Datasheet
22
Pleas e read Important notes on page 4 and Cautions and warnings on page 69.
B i tte beachten Sie d i e S e i te 4 Wichtige Hinweise s owi e d i e
Warn- und Sicherheitshinweise auf S e i te 69.
© EPCOS AG 2008
Function
Funktion
Function
Failsafe function
In the cas e of i nfluencessuch a s a d i rect contact between
the power and telecommuni cati on l i nes , current w i ll flow
through the i gni ted arre s ter for a long peri od of t i me. The
arre s ter then heats up. When this happens , the hardware
mus t be protected from thermal overload. The heati ng is
detected by a fai l s afe mechanism . The s pacer ( s older pel-
let or plas t i c foi l), whi ch i n i t i ally k eeps the s hort-ci rcu i t
s pri ng at a d istance from the electrodes
, melts at a tem-
perature determi ned by the choi ce of materi al u s ed. The
s hort-ci rcu i t s pri ng, to whi ch a b i a s tension is appli ed,
then drops onto the arre s ter body and s hort-ci rcu i t s the
electrodes.
Figure 18 s hows a typi cal s hort-ci rcu i t characterist i c a s a
functi on of the current flowi ng through the arre s ter. This
characterist i c can be affected by the thermal conducti v i -
ty of the holder. The coord i nati on between component
and pack age mus
t therefore be s ubs equently veri f i ed by
a type tes t .
Note: The materi als u s ed i n the s ens or for moni tori ng the ar-
res ter‘s temperature are tri ggered at temperature s above 200 °C
( s older) or 140 °C/260 °C (plas t i c foi l) dependi ng on thei r com-
posit i on. The melti ng temperature s of the s older or plas t i c foi l are
up to 300 °C. Thes e temperature s exceed the melti ng poi nt of
s tandard commerc i al s oft s olders u s ed i n further processing.
This d iscrepancy mus t be considered when deci d i ng on the lo-
cati on of the arre s ter, whi ch may have to be addi t i onally s ecured
by mechani cal means. The thermal radi ati on to adj acent com-
ponentsis another factor of i mportance.
Kurzschlussmechanismus
Bei Beei nflussungen z. B . durch d i e d i rek te Berührung
z w ischen S tromnetz und Nachri chtenlei tung k ann über
längere Zei t e i n S trom durch den gez ündeten Ablei ter
fli eßen. D i e s er S trom führt z u e i ner Erwärmung des Ablei -
ters. Für d i e s en Fall muss d i e Hardware gegen thermi -
s che Überbelas tung ges chütz t werden. D i e Wärme w i rd
durch e i nen K urzschlussmechanismus
detek t i ert. E i ne
Lotpi lle oder e i ne K uns t s tofffoli e halten d i e K urzschluss-
feder z unächs t auf Abs tand z u den Elek troden b is sie bei
e i ner durch d i e Materi alaus wahl vorbes t i mmten Tempe-
ratur s chmelz en. D i e m i t Vor s pannung aufges etz te K urz -
s chlussfeder s enk t sich auf den Ablei terk örper ab und
s chli eßt d i e Elek troden k urz.
Bild 18: Typ ischer Verlauf e i ner K urzschlusskennli n i e i n
Abhängi g k e i t vom S trom, der durch den Ablei ter fli eßt.
D i e s e Charak terist ik k ann durch d i e Wärmelei tfähi g k e i t
der Fassung beei nflusst werden. Daher ist abs chli eßend
d i e K oord i nati on durch e i ne Typprüfung nachz uweisen.
Hinweis: D i e alsSens or z ur Temperaturüberwachung des Ab-
lei ters verwendeten Materi ali en lös en, j e nach Wer kstoff, ers t bei
Temperaturen über 200 °C (Lotformtei l) b z w . 140 °C/260 °C
( K uns t s tofffoli e) aus. D i e S chmelz temperaturen der verwendeten
Lotpi lle oder der K uns t s tofffoli e betragen b is z u 300 °C. D i e s e
Temperaturen übers chre i ten j edoch den S chmelz punk t handels -
übli cher Wei chlote, w i e sie bei der Montage der Ablei ter Verwen-
dung f i nden. Bei der E i nbaulage des Ablei tersis t d i e szu berück -
sichti gen und der Ablei ter gegebenenfallszu s ätz l i ch mechanisch
z u sichern . Beachtet werden
muss ebenfalls d i e Wärmeabs trah-
lung auf benachbarte Bautei le.
Failsafe characteristic
Auslöseverhalten des Kurzschlussmechanismus
RAB0217-V
A
s
Time to short-circuit / Auslösezeit
Fig. / Bild 18
Ueberspannungsableiter_de-en_2009.qxd 03.11.2008 16:19 Uhr Seite 22