SMT inductors SIMID series, SIMID 1210-H Series/Type: B82422H Date: December 2012 a~í~=pÜÉÉí ¤ EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
SMT inductors, SIMID series B82422H SIMID 1210-H Size 1210 (EIA) or 3225 (IEC) Rated inductance 0.1 ... 680 μH Rated current 61 ...
SMT inductors, SIMID series B82422H SIMID 1210-H Dimensional drawing and layout recommendation 1.9±0.1 1) A 0.6±0.2 1) B C D B IND0053-6 2.2±0.2 0.45 min.1) 3.2±0.2 0.15 max. A B C D 2.7 1.15 2.1 4.4 2.5±0.2 Marking 1) Soldering area Dimensions in mm IND0496-P-E Taping and packing Reel <_ 2.8 4±0.1 _0 8.4 +1.5 1.0+0.2 _0 12.75 +0.15 _2 330 +0 8±0.3 2±0.05 _2 180 +0 1.5+0.1 <_ 4.2 Component 14.4 max. 3.5±0.05 4±0.1 1.75±0.1 Blister tape 62±1.
SMT inductors, SIMID series B82422H SIMID 1210-H Technical data and measuring conditions Rated inductance LR Measured with impedance analyzer Agilent 4294A at frequency fL, 0.
SMT inductors, SIMID series B82422H SIMID 1210-H Characteristics and ordering codes Tolerance LR PH fL Qmin MHz 1.0 r5% 1.5 r10% IR Rmax fres,min MHz mA : MHz Ordering code 1)2) ( 180-mm reel) 7.96 10 2.52 1150 0.10 150 B82422H1102+000 7.96 10 2.52 900 0.14 110 B82422H1152+000 2.2 7.96 10 2.52 800 0.16 90 B82422H1222+000 3.3 7.96 10 2.52 770 0.18 70 B82422H1332+000 4.7 7.96 10 2.52 700 0.25 46 B82422H1472+000 6.8 7.96 10 2.52 570 0.
SMT inductors, SIMID series B82422H SIMID 1210-H Inductance L versus DC load current IDC measured with LCR meter Agilent 4284A, typical values at +20 °C Impedance |Z| versus frequency f measured with impedance analyzer Agilent 4294A/E4991A, typical values at +20 °C IND0499-X 10 6 Ω B82422H |Z| IND0608-P 10 3 μH B82422H 680 μH L 10 5 100 μH 10 2 10 4 10 μH 10 1 10 3 1 μH 10 0 10 2 680 μH 100 μH 10 μH 1 μH 0.
Cautions and warnings ■ Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing.
Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned.