Instructions / Assembly

ManualsBrandsEnviroLite ManualsLighting6 in. IC Rated LED New Construction Recessed Housing

READ ALL THE INSTRUCTIONS

TRIM COMPATIBILITY

6” LED NEW CONTRUCTION AIRTIGHT

IC-RECESSED HOUSING INSTALLATION

INSTRUCTIONS – MODEL EVR6SLICATB, EVR6LICATB

QUESTIONS? CALL TOLL

FREE 1-855-573-6156

5. This product has a special feature, which secures the NM

USE ONLY WITH THE FOLLOWING MODELS:

LiteChoice: 9Y6WHWH-4Cxx, 1F6WHWH-2Cxx, 9Y6WHWH-2Cxx,

1G6SCWH-29xx, 1D6WHWH-2Cxx

Commercial Electric: CER6730, CER6041, CER6741, CER6742,

CER6732DB, CER6732DS

EnviroLite: EVL6730, EVL6041, EVL6741, EVL6742, EVL6732DB,

EVL6732DS

TOOLS & MATERIALS REQUIRED

(Romex) cable to the junction box, in lieu of a cable connector.

This feature will not work with BX (armored) cable. For BX

cable, cable connectors need to be purchased separately. See

the “ELECTRICAL CONNECTIONS” section.

6. This is a new-construction fixture. This new-construction

fixture can be installed in applications where the ceiling surface

has yet to be installed and the ceiling joists are exposed, such

as when a home is under new construction. If a ceiling surface

already

exists

and

there

access

above

the

ceiling

surface,

TOOLS

MATERIALS

REQUIRED

Ladder, BX or NM Cable, BX Cable Connectors (if necessary),

Keyhole Saw, Flathead Screwdriver, Hammer, Insulated Pliers,

Pencil, UL Listed Electrical Tape.

CAUTION

Before assembling your lighting fixture, refer to the section titled

ELECTRICAL CONNECTIONS. If you feel you do not have

electrical wiring experience, refer to a do-it-yourself wiring handbook

have

your

fixture

installed

qualified

licensed

electrician

already

exists

and

there

access

above

the

ceiling

surface,

do not use this fixture. A remodel fixture is recommended,

instead. This fixture may also be installed onto a drop ceiling,

where there is a standard T-bar grid in place.

UNPACK THE FIXTURE

Check the contents of the box. You should have:

1 - Housing/Hanger Bar Assembly, 1 - Cardboard Circular Template,

3 - “Quick-Connect” Wire Connectors (inside junction box)

have

your

fixture

installed

qualified

licensed

electrician

NOTE: This fixture is an IC type fixture. It may come in direct

contact with thermal insulation. It can be completely covered

by thermal insulation, as shown below. In addition, any part of

the fixture may come in direct contact with any combustible

material, such as a ceiling joist or floor board. (FIG. 1)

PREPARING AND MOUNTING THE FIXTURE

HANGER BAR PREPARATION

The hanger bars are designed for joists that are spaced 16” to 24”

(center to center) apart. If the joists are less than 16” apart, the

hanger bars must be shortened to accommodate the narrower

space. To shorten them:

1. Remove the han

bars from the

laste

frame. This ma

NOTE: Insulation

may completely

cover fixture.

FIG. 1

Joist

Fixture

Insulation

require opening the guides of the plaster frame using pliers.

2. Spread the bars as wide as possible. (FIG. 2)

3. For each hanger bar, bend the “male” bar, back and forth at the

crease from the center until it splits. Bend the “female” bar,

back and forth, at the 1st notch from the center until it splits.

(FIG. 2)

FIG. 2

Crease –

Bend Here

Notch –

Bend Here

“

Male

”

Bar

“Female” Bar

BEFORE YOU BEGIN

1. To ensure the success of the installation, be sure to read these

instructions and review the diagrams thoroughly before

beginning.

2. All electrical connections must be in accordance with local code,

f ili

i lli

4. Slide the “male” and “female” bars together and determine if the

hanger bar has been shortened enough. If not, separate the

“male” and “female” bars and break off additional material at the

next crease and notch. Continue to break off material until

proper length is achieved. Do not break off any more material

Male

Bar

nances.

you are un

ili

met

nsta

lli

electrical wiring, secure the services of a qualified licensed

electrician.

3. Before starting the installation, disconnect electricity at the circuit

breaker or the fuse box. Disconnecting power by using the wall

switch is not sufficient to prevent electrical shock.

4. Check if the power source is suitable for the added electrical

load. Powe

should be su

lied b

a 110/120 volt

60 Hz sin

an necessar

5. Once proper length is achieved, separate the “male” and

“female” bars. Slide the “female” bars into the guides of the

plaster frame. Slide the “male” bars into the “female” bars.

circuit. A standard 120 volt, 15 amp branch circuit is designed to

carry a maximum load of 1800 watts. We recommend that the

total wattage of all the lights and appliances on that circuit, not

exceed 80% or 1440 watts, of the maximum electrical capacity.

