G218a1
Operation Instructions FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING: (FOR FCC CERTIFIED MODELS) This monitor has been tested and found compliant with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper protection against harmful interference to a residential installation. This monitor generates, uses, and can radiate radio frequency energy.
Content English Safety Precautions.............................................................................1 First Setup .........................................................................................2 Quick Installation.............................................................................2-5 Rear View of the Product .................................................................. 6 Front View of the Product ..................................................................
This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However, improper use or installation may result danger to the monitor as well as to the user. Carefully go over the following WARNINGS before installation and keep this guide handy. WARNINGS: This monitor should be operated only at the correct power sources indicated on the label on the rear end of the monitor. If you’re unsure of the power supply in your residence, consult your local dealer or power company.
First Setup English Congratulation for purchasing this monitor of high performance! This monitor comes with the following accessories: Power Cable D-Sub Cable (15 pin) DVI Cable (24 pin) Audio Cable User’s Guide Quick Start Guide Warranty Documents Quick Installation Installing & Removing the Base Install Remove 2
Preparing To Install The Optional Wall Mount Arm (Not Included) English This monitor can be attached to a wall mounting arm you can purchase separately. Turn the power OFF then dis-connect the cables from the monitor before performing the procedure below. Lay the monitor face down on a soft surface. 1. Remove the base. It is attached to the stand by hooks. 2. Remove the 4 screws holding the stand to the hinge. 3. Remove the stand.
Attaching The Optional Wall Mount Arm (not supplied) English Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Insert the 4 screws into the holes and tighten. 3. Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instrucstions on attaching it to the wall.
Connecting the Monitor Make sure both monitor and computer are powered OFF. Connect the video cable ( D-Sub cable) to the computer, then to the monitor. 3. Connect DVI cable (Optional) Connect the DVI cable from DVI output of computer to the DVI input of the monitor. 4. Connect audio cable Connect one end of the audio cable to the back of the monitor and connect the other end to the computer’s audio out port. 5. Power-ON computer and monitor Power-ON the computer, then Power-ON the monitor. 6.
Rear View of the Product English ➐ ➑ ➐ POWER INPUT ➑ AUDIO INPUT ➒ ➓ ➒ DVI INPUT (DVI 24 PIN) ➓ VGA INPUT (D-SUB 15 PIN) Front View of the Product ➊➋➌➍ ➎➏ ➊ OSD TURN ON/OFF ➋ SCROLL DOWN/DECREASE ➌ SCROLL UP/INCREASE ➍ CONFIRM SELECTION ➎ POWER ON/OFF ➏ LED INDICATOR 6
Using On Screen Display (OSD) Functions English 1 Display main menu. Exit from OSD menu. 2 Auto adjust the image when not in main menu. Confirm the selection. V or W Select the desired item when in OSD menu. When not in OSD menu, it is to immediately activate Contrast/ Brightness. It should be changed to Contrast/ Brightness by pressing button V or W . ▼+▲ Recall both of Contrast and Brightness.
OSD Functions English Auto Image Adjust : Auto adjust Horizontal Position, Vertical Position, Phase (Fine Tune) and Clock (H. Size) of the screen. Available in Analog mode only. Contrast : Adjust the foreground white level of screen image. V : increase contrast, W: decrease contrast. Brightness : Adjust the luminance of the video. V : increase brightness, W : decrease brightness. Input Select : Select Analog (D-sub) or Digital (DVI) Input Audio Adjust : Adjust the audio functions.
Sharpness : Adjust the clarity of a non-WSXGA (1680x1050) signal with ▼ or ▲ button. Setup Menu : Set up Language Select, Resolution Notice, OSD Position, OSD Time Out, and OSD Background. Setup Menu>Language Select : Allow users to choose from available languages. Setup Menu>Resolution Notice: Resolution Notice is to remind the user to set the resolution to 1680x1050 for best image quality when the resolution setting is not at 1680 x 1050.
