Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: B32651 ... B32656 Date: May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited.
Metallized polypropylene film capacitors (MKP) B32651 ... B32656 High pulse (wound) Typical applications Electronic ballasts Switch-mode power supplies Dimensional drawing Climatic Max.
B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 10 mm Type B32651 Page 8 VR (V DC) 1250 VRMS (V AC) 450 CR (nF) 2.2 3.3 4.7 6.8 Please read Cautions and warnings and Important notes at the end of this document.
B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 15 mm Type B32652 Page 9 VR (V DC) 250 400 630 1000 1250 1600 1600 2000 VRMS (V AC) 160 200 250 250 500 500 700 700 CR (nF) 1.0 1.5 2.2 3.3 4.7 5.6 6.8 10 12 15 22 33 47 56 68 100 120 150 220 330 390 470 560 680 820 1000 Please read Cautions and warnings and Important notes at the end of this document.
B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 22.5 mm Type B32653 Page 12 VR (V DC) 250 400 630 1000 1250 1600 2000 2000 VRMS (V AC) 160 200 250 250 500 500 700 1000 CR (nF) 2.2 3.3 4.7 6.8 10 12 15 22 33 47 56 68 82 100 120 150 220 330 470 560 680 1000 1200 1500 2200 3300 Please read Cautions and warnings and Important notes at the end of this document.
B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 27.5 mm Type B32654 Page 15 VR (V DC) 250 400 630 1000 1250 1600 2000 VRMS (V AC) 160 200 250 250 500 500 700 CR (nF) 22 33 47 68 82 100 150 220 330 470 560 680 820 1000 1200 1500 2200 2700 3300 4700 5600 6800 8200 Please read Cautions and warnings and Important notes at the end of this document.
B32651 ... B32656 High pulse (wound) Overview of available types Lead spacing 37.5 mm Type B32656 Page 17 VR (V DC) 850 1000 1250 1600 2000 VRMS (V AC) 450 500 500 600 700 CR (nF) 100 150 220 330 470 560 680 820 1000 1200 1500 2200 Please read Cautions and warnings and Important notes at the end of this document.
B32651 High pulse (wound) Ordering codes and packing units (lead spacing 10 mm) VR V DC1) 1250 VRMS CR f ≤1 kHz V AC nF 450 2.2 3.3 4.7 6.8 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 Ordering code (composition see below) B32651A7222+*** B32651A7332+*** B32651A7472+*** B32651A7682+*** Ammo pack pcs./MOQ 4000 3320 3320 2720 Reel Untaped pcs./MOQ 6800 5200 5200 4400 pcs.
B32652 High pulse (wound) Ordering codes and packing units (lead spacing 15 mm) VR V DC 250 400 630 VRMS CR f ≤1 kHz V AC nF 160 150 220 330 470 680 820 1000 200 68 100 150 220 330 470 560 680 250 33 47 68 100 150 220 330 390 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.
B32652 High pulse (wound) Ordering codes and packing units (lead spacing 15 mm) VR V DC 1000 1250 1600 1600 VRMS CR f ≤1 kHz V AC nF 250 10 15 22 33 47 68 100 120 150 500 6.8 10 15 22 33 47 56 500 3.3 4.7 6.8 10 15 22 700 2.2 3.3 4.7 6.8 10 12 15 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.
B32652 High pulse (wound) Ordering codes and packing units (lead spacing 15 mm) VR V DC 2000 VRMS CR f ≤1 kHz V AC nF 700 1.0 1.5 2.2 3.3 4.7 5.6 6.8 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32652A2102+*** B32652A2152+*** B32652A2222+*** B32652A2332+*** B32652A2472+*** B32652A2562+*** B32652A2682+*** Ammo pack pcs.
B32653 High pulse (wound) Ordering codes and packing units (lead spacing 22.5 mm) VR V DC 250 400 630 VRMS CR f ≤1 kHz V AC nF 160 220 330 470 680 1000 1200 1500 2200 3300 200 150 220 330 470 680 1000 1200 1500 2200 250 100 150 220 330 470 560 680 1000 1200 Max. dimensions w×h×l mm 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 10.5 × 18.5 × 26.5 11.0 × 20.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.
B32653 High pulse (wound) Ordering codes and packing units (lead spacing 22.5 mm) VR V DC 1000 1250 1600 VRMS CR f ≤1 kHz V AC nF 250 33 47 68 100 150 220 330 470 560 500 22 33 47 68 100 120 150 220 500 6.8 10 15 22 33 47 56 68 82 100 Max. dimensions w×h×l mm 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.
B32653 High pulse (wound) Ordering codes and packing units (lead spacing 22.5 mm) VR V DC 2000 2000 VRMS CR f ≤1 kHz V AC nF 700 3.3 4.7 6.8 10 15 22 33 1000 2.2 3.3 4.7 6.8 10 12 15 22 Max. dimensions w×h×l mm 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 11.0 × 20.5 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 10.5 × 20.5 × 26.5 12.0 × 22.0 × 26.5 14.5 × 29.5 × 26.5 14.5 × 29.5 × 26.