Summary of content (9 pages)

PAGE 1
6” LED NEW CONTRUCTION AIRTIGHT IC-RECESSED HOUSING INSTALLATION INSTRUCTIONS – MODEL EVR6SLICATB, EVR6LICATB QUESTIONS? CALL TOLL FREE 1-855-573-6156 READ ALL THE INSTRUCTIONS TRIM COMPATIBILITY 5.
PAGE 2
CEILING JOIST INSTALLATION NOTE: This fixture can be installed into a ¾” thick furring strip, using the pre-attached fast nails at the end of each hanger bar. 1. Choose the location for the fixture, taking into consideration the required 7” clearance and the accessibility to the electrical supply. 4. Place the housing and ceiling tile back into the drop ceiling. Tightent the mounting flanges around each T-Bar to secure the housing in place (FIG. 7). 5. Proceed to the “ELECTRICAL CONNECTIONS” section.
PAGE 3
When using the “quick-connect” wire connectors, be sure that there are no loose/exposed wire strands. Wrap each wire connection using UL Listed electrical tape. Flathead Screwdriver Pry out knockout FIG. 8 FIG. 11 FIG. 10 Male connector Housing Female connector C-bracket Rectangular Knockout Torsion spring arms LED trim NM Cable (ROMEX) _____________________________ FIVE-YEAR LIMITED WARRANTY Slide NM cable into locking slot Round Knockout FIG.
PAGE 4
¿PREGUNTAS? LLAMA GRATIS AL 1-855-573-6156 CARCASA HERMÉTICA DE LÁMPARA DE 15,2 cm (6 in.
PAGE 5
INSTALACIÓN EN VIGAS DEL TECHO NOTA: Este accesorio se puede instalar en una tira de enrasado de ¾ ”de grosor, utilizando los clavos rápidos preinstalados al final de cada barra de suspensión. 1. Elige el lugar para la lámpara, sin olvidar que se necesitan 17,8 cm de holgura y acceso al suministro eléctrico. 2. Alza ensamblaje de la carcasa/barra para colgar hasta la posición deseada entre las dos vigas g del techo. Ajusta j el ancho de las dos barras para colgar según la distancia entre las vigas.
PAGE 6
Asegúrate de que no haya hilos sueltos o expuestos cuando uses los conectores de cable “quick-connect”. Envuelve cada conexión con cinta aislante con clasificación UL. FIG. 10 FIG. 11 Caja Destornillador de Cabeza Plana Abrir entrada Conector macho FIG. 8 Soporte receptore Conector hembra Entrada Rectangular Brazos del resorte de torsión Moldura FIG.
PAGE 7
LUMINAIRE ENCASTRÉ DE HERMÉTIQUE DE 15,2 CM POUR NOUVELLE CONSTRUCTION (PLAFOND ISOLÉ) POUR GARNITURE À DEL MODE D’INSTALLATION – MODELE EVR6SLICATB & EVR6LICATB LISEZ TOUTES LES INSTRUCTIONS COMPATIBILITÉ DE LA GARNITURE UTILISER SEULEMENT AVEC LES MODÈLES SUIVANTS: SUIVANTS LiteChoice: 9Y6WHWH-4Cxx, 1F6WHWH-2Cxx, 9Y6WHWH-2Cxx, 1G6SCWH-29xx, 1D6WHWH-2Cxx Commercial Electric: CER6730, CER6041, CER6741, CER6742, CER6732DB, CER6732DS EnviroLite: EVL6730, EVL6041, EVL6741, EVL6742, EVL6732DB, EVL6732DS OUTILS
PAGE 8
4. Glissez les sections « mâles » et « femelles » l’une dans l’autre pour vérifier si la barre de suspension a été suffisamment raccourcie. Au besoin, séparez de nouveau les deux sections et raccourcissez chacune d’entre elles à la prochaine rainure ou encoche, jusqu’à ce que vous obteniez la longueur désirée. Prenez garde de ne pas trop raccourcir la barre. 5. Lorsque vous avez obtenu la longueur désirée, séparez les sections « mâles » et « femelles ».
PAGE 9
2. 3. Ouvrez le couvercle de la boîte de jonction en soulevant le loquet de métal. A. CÂBLE BX (ARMÉ) : Enfoncez une des rondelles défonçables (FIG. 9) à l’aide d’un tournevis. Fixez un connecteur de câble BX de taille adéquate dans l’ouverture de l’entrée défonçable. Passez le câble BX dans le connecteur, en laissant dépasser une longueur de 15,3 cm à l’intérieur de la boîte de jonction. Serrez le connecteur pour fixer le câble en place place. B.