Supported Timing Modes English VGA 720 x 400 @ 70Hz VGA 640 x 480 @ 60Hz MAC 640 x 480 @ 67Hz VESA 640 x 480 @ 75Hz VESA 800 x 600 @ 56Hz VESA 800 x 600 @ 60Hz VESA 800 x 600 @ 72Hz VESA 800 x 600 @ 75Hz MAC 832 x 624 @ 75Hz VESA 848 x 480 @ 60Hz VESA 1024 x 768 @ 60Hz VESA 1024 x 768 @ 70Hz VESA 1024 x 768 @ 75Hz VESA 1152 x 864 @ 75Hz VESA 1280 x 720 @ 60Hz VESA 1280 x 960 @ 60Hz VESA 1280 x 768 @ 60Hz VESA 1280 x 768 @ 75Hz VESA 1280 x 1024 @ 60Hz VESA 1280 x 1024
Technical Information LCD Panel 22” Widescreen TFT Power Management EPA ENERGY STAR® Off Mode: <1W Displayable Resolution WSXGA 1680 x 1050 max. Vertical Frequency 60Hz max. Input Signal Analog (D-sub) & Digital (DVI) with HDCP Pixel Dimension 0.282 x 0.282 mm LCD Display Color 16.7M Tilt 0°~20° Active Display Area 473.76 mm x 296.
Care and Maintenance English Care Avoid exposing your monitor directly to sunlight or other heat source. Place your monitor away from the sun to reduce glare. Put your monitor in a well ventilated area. Do not place any heavy objects on top of your monitor. Make certain your monitor is installed in a clean and moisture-free area. Keep your monitor away from magnets, motors, transformers, speakers, and TV sets.
Instructions d’Utilisation Merci d’avoir acheté ce moniteur couleur multi-scan à haute résolution. Veuillez lire attentivement ce guide avant l’installation. Ce moniteur a été testé et à été trouvé conforme aux limites pour un appareil numérique de Classe B, suivant la partie 15 des règlements de la FCC. Ces limites ont été développées pour offrir une protection satisfaisante contre les interférences nuisibles dans une installation résidentielle.
Contenu Français Précautions de Sécurité.....................................................................1 Première Installation ..........................................................................2 Installation Rapide ..........................................................................2-5 Produit vu de dos ...............................................................................6 Vue avant du produit..........................................................................
Précautions de Sécurité Ce moniteur à été fabriqué et testé à partir du principe que la sécurité de l’utilisateur est primordiale. Néanmoins, l’utilisation ou l’installation incorrecte peut causer un danger à l’appareil aussi bien que à l’utilisateur. Lisez attentivement les AVERTISSEMENTS suivants avant de commencer l’installation et gardez ce guide à portée de main.
Première Installation Français Félicitations avec votre achat de ce moniteur de haute performance! Ce moniteur est fourni avec les accessoires suivants : Cordon d’Alimentation. Câble D-Sub (15 broches) Câble DVI (24 broches) Câble Audio. Guide de l’utilisateur.
Préparer l’installation du support mural, en option (non inclus) Français Cet écran peut être fixé sur un support mural, à acheter séparément. Mettre l’écran hors tension puis débrancher les câbles de l’écran, avant de suivre la procédure ci-dessous. Déposer l’écran, avec la face posée contre une surface douce. 1. Enlevez la base. Il est fixé aux crochets de tenir prêt. 2. Enlevez les 4 vis tenant le stand sur la charnière. 3. Enlevez la stand.
Fixer le support mural, en option (non inclus) Français Suivre les étapes pour installer le support mural : 1. Placer le support mural à l’arrière de l’écran. Aligner les trous sur le support et les trous à l'arrière de l'écran. 2. Insérer les 4 vis dans les trous et les serrer. 3. Rebrancher les câbles. Se référer au mode d'emploi joint au support mural (en option) pour les instructions concernant la fixation du support sur le mur.
