Instructions / Assembly

ManualsBrandsEnviroLite ManualsCommercial Lighting223-Watt 4 ft. White Integrated LED Backlit High Bay Hanging Light with 29,213-Lumens

____________________________

ASSEMBLY AND INSTALLATION

1. Remove the screw (A) near the wire cover (B)

located on the back of the fixture. [Fig. 1]

2. Punch out one of the knockouts (C) in the wire

cover (B). [Fig. 1]

3. Open the wire cover (B) and thread the supply

wires through the knockout (C). Insert the

supply wires into the quick connector (D)

aligning the black supply wire with the black

fixture wire and the white supply wire to the

white fixture wire. [Fig. 2]

4. If the fixture will be connected to a dimmer, punch

out one of the knockouts (E) located around the

back portion of the fixture and pull the dimming

wires out through that knockout (E). [Fig. 3]

5. Place the wire cover (B) back onto the fixture

and secure it with the screw (A) that was

previously removed. [Fig. 1]

6. Hook the hangers into the oblong holes in the

back of the fixture and through the round holes

on the end of the fixture. [Fig. 4]

________

DIMMING

1. Insert the purple dimming wire into the quick

connecter with the purple fixture wire. Insert

the grey dimming wire into the quick

connector with the grey fixture wire. [Fig. 5]

For up-to-date list of compatible dimmers, look

up the model number at envirolite-LED.com.

4FT LED HIGH BAY, 223W, 5000K , MV, 0-10V DIMMING

INSTALLATION INSTRUCTIONS

Please read carefully and save these instructions. Failure to do so may lead

to electrical shock or fire, which may cause injury or death.

For questions, problems, or missing parts call the Customer Service line at

(866) 992-2278 from 8 AM to 6 PM EST Monday – Friday.

________

CAUTION

WARNING – RISK OF FIRE: Turn off the main power at the circuit breaker

before installing the fixture or performing other maintenance in order to

prevent possible shock.

_________

GENERAL

All electrical connections must be in accordance with local, and national

electrical codes.

Prior to installation remove all protective plastic film covering from the fixture.

Tools needed for installation: Phillips screwdriver, wire strippers, and

pliers.

Fig. 2

Fig. 1

Fig. 3

Fig. 5

Fig. 4

Summary of content (3 pages)

PAGE 1
____________________________ ASSEMBLY AND INSTALLATION 4FT LED HIGH BAY, 223W, 5000K , MV, 0-10V DIMMING 1. Remove the screw (A) near the wire cover (B) located on the back of the fixture. [Fig. 1] 2. Punch out one of the knockouts (C) in the wire cover (B). [Fig. 1] Fig. 1 3. Open the wire cover (B) and thread the supply wires through the knockout (C).
PAGE 2
ALTA BAHÍA LED DE 4 PIES, 223W, 5000K, MV, ATENUACIÓN DE 0-10V _______________________ MONTAJE E INSTALACIÓN 1. Retire el tornillo (A), cerca de la tapa de cable (B) situado en la parte posterior del luminario. [Fig. 1] 2. Perfore una de las entradas (C) en la placa de acceso (B). [Fig. 1] Fig. 1 3. Abra la placa de acceso (B) y enrosque los cables de alimentación a través de la entrada (C).
PAGE 3
HAUTE BAIE DEL DE 4 PIED, 223W, 5000 K, MV, 0-10V GRADATION _____________________________ ASSEMBLAGE ET INSTALLATION 1. Retirer la vis (A) près de la plaque d‘accès (B) située à l’arrière de le luminaire. [Fig.1] 2. Découper un des entrées (C) dans la plaque d‘accès (B). [Fig.1] 3. Ouvrez la plaque d‘accès (B) et passer les fils d’alimentation par le entrée (C).