Instructions / Assembly

ManualsBrandsEnviroLite ManualsCommercial Lighting8 ft. 870-Watt Equivalent Integrated LED White Strip Light Fixture, 4000K

Fig. 3

Fig. 1

MODEL ST8L117DMD40

INSTALLATION INSTRUCTIONS

Please read carefully and save these instructions. Failure to

do so may lead to electrical shock or fire, which may cause

injury or death.

________

CAUTION

WARNING – RISK OF FIRE: Turn off the main power at the

circuit breaker before installing the fixture, changing lamps,

or performing other maintenance in order to prevent possible

shock.

_________

GENERAL

All electrical connections must be in accordance with local,

and national electrical codes.

Prior to installation remove all protective plastic film covering

from the fixture.

Tools needed for installation: Phillips screwdriver, pliers.

_____________________________

ASSEMBLY AND INSTALLATION

1. Center the fixture on the outlet box. Mark the location of the

keyhole slots of the fixture onto the ceiling. Remove the

fixture from the ceiling.

Note: If the fixture does not sufficiently cover the outlet box,

screw in the semi-circular junction box covers on the back of

the fixture. (Fig. 3)

2. Align the ceiling anchors to the keyhole slot markings on the

ceiling and screw a mounting screw into the center opening.

Then repeat with the second ceiling anchor 88.5 inches

away. (Fig.1)

3. Place the fixture over the outlet box and slide the fixture so

that the ceiling anchor snaps into the narrow ends of the

keyhole slots and is secured flush against the ceiling. (Fig. 2)

4. Pull the power supply wires out from the outlet box.

Connect the black supply wire to the black fixture wire

using a wire nut. Connect the white supply wire to the

white fixture wire using a wire nut. Connect the fixture

ground wire and the supply ground wire together using

a wire nut. Wrap all wire connections with electrical tape

for a more secure connection. (Fig. 4)

________

DIMMING

1. Pull wires from light fixture hole, the dimming wires will be

wrapped around the power supply wires. (Fig. 6) Connect

the purple and pink/grey fixture wires to corresponding

wires of the wall dimmer. (Fig. 5)

For up-to-date list of compatible dimmers, look up the item

number at www.envirolite-LED.com.

Fig. 2

BLACK FIXTURE WIRE BLACK SUPPLY WIRE

WHITE FIXTURE WIRE WHITE SUPPLY WIRE

FIXTURE GROUND WIRE SUPPLY GROUND WIRE

Fig. 4

PURPLE FIXTURE WIRE PURPLE DIMMER WIRE

PINK/GREY FIXTURE WIRE PINK/GREY DIMMER WIRE

Fig. 5

Fig. 6

Summary of content (3 pages)

PAGE 1
_____________________________ ASSEMBLY AND INSTALLATION 1. Center the fixture on the outlet box. Mark the location of the keyhole slots of the fixture onto the ceiling. Remove the fixture from the ceiling. Fig. 1 Note: If the fixture does not sufficiently cover the outlet box, screw in the semi-circular junction box covers on the back of the fixture. (Fig. 3) MODEL ST8L117DMD40 2. Align the ceiling anchors to the keyhole slot markings on the ceiling and screw a mounting screw into the center opening.
PAGE 2
________________________ MONTAJE E INSTALACIÓN 1. MODELO ST8L117DMD40 INSTRUCCIONES DE INSTALACIÓN Por favor lea atentamente y guarde estas instrucciones. El no hacerlo puede causar una descarga eléctrica o un incendio, lo que puede causar lesiones o muerte. ____________ PRECAUCIÓN ADVERTENCIA - RIESGO DE INCENDIOS: Apague el interruptor principal en el disyuntor antes de instalar el aparato, cambiar las lámparas, o realizar otras tareas de mantenimiento a fin de evitar posibles descargas eléctricas.
PAGE 3
______________________________ ASSEMBLAGE ET INSTALLATION Fig. 1 1. Centrer le luminaire sur la boîte de sortie. Marquez l'emplacement des trous de serrure de le luminaire sur le plafond . Retirer le luminaire du plafond. Remarque: Si les appareils ne couvre pas suffisamment de la boîte de sortie, visser dans les couvertures de boîte de jonction semi-circulaire sur le dos de l'appareil. (Fig. 3) MODÈLE ST8L117DMD40 2.