Connecter le moniteur 1. Connectez le cordon d'alimentation 5 Français Connectez le cordon d'alimentation au dos du moniteur. Branchez le cordon d’alimentation dans une prise de courant proche. 2. Connecter le câble Analogique vidéo (Câble D-Sub) Assurez-vous qu'à la fois le moniteur et l'ordinateur sont bien SOUS tension. Connectez le câble vidéo (câble D-Sub) de la sortie D-Sub sur l'ordinateur sur l'entrée D-Sub sur le moniteur. 3.
Produit vu de dos Français ➐ ➑ ➐ ENTREE DU CA ➑ ENTREE AUDIO ➒ ➓ ➒ ENTREE DVI (DVI 24 BROCHES) ➓ ENTREE VGA (D-SUB 15 BROCHES) Vue avant du produit ➊➋ ➌ ➍ ➎ ➏ ➊ ACTIVER/QUITTER OSD ➋ DEFILER VERS LE BAS/ DIMINUER ➌ DEFILER VERS LE HAUT/ ➍ CONFIRMER LA SÉLECTION ➎ SOUS TENSION/ HORS TENSION ➏ INDICATEUR DEL AUGMENTER 6
Utiliser les fonctions d'affichage d'écran (OSD) 1 Afficher le menu principal. Quitter le menu OSD. 2 Ajuster automatiquement l'image en dehors du menu principal. V ou W Sélectionnez l'élément désiré quand vous êtes dans le menu OSD. Quand vous n'êtes pas dans le menu OSD, cela permet d'activer immédiatement le Contraste/Luminosité. Peut être changé en Contraste/Luminosité en appuyant sur le bouton V ou W .
Fonctions OSD Réglage automatique (Auto Image Adjust) : Ajuste automatiquement la position horizontale, la position verticale, la phase(accord fin) et l'horloge (taille H). Disponible en mode Analogique uniquement. Français Contraste (Contrast) : Pour ajuster le niveau blanc du premier plan de l'image de l'écran. V : augmenter le contraste, W: diminuer le contraste. Luminosité (Brightness) : Pour régler la luminance de la vidéo. V : augmenter la luminosité, W : diminuer la luminosité.
Taille Horiontale (Horizontal Size) : Ajuste la largeur de l'image de l'écran. W : diminue la largeur de l'image de l'écran, V : augmente la largeur de l'image de l'écran. Réglage image (Fine Tune) : Pour ajuster le temps de retard. Appuyez sur W ou V pour ajuster à la préférence de l'utilisateur. Finesse (Sharpness) : Pour ajuster la clarté d'un signal non-WSXGA (1680x1050) avec le bouton W ou V.
Interruption OSD (OSD Time Out) : Pour désactiver automatiquement l'affichage d'écran (OSD) après une durée prédéfinie. Arrière plan OSD (OSD Background) : Vous permet d’activer ou de désactiver l’arrière plan à l’écran. Français Rappel de mémoire (Memory Recall) : Pour rétablir les paramètres d'usine pour les contrôles vidéo & audio. Appuyez sur le bouton 2 pour sélectionner l’option de menu de Rappel Mémoire.
Supported des modes minutage 720 x 400 @ 70Hz VGA 640 x 480 @ 60Hz MAC 640 x 480 @ 67Hz VESA 640 x 480 @ 75Hz VESA 800 x 600 @ 56Hz VESA 800 x 600 @ 60Hz VESA 800 x 600 @ 72Hz VESA 800 x 600 @ 75Hz MAC 832 x 624 @ 75Hz VESA 848 x 480 @ 60Hz VESA 1024 x 768 @ 60Hz VESA 1024 x 768 @ 70Hz VESA 1024 x 768 @ 75Hz VESA 1152 x 864 @ 75Hz VESA 1280 x 720 @ 60Hz VESA 1280 x 960 @ 60Hz VESA 1280 x 768 @ 60Hz VESA 1280 x 768 @ 75Hz VESA 1280 x 1024 @ 60Hz VESA 1280 x 1024 @ 75Hz
Informations Technique Spécifications Techniques Français Panneau LCD 22” Grand écran TFT Gestion de Courant Mode Désactivé EPA ENERGY STAR® : <1W Résolution Affichable WSXGA 1680 x 1050 max. Fréquence Verticale maximale de 60Hz. Signal d'entrée Analogique (D-sub) et numérique (DVI) avec HDCP Dimension des Pixels 0.282 x 0.282 mm Couleur de l’affichage LCD 16.7M Inclination 0°~20° Région d’affichage Actif 473.76 mm x 296.
