EN-775e EN-775e 17 inch Flat CRT Color Monitor User’s Manual by Envision Peripherals, Inc. www.ENVISIONmonitor.com.com Before operating your monitor, please read this manual thoroughly.
For Your Safety EN-775e FCC Statement Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
For Your Safety Precautions EN-775e • The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. As a safety feature, this plug will only fit into a grounded power outlet. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. • Do not use the monitor near water, e.g.
For Your Safety General Notes General Features: • Do not install the monitor near heat sources such as radiators or air ducts. • 17" (43.2 cm) Color Monitor EN-775e • Crisp, Clear Display for Windows • Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock. • Supports Resolutions up to 1280 X 1024 pixels @60Hz • EPA ENERGY STAR® • Save the original shipping carton and packing materials in case you need to ship your monitor.
Before You Operate the Monitor EN-775e Installing & Removing the Base EN-775e 5 31MY02
Before You Operate the Monitor EN-775e Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Caution: Make sure the power cord is the correct type that is required in your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). 2.
Before You Operate the Monitor EN-775e Connecting the Wires Using An Optional Power Cord (Not Supplied) Follow these steps: The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws.
Operating Instructions EN-775e Front Panel Buttons Exit: Press this button to save changes and close the OSD window. MENU: Press this button to open the OSD window or select a highlighted function. Brightness: Press this button to adjust the picture’s brightness. If the OSD window is open, this button allows you to move within the window and select desired functions. Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode.
Operating Instructions EN-775e Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 5. To save and exit, press the EXIT icon or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. 2. Press the < or > buttons until the desired function is highlighted. Note: When the OSD window is open, the input signal timing settings appear at the top. H: stands for horizontal frequency and V: stands for vertical frequency. 3.
Operating Instructions EN-775e Plug & Play DDC1/2B Feature Windows INF Driver File This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. Most computers will automatically configure your monitor to work with your computer.
Technical Support (FAQ) Problem EN-775e Possible Solution Power LED is not ON • Make sure the power button is ON. • Make sure the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play • Confirm that your computer is Plug & Play compatible. • Confirm that your video card is Plug & Play compatible. • Inspect the video cable and make sure that none of the pins are bent.
Appendix EN-775e Specifications CRT Size Input 17.0" (43.2 cm) 11.4” (29 mm) neck 0.21mm(H), 0.25mm(D) dot pitch 90 degree deflection Viewable image size 16.0” (40.6 cm) diagonal Preset Display area 11.8” (300 mm) X 9.1” (230 mm) Dot Clock 110 MHz Maximum Resolution 1280 x 1024 pixels Plug & Play VESA DDC1/2B TM EN-775e 12 Video Red, Green, Blue Analog Interface Separate Sync. H/V TTL H/V Sync.
Appendix EN-775e Specifications (continued) Environmental Considerations Operating Temp: 32° to 104°F (0° to 40°C) ambient Operating Humidity: 10% to 90% Signal Cable Attached Mini D-sub 15 Male Optimal Viewing Mode: 1024 x 768 x 85 Hz EN-775e 13 31MY02
Appendix EN-775e Factory Preset Timing Table Standard VGA VESA / 85 VESA / 60 EN-775e Resolution (in pixels) Horizontal Frequency Vertical Frequency 720 × 400 31.5KHz 70 Hz 640 × 480 31.5KHz 60 Hz 640 x 480 43.3KHz 85Hz 800 x 600 53.7KHz 85Hz 1024 x 768 68.7KHz 85Hz 1280 × 1024 64.
Appendix EN-775e Connector Pin Assignment Pin Number EN-775e Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground 15 31MY02