Instructions / Assembly

ManualsBrandsEnviroLite ManualsLighting4.33 ft. 6-Light Black Integrated LED Track Lighting Kit with Adjustable Bar and 6-Rotating Track Heads

EVT61047D-05

6 LIGHT LED FIXED TRACK

Questions, problems, missing parts? Before returning to the store,

call Envirolite Customer Service

8 a.m. – 6 p.m., EST, Monday – Friday

1-855-573-6156

WARRANTY

WHAT IS COVERED

The manufacturer warrants this lighting fixture to be free from defects in

materials and workmanship for a period of five (5) years from date of

purchase. This warranty applies only to the original consumer purchaser and

only to products used in normal use and service. If this product is found to be

defective, the manufacturer’s only obligation, and your exclusive remedy, is

the repair or replacement of the product at the manufacturer’s discretion,

provided that the product has not been damaged through misuse, abuse,

accident, modifications, alterations, neglect or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been

improperly installed, set-up, or used in any way not in accordance with the

instructions supplied with the product. This warranty shall not apply to a failure

of the product as a result of an accident, misuse, abuse, negligence,

alteration, or faulty installation, or any other failure not relating to faulty

material or workmanship. This warranty shall not apply to the finish on any

portion of the product, such as surface and/or weathering, as this is

considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any warranty,

whether expressed or implied, of fitness for a particular purpose, other than

the warranty contained herein. The manufacturer specifically disclaims any

liability and shall not be liable for any consequential or incidental loss or

damage, including but not limited to any labor/expense costs involved in the

replacement or repair of said product.

FCC NOTICE

This device has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interface by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the device and receiver.

 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

PACKAGE CONTENTS

NOTE: Contents are not shown to size.

Part

Description

Qty

Track Light

Thumb Nut

Wire

Nut 3

Mounting Screw

Nipple

SAFETY INFORMATION

WARNING: Disconnect the power prior to removing or installing a light fixture.

 Before installing this fixture or removing a previous fixture, disconnect the

power by turning off the circuit breaker or by removing the fuse at the

fuse box.

 Consult a qualified electrician if you have any electrical questions or

need to replace the driver.

 If you have any non-electrical questions about this fixture, please contact

our Customer Service Team at 1-855-573-6156.

PLANNING THE INSTALLATION

NOTE: Keep your receipt and these instructions for proof of purchase.

Read all instructions before assembling and installation your fixture. Before

installing the fixture or removing a previous fixture, disconnect the power by

turning off the circuit breaker or by removing the fuse at the fuse box. To avoid

damaging this product, assemble it on a soft, non-abrasive surface such as

carpet or cardboard.

TOOLS REQUIRED

BB CC DD

FF GG HH II

Safety

Goggles

Ladder

Electrical

Tape

Wire

Cutter

Wire

Stripper

Phillips

Screwdriver

Flathead

Screwdriver

Hammer Drill

1/4” Drill

Bit

Pencil

Part

Description

Qty

Fixture Screw

Ceiling

Anchor 2

Anchor

Screw 2

Mounting Bracket

Summary of content (4 pages)

PAGE 1
SAFETY INFORMATION WARNING: Disconnect the power prior to removing or installing a light fixture.  Before installing this fixture or removing a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.  Consult a qualified electrician if you have any electrical questions or need to replace the driver.  If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-855-573-6156.
PAGE 2
INSTALLATION INSTRUCTIONS OPERATION STEP 1  Thread the fixture screws (FF) through the holes in the tabs of the mounting bracket (II).  Pull the power supply wires out from the outlet box.   Turn on the power at the circuit breaker or fuse box.  Turn the light switch on to activate the fixture. CARE & CLEANING II Mount the mounting bracket (II) to the outlet box using the mounting screws (DD). NOTE: Do not use any cleaners with chemicals, solvents, or harsh abrasives.
PAGE 3
INFORMACIÓN DE SEGURIDAD ADVERTENCIA: Desconecte la alimentación antes de remover o instalar un luminario. EVT61047D-05 RIEL FIJO CON 6 LUCES LED  Antes de iniciar la instalación de este aparato o la eliminación de un accesorio anterior, desconecte la alimentación apagando el disyuntor o quitando el fusible en la caja de fusibles.  Consulte a un electricista calificado si tiene alguna pregunta eléctrica o la necesidad de reemplazar el controlador.
PAGE 4
INSTRUCCIONES DE INSTALACIÓN OPERACIÓN PASO 1  Enrosque los tornillos del luminario (FF) por medio de los agujeros en las lengüetas de la ménsula de montaje (II).  Conecte la alimentación en el disyuntor o caja de fusibles.  Gire el interruptor de la luz para activar el aparato. CARE & CLEANING  Saque los cables de alimentación de la caja de alimentacion. II  Monte la ménsula de montaje (II) sobre la caja de alimentacion utilizando los tornillos de montaje (DD).