EN-5200e EN-5200e 15 inch TFT LCD Monitor User’s Manual by Envision Peripherals, Inc. www.ENVISIONmonitor.com Before operating your monitor, please read this manual thoroughly.
For Your Safety EN-5200e FCC Statement Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
For Your Safety Precautions • The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. As a safety feature, this plug will only fit into a grounded power outlet. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. • Do not use the monitor near water, e.g.
For Your Safety EN-5200e Special Notes on LCD Monitors General Notes The following symptoms are normal with an LCD monitor and do not indicate a problem: • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • Do not install the monitor near heat sources such as radiators or air ducts.
Before You Operate the Monitor EN-5200e Installing & Removing the Base General Features: Package Contents • 38.1cm(15") TFT Color LCD Monitor The box that your monitor was shipped in should have included the following items: 1. EN-5200e LCD Monitor 2. Power Cord 3. Windows 95/98/2000/ME/XP INF Driver Disk 4. Quick Start Guide 5.
Before You Operate the Monitor EN-5200e Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your LCD monitor's Power Adapter. 3. Connect the Power Adapter to your monitor. 4. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip.
Before You Operate the Monitor EN-5200e Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to your own preference. • Hold the stand firmly when you change the monitor's angle. • Do not touch the LCD screen when you change the angle. It may cause damage or breakage. • Be careful to avoid pinching your hand in the swivel base. • You can adjust the monitor's angle from -5° to 25°.
Before You Operate the Monitor EN-5200e Preparing To Install An Optional Wall Mounting Arm (Not Supplied) This monitor can be attached to a wall mounting arm you can purchase separately. Disconnect power before performing this procedure. Follow these step. 1. Pull the screw covers off the back of the monitor. 2. Support the base and remove the screws. 3. Remove the base. 4. Follow the manufacturer’s instructions to assemble the wall mounting arm. See next page for further installation instructions.
Before You Operate the Monitor EN-5200e nstall An Optional Wall Mounting Arm (Not Supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Insert the 4 screws into the holes and tighten. 3. Insert the power cable into the slot on the back of the monitor. NOTE: The Envision EN-5200e is compatible with the Ergotron line of mounting and arm solutions.
Operating Instructions EN-5200e Front Panel Buttons Auto: Press this button to automatically set the H-Position, V-Position, Clock and Focus settings. Brightness: Press this button to adjust the picture’s brightness. If the OSD window is open, this button allows you to move within the window and select desired functions. Contrast: Press this button to adjust the picture’s contrast. If the OSD window is open, this button allows you to move within the window and select desired functions.
Operating Instructions EN-5200e Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the settings of the function. EN-5200e 5. To save and exit, highlight the EXIT icon and press MENU or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4.
Operating Instructions EN-5200e Plug & Play DDC1/2B Feature How to Install INF & ICM File This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B.
Technical Support (FAQ) Problem EN-5200e Possible Solution Power LED is not ON • Make sure the power button is ON. • Make sure the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play • Confirm that your computer is Plug & Play compatible. • Confirm that your video card is Plug & Play compatible. • Inspect the video cable and make sure that none of the pins are bent. • Make sure the Envision monitor drivers are installed.
Technical Support (FAQ) Problem EN-5200e Possible Solution Screen image is not centered or sized properly • Adjust the CLOCK1 and FOCUS2 settings or press the AUTO button to automatically re-configure the monitor’s settings. Picture has color defects (white does not look white) • Adjust the settings for Red, Green and/or Blue colors or select a different color temperature: C1 or C2. Poor brightness or contrast • The life time of the back-light is limited.
Technical Support (FAQ) Error Message EN-5200e Possible Solution Input not supported • Your computer has been set to an incompatible display mode. Right click on the desktop and choose Properties. Click the Settings tab then set your computer’s display mode to one of the settings listed in the resolution chart below. Unsupported mode try different video card setting • Your computer’s resolution is out of VESA specifications. Right click on the desktop and choose Properties.
Appendix Specifications LCD Panel Input Driving system TFT Color LCD Size 15.0" (38.1 cm) Pixel pitch (0.297 mm) (H) x (0.297 mm) (V) Viewable angle 120° (H) 100° (V) Response time 30 milliseconds Video Red, Green, Blue Analog Interface Separate Sync. H/V TTL H-Frequency 30 kHz - 60 kHz V-Frequency 50-75 Hz EN-5200e Plug & Play VESA DDC1/ 2BTM Input Connector D-Sub 15-pin Input Video Signal Analog: 0.7 Vpp 75 OHM, Positive Maximum Screen Size Horizontal: 12.0" (304.
Appendix Specifications (continued) Front Panel Buttons Auto Brightness Contrast Power Switch MENU/ Exit External Controls: Contrast Brightness Focus Clock H-Position V-Position Auto-Center C1 C2 RGB Color temp.
Appendix EN-5200e Factory Preset Timing Table Standard VGA SVGA XGA EN-5200e Resolution (in pixels) Horizontal Frequency Vertical Frequency 720 × 400 31.47 kHz 70 Hz 640 × 480 31.47 kHz 60 Hz 640 × 480 35.00 kHz 66.6 Hz 640 × 480 37.50 kHz 75 Hz 800 × 600 37.879 kHz 60 Hz 800 × 600 46.875 kHz 75 Hz 832 × 624 49.725 kHz 75 Hz 1024 × 768 48.363 kHz 60 Hz 1024 × 768 56.476 kHz 70 Hz 1024 × 768 60.02 kHz 75 Hz 1024 × 768 60.241 kHz 74.
Appendix EN-5200e Connector Pin Assignment Pin Number EN-5200e Description Pin Number Description 1 Red 9 +5V 2 Green 10 Detect Cable 3 Blue 11 NC 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground 19 31MY02
Limited 3-Year Warranty This is a warranty statement for Envision color monitors including those sold within North America as specified. Envision Peripherals, Inc. (EPI) warrants this product to be free from defects in material and workmanship for a period of three (3) years after the original date of consumer purchase. During this period, EPI will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below*.
Warranty (continued) Although this limited warranty gives you specific legal rights, you may have other rights which may vary from state to state. In the United States of America, this limited warranty is only valid for products purchased in the Continental United States, Alaska, and Hawaii. Outside the United States, this limited warranty is only valid for products purchased in Canada. In the United States, to obtain service under this limited warranty: 1.