Epson PowerLite 1700c/1710c Multimedia Projector ® ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 8 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 10 Optional Accessories . .
2 Using the Remote Control . . . . . . . . . . . . . . . . . . . 25 Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Replacing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 26 Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 27 Switching Between Picture Sources . . . . . . . . . . . . . . . . 27 Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 28 Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fine-Tuning the Projector . . . . . . . . . . . . . . . . . . . 43 6 Maintaining the Projector . . . . . . . . . . . . . . . . . . . 57 7 Solving Problems Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 45 Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .
A Projector Installation . . . . . . . . . . . . . . . . . . . . . . . . 79 B Technical Specifications . . . . . . . . . . . . . . . . . . . . . 81 C Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 87 Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . . 89 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . 90 FCC Compliance Statement. .
- Welcome The Epson PowerLite ® ® 1700c/1710c is an easy-to-use projector that weighs less than 4 pounds. The projector offers up to 2700 lumens (1710c) or 2200 lumens (1700c) of brightness. You can connect it to a wide range of computers and video sources. Easy control The projector’s keystone correction feature automatically corrects image distortion, and you can use the remote control to take charge of your presentation from almost anywhere in the room.
Using Your Documentation This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector. ■ Tips contain additional projection hints.
■ presentersonline.com Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Club®—and it’s free.
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: PDF manual and registration CD-ROM Projector Remote control and 2 AAA batteries Audio adapter Carrying case Power cable VGA computer cable Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location. If you are moving the projector by hand, use the carrying case.
Optional Accessories To enhance your use of the projector, Epson provides the following optional accessories: Product Part number Replacement lamp V13H010L38 Air filter replacement set (2 filters) V13H13408 ATA molded hardshell case Samsonite® wheeled soft case Notebook/projector soft shoulder bag Soft carrying case ELPKS54 ELPKS35-S ELPKS43 ELPKS16B Universal ceiling mount False ceiling plate Security bracket/cabling for gyro lock mounts Adjustable ceiling channel Suspension adapter ELPMBUNI ELPMB
Welcome
1 Displaying and Adjusting the Image W hether you’re presenting from a computer or video equipment, you need to follow some basic steps to display your image on the screen.
Positioning the Projector note You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 79 for details. If the projector isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.
Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be at about the level of the bottom of the screen. note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector. You can purchase this from Epson; see page 11.
Follow these steps to turn on the projector: note To shut down the projector, see page 23. Shutting down the projector correctly prevents premature lamp failure and possible damage from overheating. 1. Open the A/V Mute slide (lens cover). 2. Plug one end of the power cable into the projector, and the other end into an electrical outlet. The Power light turns orange.
3. Press the red P Power button on the remote control or on top of the projector. The projector beeps once and the Power light flashes green as the projector warms up, then an image begins to appear. When the Power light stops flashing and remains green, the projector is ready for use. 4. If you’ve connected a Windows-based computer to the projector, you may see a New Hardware Wizard screen saying your computer has found a plug-and-play monitor; if so, click Cancel.
Troubleshooting Display Problems Follow these guidelines if you’re having trouble displaying an image. You Can’t Project an Image If you don’t see the image you are trying to project, try the following: ■ Make sure the cables are connected correctly, as described beginning on page 33. ■ Make sure the Power light is green and not flashing and the A/V Mute slide is open.
■ If the function key doesn’t permit you to display simultaneously on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control Panel, open the Display utility. In the Display Properties dialog box, click the Settings tab, then click Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled.
Adjusting the Image Once you see your image, you need to make certain adjustments: ■ If the image is too high or too low, you can reposition it. See below. ■ To focus or zoom your image, see page 21. ■ If the image isn’t square, see page 21. ■ If a computer image displays incorrectly, see page 23. ■ If you need to fine-tune the image and/or sound, see Chapter 4. Adjusting the Height of Your Image If the image is too low on the screen, you can use the front adjustable foot to raise it. 1.
Focusing and Zooming Your Image Turn the focus ring on the projector to sharpen the image. Turn the zoom ring on the projector to reduce or enlarge the image. Focus Zoom If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 29 for instructions.
Using Keystone Correction To adjust your image when it is wider on the top or bottom, do the following: ■ Press one of the two triangular buttons on the projector’s control panel, as shown below. Continue pressing the button until you are satisfied with the shape of the image. ■ Or press the Menu button on the remote control or projector, select the Setting menu, and press Enter. note The image will be slightly smaller after adjusting.
Correcting Computer Images If you’re connected to a computer and the image doesn’t look right, press the Auto button on the remote control or the Enter button on the projector. This automatically resets the projector’s tracking, sync, resolution, and position settings. note You must be projecting an image for this button to have any effect. The Auto button works only with computer images projected through the VGA port.
note You can set the projector to automatically turn off the projector lamp and enter “sleep mode” when it has not received any signals for 30 minutes. This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the P Power button. If you are done using the projector, unplug the power cord. To enable sleep mode, see page 56. 3. Press the P Power button again. The lamp turns off.
1 Using the Remote Control T he projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 20 feet away. note For information and resources to help you give the most professional presentation, be sure to visit presentersonline.com. You can use the remote control to adjust the picture and sound (page 27) or as a pointer to highlight your presentation (page 32).
note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes. Using the Remote Control Follow these tips for using the remote control: ■ Point the remote control at the front of the projector or at the screen. ■ Stand within 20 feet of the projector. ■ Avoid using the remote under bright fluorescent lamps or in direct sunlight, or the projector may not respond properly.
