Product specifications

ManualsBrandsEnvision ManualsLED displaysH2062

Table of Contents

About This Guide .............................................................................................................................................. 1

National Conventions ...................................................................................................................................... 1

FCC Notice ......................................................................................................................................................... 2

WEEE Declaration .............................................................................................................................................. 2

HG Declaration .................................................................................................................................................. 3

Precautions ........................................................................................................................................................ 3

Setup stand and base ...................................................................................................................................... 4

Adjusting Viewing Angle ................................................................................................................................ 4

Connecting Cables ........................................................................................................................................... 5

Wall Mounting.................................................................................................................................................... 6

Setting Optimal Resolution ............................................................................................................................ 7

External Controls .............................................................................................................................................. 8

Menu Illustration ............................................................................................................................................... 9

Hotkey Illustration ............................................................................................................................................ 9

Menu Icon Definition ...................................................................................................................................... 10

LED Indicators ................................................................................................................................................. 14

I-Menu software .............................................................................................................................................. 14

Drives................................................................................................................................................................. 15

Technical Support .......................................................................................................................................... 17

Frequently Asked Questions ....................................................................................................................... 17

Product Specifications .................................................................................................................................. 18

EPA ENERGY STAR ® ................................................................................................................................... 19

Preset Display Modes .................................................................................................................................... 19

Pin Assignments ............................................................................................................................................ 20

Plug and Play ................................................................................................................................................... 21

Downloaded from ManualMonitor.com Manuals

Summary of content (22 pages)

PAGE 1
Table of Contents About This Guide..............................................................................................................................................1 National Conventions ......................................................................................................................................1 FCC Notice .........................................................................................................................................................
PAGE 2
About This Guide This guide describes the monitor's features, setup, and operation. information in this document is subject to change without notice. The sections are as follows:  Safety Instructions: lists safety information.  Setup: describes the initial setup process.  Using the Monitor: gives an overview of how to use the monitor.  Drivers: provides driver installation instructions for Windows.  Technical Support: provides tips and solutions for common problems.
PAGE 3
FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
HG Declaration SAFETY: Lamp Disposal LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. Precautions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.
PAGE 5
Setup stand and base Please setup or remove the base following below steps. Adjusting Viewing Angle  For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to your own preference.  Hold the stand so you do not topple the monitor when you tilt the monitor's angle.  You are able to adjust the monitor's angle from 5°to 15 °. NOTE: Do not press the LCD screen to change the viewing angle. It may cause damage or break the LCD screen.
PAGE 6
Connecting Cables Cable Connections On Back of Monitor and Computer 1. Power 2. Analog Turn off your computer before performing the procedure below. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3. Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting.
PAGE 7
Wall Mounting Preparing to Install an Optional Wall Mounting Arm This monitor can be attached to a wall mounting arm which can be purchased separately. Disconnect power before this procedure. Follow these steps: 1. Remove the stand & base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4. Insert the 4 screws into the holes and tighten. 5.
PAGE 8
Setting Optimal Resolution The recommended resolution for this monitor is 1600 by 900. To setup the monitor to this resolution, follow the steps below. 1. Click START. 2. Click SETTINGS. 3. Click CONTROL PANEL. 4. Double click DISPLAY. 5. Click SETTINGS. 6. Set the resolution SLIDE-BAR to 1600 by 900 Downloaded from ManualMonitor.
PAGE 9
External Controls Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure Below). By changing these settings, the picture quality can be adjusted to your personal preferences. 1 .Auto / Exit 2 .Eco mode (DCR) / < 3 .4:3 or wide / > 4 .Menu / Enter 5 .Power Downloaded from ManualMonitor.
PAGE 10
Menu Illustration   Press the MENU-button to activate the OSD window. Press< or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.  Press< or > to change the settings of the selected function. To exit and save, select the exit function.
PAGE 11
Menu Icon Definition Luminance Adjust Range Description Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register. Standard Mode Standard Text Mode Text Internet Mode Internet Eco mode Game Mode Game Movie Mode Movie Sports Mode Sports Gamma Gamma1 Adjust to Gamma1 Gamma2 Adjust to Gamma 2 Gamma3 Adjust to Gamma 3 DCR Enable dynamic contrast ratio On Image Setup Clock Adjust picture Clock to reduce 0-100 Downloaded from ManualMonitor.
PAGE 12
Phase 0-100 H.Position 0-100 V.Position 0-100 Adjust Picture Phase to reduce Horizontal-Line noise Adjust the horizontal position of the picture. Adjust the vertical position of the picture. Color Temp. Warm 6500K Normal 7300K Cool 9300K Recall Warm Color Temperature from EEPROM. Recall Normal Color Temperature from EEPROM. Recall Cool Color Temperature from EEPROM. Recall SRGB Color sRGB User Temperature from EEPROM. Red Red Gain from Digital-register Green Green Gain Digital-register.
PAGE 13
Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast Adjust Frame horizontal H. position Position Position Bright Frame V.position Adjust Frame vertical Position on or off Disable or Enable Bright Frame OSD Setup H.Position 0-100 V.
PAGE 14
Off Timer Select timing to turn off the 0~24hrs monitor. Show the information of the main image and sub-image Information source Reset Reset yes or no Reset the menu to default Exit Exit Exit the main OSD Notes: 1)If the product has only one signal input, the item of "Input Select" is disabled. 2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disabled.
PAGE 15
LED Indicators Status LED Color Full Power Mode Green or Blue Active-off Mode Orange or red I-Menu software Welcome to use “i-Menu” software by ENVISION. i-Menu makes it easy to adjust your display settings by mouse. Downloaded from ManualMonitor.
PAGE 16
Drives Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...’ 5. Select 'Monitor' - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below. 6.
PAGE 17
Windows XP 1. Start Windows® XP 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Select and click on the category 'Printers and Other Hardware' 4. Click on the 'Display' Item. 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button. Please follow the steps below. 7.
PAGE 18
Technical Support Frequently Asked Questions Problem & Question Possible Solutions  Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor.  In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer & video card. Check with your computer manufacturer. Also check the monitor's video cable and make sure none of No Plug & Play the pins are bent.
PAGE 19
Product Specifications Model name H2062 Driving system TFT Color LCD Viewable Image Size 508.5mm diagonal Pixel pitch 0.2768mm(H) x0.2768mm(V) Video R, G, B Analog interface Separate Sync. H/V TTL Display Color 16.7M Colors Dot Clock 108Mhz Horizontal scan range 30 kHz - 80 kHz Horizontal scan Size(Maximum) 442.8 mm Vertical scan range 55 Hz - 75 Hz Vertical scan Size(Maximum) 249.
PAGE 20
EPA ENERGY STAR ® ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, ENVISION International (Europe) GmbH has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Display Modes STAND HORIZONTAL VERTICAL FREQUENCY(kHZ) FREQUENCY(Hz) RESOLUTION VGA 640×480 @60Hz 31.469 59.94 VGA 640×480 @67Hz 35 66.667 VGA 640×480 @72Hz 37.861 72.809 VGA 640×480 @75Hz 37.5 75 Dos-mode 720×400 @70Hz 31.469 70.087 SVGA 800×600 @56Hz 35.
PAGE 21
Pin Assignments Pin Number 15-Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Ground 11 N.C. 12 DDC-Serial data 13 H-sync 14 V-sync 15 DDC-Serial clock Downloaded from ManualMonitor.
PAGE 22
Plug and Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. 2 The DDC2B is a bi-directional data channel based on the I C protocol. The host can request EDID information over the DDC2B channel. Downloaded from ManualMonitor.