fig. 3)

5. Remove at least 3” of the cable’s outer sheath and remove the plastic

or paper over-wrap. Strip approximately 3/8” of insulation from the

ends of all supply wires. Using the wire connectors, make the

following wire connections within the junction box (Fig. 3):

WHITE Fixture Wire to WHITE (NEUTRAL) Supply Wire

BLACK Fixture Wire to BLACK (HOT) Supply Wire

Fixture GROUND Wire to Supply GROUND Wire

6. Carefully stuff the wires and the wire connections into the junction box.

Close the junction box top door. Tighten the fastening screw.

7. Raise the fixture up to the ceiling hole, while simultaneously pushing

the excess NM cable into the hole. (Fig. 4)

8. Flip up and squeeze the spring-loaded wings against the junction box,

as shown, and insert the fixture into the hole, junction box first. (Fig. 4)

Strain-relief

slot

Side Door

Wire

connector

Junction

Box

Fig. 3

Fig. 1

Ceiling joist

Ceiling

EV608943

EV407943

CER407943

QUESTIONS? CALL THE

TOLL-FREE NUMBER

LOCATED ON THE PACKAGE

Summary of content (6 pages)

PAGE 1
LED 6” RECESSED TRIM INSTALLATION INSTRUCTIONS – MODEL EV608943 QUESTIONS? CALL THE TOLL-FREE NUMBER LOCATED ON THE PACKAGE WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE. Please read carefully and save these instructions, as you may need them at a later date. GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards.
PAGE 2
FIVE-YEAR LIMITED WARRANTY NM or BX cable Hole Junction Box Fig. 4 ___________________________________________________________ Spring-loaded wing 9. This product is warranted to be free from defects in material and workmanship for five years from the original date of purchase by the consumer. This warranty is limited to the counter replacement at the time of purchase, with the original purchase receipt.
PAGE 3
INSTRUCCIONES DE INSTALACIÓN DEL ADAPTADOR DECORATIVO LED 6” – MODELO EV608943 Por favor, lea cuidadosamente y guarde estas instrucciones, ya que puede necesitar en una fecha posterior. ¿PREGUNTAS? LLAME GRATIS AL NÚMERO QUE APARECE EN EL EMBALAJE WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE.
PAGE 4
6. 7. 8. Coloque con cuidado los cables y las conexiones de los cables dentro de la caja de conexiones. Cierre la puerta superior de la caja de conexiones. Apriete el tornillo de fijación. Levante la luminaria empotrable hasta el agujero del techo, mientras simultáneamente empuja el cable en exceso NM en el agujero. (Fig. 4) Levante y apriete las alas de resorte contra la caja de conexión, como se muestra, e inserte la luminaria empotrable en el agujero, empezando con la caja de conexiones. (Fig.
PAGE 5
MODE D’INSTALLATION DE LA GARNITURE DEL DE 6 PO MODÈLE – EV608943 DES QUESTIONS? APPELEZ LE NUMÉRO SANS FRAIS INDIQUÉ SUR L’EMBALLAGE AVERTISSEMENT: RISQUE D'ÉLECTROCUTION. COUPEZ L’ALIMENTATION ÉLECTRIQUE AU NIVEAU DU FUSIBLE OU DU DISJONCTEUR AVANT D’INSTALLER OU DE RÉPARER LE LUMINAIRE. Veuillez lire attentivement ces instructions et les conserver pour pouvoir vous y référer au besoin. .
PAGE 6
. 7. 8. Rentrez soigneusement tous les fils et les connecteurs dans la boîte de jonction. Fermez le couvercle supérieur de la boîte de jonction. Serrez la vis de fixation. Soulevez le luminaire encastré vers l’ouverture du plafond, tout en poussant l’excédent de câble NM dans l’ouverture. (Fig.