B32654 High pulse (wound) Ordering codes and packing units (lead spacing 27.5 mm) VR V DC 250 400 630 1000 VRMS CR f ≤1 kHz V AC nF 160 1500 2200 3300 4700 5600 6800 8200 200 1000 1500 2200 3300 4700 5600 250 680 1000 1500 2200 2700 3300 250 220 330 470 680 820 1000 1200 1500 Max. dimensions w×h×l mm 11.0 × 21.0 × 31.5 12.5 × 21.5 × 31.5 15.0 × 24.5 × 31.5 18.0 × 27.5 × 31.5 19.0 × 30.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 11.0 × 21.0 × 31.5 12.5 × 21.5 × 31.5 14.0 × 24.5 × 31.5 19.0 × 30.
B32654 High pulse (wound) Ordering codes and packing units (lead spacing 27.5 mm) VR V DC 1250 1600 2000 VRMS CR f ≤1 kHz V AC nF 500 100 150 220 330 470 560 680 500 47 68 100 150 220 700 22 33 47 68 82 100 Max. dimensions w×h×l mm 11.0 × 21.0 × 31.5 11.0 × 21.0 × 31.5 14.0 × 24.5 × 31.5 18.0 × 27.5 × 31.5 21.0 × 31.0 × 31.5 22.0 × 36.5 × 31.5 22.0 × 36.5 × 31.5 11.0 × 21.0 × 31.5 11.0 × 21.0 × 31.5 14.0 × 24.5 × 31.5 18.0 × 27.5 × 31.5 21.0 × 31.0 × 31.5 11.0 × 21.0 × 31.5 13.5 × 23.0 × 31.5 18.
B32656 High pulse (wound) Ordering codes and packing units (lead spacing 37.5 mm) VR V DC 850 1000 1250 1600 2000 VRMS CR f ≤1 kHz V AC nF 450 220 330 470 680 1000 500 470 680 1000 1200 1500 2200 500 220 330 470 680 820 1000 1200 600 100 150 220 330 470 560 680 820 700 100 150 220 330 470 Max. dimensions w×h×l mm 12.0 × 22.0 × 42.0 12.0 × 22.0 × 42.0 12.0 × 22.0 × 42.0 16.0 × 28.5 × 42.0 18.0 × 32.5 × 42.0 14.0 × 25.0 × 42.0 16.0 × 28.5 × 42.0 20.0 × 39.5 × 42.0 28.0 × 37.0 × 42.0 28.0 × 37.0 × 42.
B32651 ... B32656 High pulse (wound) Technical data Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR Dissipation factor tan δ (in 10-3) at at 20 °C (upper limit values) ≤27 nF 27 nF 0.33 µF Insulation resistance Rins or time constant τ = CR Rins 100 GΩ 30000 s at 20 °C, rel.
B32651 ... B32656 High pulse (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor.
B32651 ... B32656 High pulse (wound) k0 values Lead spacing VR VRMS V DC V AC 250 160 400 200 630 250 850 450 1000 250 500 1250 450 500 1600 500 600 700 2000 700 1000 10 mm k0 in V2/µs 25 000 000 15 mm 22.
B32651 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 10 mm 1250 V DC/450 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32652 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 15 mm 250 V DC/160 V AC 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32652 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 15 mm 1250 V DC/500 V AC 1600 V DC/500 V AC 1600 V DC/700 V AC 2000 V DC/700 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32653 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 22.5 mm 250 V DC/160 V AC 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32653 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 22.5 mm 1250 V DC/500 V AC 1600 V DC/500 V AC 2000 V DC/700 V AC 2000 V DC/1000 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32654 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 27.5 mm 250 V DC/160 V AC 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32654 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 27.5 mm 1250 V DC/500 V AC 1600 V DC/500 V AC 2000 V DC/700 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32656 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 37.5 mm 850 V DC/450 V AC 1000 V DC/500 V AC 1250 V DC/500 V AC 1600 V DC/600 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32656 High pulse (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C) For TA >90 °C, please refer to "General technical information", section 3.2.3. Lead spacing 37.5 mm 2000 V DC/700 V AC Please read Cautions and warnings and Important notes at the end of this document.
B32651 ... B32656 High pulse (wound) Mounting guidelines 1 Soldering 1.1 Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C).
B32651 ... B32656 High pulse (wound) Immersion depth 2.0 +0/ 0.5 mm from capacitor body or seating plane Shield Heat-absorbing board, (1.5 ±0.5) mm thick, between capacitor body and liquid solder Evaluation criteria: Visual inspection ∆C/C0 tan δ Please read Cautions and warnings and Important notes at the end of this document.
B32651 ... B32656 High pulse (wound) 1.3 General notes on soldering Permissible heat exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical characteristics.
B32651 ...
B32651 ... B32656 High pulse (wound) 3 Embedding of capacitors in finished assemblies In many applications, finished circuit assemblies are embedded in plastic resins. In this case, both chemical and thermal influences of the embedding ("potting") and curing processes must be taken into account.
B32651 ... B32656 High pulse (wound) Cautions and warnings Do not exceed the upper category temperature (UCT). Do not apply any mechanical stress to the capacitor terminals. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after it has been soldered to the PC board. Do not pick up the PC board by the soldered capacitor. Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified lead spacing.
B32651 ... B32656 High pulse (wound) Topic Safety information Soldering Do not exceed the specified time or temperature limits during soldering. Cleaning Use only suitable solvents for cleaning capacitors. Embedding of When embedding finished circuit assemblies in capacitors in plastic resins, chemical and thermal influences finished assemblies must be taken into account.
B32651 ...
B32651 ...
B32651 ...
Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned.
