SMT inductors SIMID series, SIMID 1210-H Series/Type: B82422H Date: February 2020 Data Sheet ¤ TDK Electronics AG 2020. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics’ prior express consent is prohibited.
SMT inductors, SIMID series B82422H SIMID 1210-H Size 1210 (EIA) or 3225 (IEC) Rated inductance 1 ... 680 μH Rated current 61 ...
SMT inductors, SIMID series B82422H SIMID 1210-H Dimensional drawing and layout recommendation A B C D 2.7 1.15 2.1 4.4 Dimensions in mm Taping and packing Blister tape Reel A Please read Cautions and warnings and Important notes at the end of this document. 3 02/20 330 mm reel 180.0 +0/–3 330.0 r2.0 C 13.0 +0.5/–0.2 13.0 +0.5/–0.2 N 60.0 r1.0 W1 Dimensions in mm 180 mm reel W2 8.4 +1.5/–0 14.4 max 75.0 +1.0/–3.0 8.4 +1.5/–0 14.
SMT inductors, SIMID series B82422H SIMID 1210-H Technical data and measuring conditions Rated inductance LR Measured with impedance analyzer Agilent 4294A and test fixture Agilent 16034H or equivalent at frequency fL, RMS voltage 0.1 V, +(23 r5) °C Q factor Qmin Measured with impedance analyzer Agilent 4294A and test fixture Agilent 16034H or equivalent at frequency fQ, RMS voltage 0.
SMT inductors, SIMID series B82422H SIMID 1210-H Characteristics and ordering codes Tolerance LR PH 1.0 fL, fQ Qmin MHz r10% Isat,typ Isat,min IR Rmax mA mA mA : fres,min Ordering code 1)2) MHz ( 180-mm reel) 7.96 8 1835 1620 1150 0.10 150 B82422H1102K000 1.5 7.96 8 1520 1375 960 0.13 110 B82422H1152K000 2.2 7.96 8 1350 1220 890 0.15 90 B82422H1222K000 3.3 7.96 8 1150 1040 790 0.18 70 B82422H1332K000 4.7 7.96 8 905 815 700 0.
SMT inductors, SIMID series B82422H SIMID 1210-H Impedance |Z| versus frequency f measured with impedance analyzer Agilent E4991A, typical values at +20 °C Inductance L versus DC load current IDC measured with LCR meter Agilent 4285A, typical values at +20 °C Q factor versus frequency f measured with impedance analyzer Agilent 4294A, typical values at +20 °C Current derating Iop/IR versus ambient temperature TA (rated temperature TR = +105 °C) Please read Cautions and warnings and Important notes at t
Cautions and warnings ■ Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing.
Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned.
Important notes 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements.