Soins et Maintien Remarque Sortez le LCD de l’emballage et enlevez le sac en plastique et la Mousse en Polystyrène. Tirez la base de la position parallèle par rapport au panneau pour la mettre à la verticale. Réglez l'inclinaison du panneau entre 0 degré en avant et 20 degrés en arrière. Vous devez pousser plus fort pour dépasser 20 degrés en arrière mais cette position est réservée à l'emballage de l'unité pour permettre un encombrement plus faible pour le stockage seulement.
Allumé mais pas d ‘affichage à l’écran Vérifiez que le câble vidéo, fourni avec le moniteur soit bien solidement fixé au port de sortie du signal vidéo, situé à l’arrière de l’ordinateur. Sinon, fixé le convenablement. Ajustez la clarté. Français Couleurs incorrectes ou anormales Si une des couleurs manque (rouge, vert, bleu), contrôlez le câble vidéo pour vous assurez qu’il soit bien correctement connecté. Des broches desserrées ou cassées peuvent créer une connexion incorrecte.
Instrucciones de operación Gracias por comprar este monitor, un monitor color multi-scan de alta resolución. Por favor lea esta guía minuciosamente antes de hacer la instalación. ACUERDO DE INTERFERENCIA DE RADIO FRECUENCIA PARA FCC ADVERTENCIA: (PARA MODELOS CERTIFICADOS COMO FCC) Reorientar o reposicionar la antena receptora. Mover el monitor y el receptor lejos el uno del otro. Conectar el monitor a una toma de corriente en un circuito diferente de aquel al que está conectado el receptor.
Contenido Precauciones de Seguridad ............................................................... 1 Primera Configuración ....................................................................... 2 Rápida Instalación .......................................................................... 2-5 Vista Trasera del Producto ................................................................ 6 Vista Frontal del Producto..................................................................
Precauciones de Seguridad Este monitor ha sido manufacturado y probado bajo el principio de que la seguridad del usuario es lo primero. Sin embargo, el uso o la instalación impropia puede resultar de peligro para el monitor tanto como para el usuario. Lea cuidadosamente las siguientes ADVERTENCIAS antes de la instalación y conserve a mano esta guía. ADVERTENCIAS: No trate de reparar el monitor por usted mismo cuando esto concierne a partes no ajustables por el usuario.
Primera Configuración Gracias por comprar este monitor de alto rendimiento! Este monitor viene con los siguientes accesorios: Cable toma de corriente. Cable VGA (15 pin D-Sub) Cable DVI (24 pin DVI) Cable Audio. Guía de usuario.
Preparación para instalar el brazo de montaje de pared opcional (no incluido) Español Este monitor puede ser colocado en un brazo de montaje de pared adquirido por separado. Apague y luego desconecte los cables del monitor antes de realizar el procedimiento que aparece más adelante. Coloque el monitor hacia abajo sobre una superficie suave. 1. Retire la base. Se une a los ganchos del hacer una pausa. 2. Retire los 4 tornillos que llevan a cabo el soporte a la bisagra. 3. Retire la soporte.
Colocación del brazo de montaje de pared opcional (no incluido) Español Siga los pasos que aparecen a continuación para finalizar la instalación del brazo de montaje de pared: 1. Coloque el brazo de montaje de pared en la parte trasera del monitor. Haga coincidir los orificios del brazo con los orificios de la parte trasera del monitor. 2. Coloque los 4 tornillos en los orificios y apriételos. 3. Vuelva a conectar los cables.
