- ENVISION LCD Monitor G2016wa Owner's Manual

ManualsBrandsEnvision Peripherals ManualsFlat Panel TVG2016wa

Summary of content (20 pages)

PAGE 1
PAGE 2
TABLE OF CONTENTS FOR YOUR SAFETY --------------------------------------------------1 SAFETY PRECAUTIONS --------------------------------------2 SPECIAL NOTES ON LCD MONITORS -------------------3 BEFORE YOU OPERATE THE MONITOR ---------------------3 FEATURES --------------------------------------------------------3 PACKING LIST ---------------------------------------------------3 INSTALLATION INSTRUCTIONS ---------------------------4 CONTROLS AND CONNECTORS --------------------------5 ADJUSTING THE VIEWING
PAGE 3
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
PRECAUTIONS  Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.  Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
PAGE 5
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES  Due to the nature of the fluorescent light, the screen may flicker during    initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
PAGE 6
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Figure 1 Remove Installing and Removing the Base POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the power cord into your LCD monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet.
PAGE 7
CONTROLS AND CONNECTORS CONNECTING CABLES Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the D-sub Signal input socket on back of the monitor and connect the other end to the computer’s D-Sub port. Connecting the Power Cord: Connect the power cord into your LCD monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied).
PAGE 8
ADJUSTING THE VIEWING ANGLE  For optimal viewing it is recommended to look at the full face of the   monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -5 to 20. Figure 3 NOTES  Do not touch the LCD screen when you change the angle. It may cause  damage or break the LCD screen.
PAGE 9
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.  Connect the cables according to instructions above (section Connecting Cables)  Press the power button to turn on the monitor. The power indicator will light up. Figure 4 External Control Button EXTERNAL CONTROLS 1. 2. 3. 4. 5. 6. 7.
PAGE 10
FRONT PANEL CONTROL  Power Button / Power Indicator: Press this button to turn the monitor ON or OFF. Green — Power On mode. Orange — Off mode.  MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status.  > /Volume: Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated.
PAGE 11
HOW TO ADJUST A SETTING 1. 2. 3. 4. Press the MENU-button to activate the OSD window. Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press MENU button again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU button to activate it. Press < or > to change the settings of the selected function.
PAGE 12
ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Sub Menu Menu Item Icon Sub Menu Brightness Description Backlight Adjustment Contrast Contrast from Digital-register Standard Standard Mode Text Eco Luminance Text Mode Internet Internet Mode Game Game Mode Movie Movie Mode Sports Sports Mode Gamma1 Adjust to Gamma 1 Gamma Gamma2 Adjust to Gamma 2 Gamma3 Adjust to Gamma 3 DCR Image Setup Off Disable dynamic contrast ratio On Enable dynamic contrast ratio
PAGE 13
User-M Magenta register Main Menu Item Main Sub Menu Menu Item Icon on or off Disable or Enable Full Enhance Mode Nature Skin on or off Disable or Enable Nature Skin Mode Green Field on or off Disable or Enable Green Field Mode on or off Disable or Enable Sky-blue Mode AutoDetect on or off Demo Frame Size Adjust Frame Size Brightness Adjust Frame Brightness Adjust Frame Contrast Hue Adjust Frame Hue Saturation Adjust Frame Saturation Position Adjust Frame Position Bright Frame on or off
PAGE 14
PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.
PAGE 15
TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play Picture is fuzzy Picture bounces or a wave pattern is present in the picture The power LED is ON but there’s no video or no picture. Missing one of the primary colors (RED, GREEN, or BLUE) Screen image is not centered or sized properly.
PAGE 16
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. MODE NOT SUPPORTED : Your computer has been set to unsuitable display mode ,set the computer to display mode given in the following table (See page 17).
PAGE 17
APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Input Size 20" Widescreen Pixel pitch 0.258mm(H) × 0.258mm(V) Video R,G,B Analog Interface Separate Sync. H/V TTL H-Frequency 30kHz – 83kHz V-Frequency 55-75Hz Display Colors 16.7M Colors Dot Clock 146.25MHz Max. Resolution 1680 x 1050@60Hz Plug & Play ON Mode VESA DDC2BTM ≤49W OFF Mode ≤1W EPA ENERGY STAR® Input Connector 15-pin D-Sub Input Video Signal Analog:0.
PAGE 18
            Switch External Controls: Functions Power Consumption Audio Output ( Maximum ) Auto Adjust Key < / Volume > / Volume Power Button MENU Luminance Image Setup Color Temp. Color Boost Picture Boost OSD Setup Extra 49 Watts Rated Power 1.
PAGE 19
Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-Mode 640 × 350 31.47kHz 70Hz Dos-Mode 720 × 400 31.47kHz 70Hz 640 × 480 31.47kHz 60Hz 640 × 480 35.00kHz 66.6Hz 640 × 480 37.50kHz 75Hz 640 × 480 37.86kHz 72Hz 800 × 600 37.879kHz 60Hz 800 × 600 46.875kHz 75Hz 800 × 600 35.16kHz 56Hz 800 × 600 48.01kHz 72Hz 832 × 624 49.725kHz 75Hz 1024 × 768 48.363kHz 60Hz 1024 × 768 56.476kHz 70Hz 1024 × 768 60.02kHz 75Hz 1280 × 1024 64.
PAGE 20
CONNECTOR PIN ASSIGNMENT 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. 1. 2. 3. 4. 5. 6. 7. 8. DESCRIPTION PIN NO. DESCRIPTION 9. 10. 11. 12. 13. 14. 15. +5V Detect Cable Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock Red Green Blue Ground Ground R-Ground G-Ground B-Ground DVI-D 24pin Color Display Signal Cable Pin 1. 2. 3. 4. 5. 6. 7. 8. Meaning TMDS Data2TMDS Data2+ TMDS Data 2/4 Shield not connected not connected DDC Clock DDC Data Analogue Vertical Sync Pin 9. 10. 11.