1. Conecte el cable de toma de corriente Enchufe el cable que toma la corriente a un toma corriente y después al monitor 2. Conectar el cable de vídeo (cable D-Sub) Asegúrese de que tanto el monitor como el equipo están APAGADOS. Conecte el cable de vídeo (cable D-Sub) entre la salida D-Sub del equipo y la entrada D-Sub del monitor. 3. Conecte el cable DVI (Opcional) Conecte el cable DVI entre la salida DVI del equipo y la entrada DVI del monitor. 4.
Vista Trasera del Producto Español ➐ ➑ ➐ ENTRADA AC ➑ ENTRADA DE SONIDO ➒ ➓ ➒ ENTRADA DVI (24 PIN DVI) ➓ ENTRADA VGA (15 PIN D-SUB) Vista Frontal del Producto ➊➋➌➍ ➎➏ ➊ ACTIVAR/SALIR OSD ➍ CONFIRMAR SELECCIÓN ➋ DESPLAZAR ABAJO/DISMINUIR ➎ ENCENDER/APAGAR ➌ DESPLAZAR ARRIBA/AUMENTAR ➏ INDICADOR LED 6
Usar las Funciones de la Muestra En Pantalla (OSD) 1 Muestra el menú principal. Sale del menú OSD. 2 Autoajusta la imagen cuando no está en el menú principal. Confirma la selección. VoW Selecciona el ítem deseado cuando se encuentra en el menú OSD.
Funciones de OSD Ajuste automático (Auto Image Adjust) : Ajuste automático de posición horizontal, posición vertical, fase (ajuste fino) y reloj (Tamaño-H). Disponible solamente en el modo Analógico. Contraste (Contrast) : Ra ajustar el nivel de blanco de la imagen en pantalla. V : aumentar contraste, W: disminuir contraste. Brillo (Brightness) : Para ajustar la luminancia del vídeo. V : aumenta el brillo, W : reduce el brillo.
anchura de la imagen en panalla. Posición H./V. (H./V. Position) : Para ajustar la posición horizontal y vertical del video. Posición H : V : mueve la pantalla a la derecha, W : mueve la pantalla a la izquierda. Posición V : V : mueve la pantalla hacia arriba, W : mueve la pantalla hacia abajo. Sintonizar (Fine Tune) : Para ajustar el retardo temporal. Pulse W o V para ajustar a la preferencia del usuario.
Visualización de OSD (OSD Background) : Activar o desactivar el fondo de la presentación en pantalla. Restituir Memoria (Memory Recall) : Para llamar las configuraciones de fábrica de vuelta para los controles de Vídeo & Audio. Oprima el botón 2 para seleccionar la opción de menú Memoria.
Información Técnica Especificaciones Técnicas 22” Pantalla Ancha TFT Administración de energía Modo Apagado de EPA ENERGY STAR®: <1W Resolución Visualizable WSXGA máximo 1680 x 1050. Frecuencia Vertical máxima 60Hz. Señal de Entrada Analógica (D-sub) & Digital (DVI) con HDCP Dimensión de Píxel 0.282 x 0.282 mm Visualización del Color LCD 16.7M Inclinación 0°~20° Area de Visualización Activa 473.76 mm x 296.
Mantenimiento y Cuidado Cuidado Evite exponer el monitor directamente a la luz del sol o otra fuente de calor. Coloque su monitor lejos del sol para reducir el deslumbramiento. No coloque objetos pesados encima de su monitor. Asegúrese de que el monitor esté instalado en un área limpia y libre de humedad. Mantenga el monitor lejos de imánes, objetos magnéticos, motores, transformadores, parlantes y televisores.
Si algún color (rojo, verde, azul) están faltando, revise el cable de video para asegurarse que este está bien conectado. Pins sueltos o quebrados en el cable conector podrían causar una conexión impropia o deficiente. Conecte el monitor a otra computadora.