Controlling the Picture and Sound You can use the remote control to preview and select your picture sources, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, and adjust the volume.
Turning Off the Picture and Sound You can use the A/V Mute button on the remote control to turn off the image and sound. This feature is useful if you want to temporarily redirect your audience’s attention. ■ To turn off the picture and sound, press the A/V Mute button. The screen turns black. ■ To turn the image and sound back on, press the button again. You can have the screen turn blue when you press the A/V Mute button.
Zooming Part of Your Image You can zoom in on a portion of the image using the E-Zoom buttons on the remote control. 1. Press the E-Zoom button on the remote control. You see a crosshair indicating the center of the zoom-in area. 2. Use the pointer button to position the crosshair. button to enlarge the selected 3. Continue pressing the E-Zoom area up to 4 times. 4. While the image is enlarged, you can: ■ Use the pointer button to move around the screen. ■ Press the E-Zoom button to zoom out. 5.
Resizing Video Images You can use the Resize button on the remote control to adjust how an image fits into the display area. For video images, press Resize to switch the aspect ratio between 4:3 and 16:9, (and Normal for computer images). This lets you play certain digital video images or movies recorded on certain DVDs in 16:9 widescreen format. For computer images, resizing is normally unnecessary, since the projector automatically resizes the image to make the best use of the display area.
Operating Your Computer with the Remote Control If you connect a computer to the projector with a USB cable, as described on page 35, then select Link21L for the USB Type B setting in the Extended menu (see page 56), you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering slideshow-style presentations, since you won’t have to stand next to the computer to change slides. ■ Use the Up and slideshow.
Highlighting Your Presentation You can display a pointer to call out important information on the screen. If you want to customize the pointer tool, you can choose from three alternative shapes. Using the Pointer Tool 1. To activate the pointer tool, press the Pointer button on the remote control. A pointer appears on the screen. Pointer If you prefer to use a different style of pointer, see the instructions in the next section. 2.
1 Connecting to Computers and Other Equipment T his chapter tells you how to connect the projector to a notebook or desktop computer, and/or to video equipment, such as a VCR, DVD player, or video camera.
note If you connect a Windowsbased computer to the projector, you may see a New Hardware Wizard saying your computer has found a plug-and-play monitor; if so, click Cancel. note For newer notebooks with DVI connectors, see your computer’s documentation to see how to use a DVI to VGA adapter (often included with the computer) to connect to the VGA computer port.
3. When you’ve finished making any connections, see page 15 for instructions on turning on the projector and adjusting the image. Connecting the Cable for Remote Mouse Control If you’ve connected a computer as described in this chapter (using the Computer/Component Video port) and set the USB Type B setting under the projector’s Extended menu to Link21L (see page 56), you can use the projector’s remote control as a wireless mouse.
4. If necessary, configure your computer to work with an external USB mouse. See your computer documentation for details. Connecting to Video Equipment RCA connector (composite video) S-Video connector You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections: ■ If your video player has a yellow RCA-style video output connector, see “Connecting a Composite Video Source” on page 37.
Connecting a Composite Video Source 1. Locate an RCA-style video cable (one is usually provided with your video equipment or you can purchase one from an electronics dealer). 2. Connect the cable to the yellow video output connector on your player and the yellow Video connector on the projector: 3. If you want to play sound through the projector, see page 40 for instructions on connecting audio cables. 4.
Connecting an S-Video Source 1. Locate an S-Video cable (one is usually provided with your video equipment or you can purchase one from Epson; see page 10). 2. Connect the cable to the S-Video connector on your player and the S-Video connector on the projector: 3. If you want to play sound through the projector, see page 40 for instructions on connecting audio cables. 4.
Connecting a Component Video Source You will need a component-to-VGA video cable or a component video-to-VGA adapter for this connection. You can order this cable (ELPKC19) from Epson; see page 11 for more information. 1. Locate a component-to-VGA video cable or adapter. 2. Connect the cable to your player and the blue Computer/Component Video connector on the projector. note Be sure your video player is not an RGB video source. If you select the wrong source, image quality may suffer.
Connecting an RGB Video Source note 1. Locate the VGA computer cable provided with the projector. Be sure your video player is 2. Connect the cable to the video port on your player and the Computer/Component port on the projector. not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation. 3. If you want to play sound through the projector, see page 40 for instructions on connecting audio cables. 4.
■ If you have a computer connected to the blue Computer/ Component Video port, use a stereo mini-jack cable. ■ If you have video equipment connected to the Video or S-Video port, use an RCA-style audio cable and the audio adapter included with the projector. Audio adapter 2. Connect the other end of the cable to the audio output connector(s) on your computer or video equipment.
Connecting to Computers and Other Equipment
1 Fine-Tuning the Projector Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options note The Network option does not appear in the 1700c/1710c menu. Menu list The menus are listed on the left and the options available for the highlighted menu are shown on the right. 2.
4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the Enter button to view a sub-screen for changing the setting. ■ Press the left or right side of the a slider bar. pointer button to adjust ■ To select from two or more settings, use the pointer button to highlight the desired setting and press Enter. 5.
Adjusting the Image You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast. 1. Press the Menu button on the projector or remote control and select the Image menu. You see the Image menu screen. 2. Use the pointer button to highlight the desired option, then adjust it as needed: ■ Color Mode Lets you quickly adjust the color and brightness for various environments. Use either the remote control or the Color Mode setting in the Image menu.
Blackboard: For projecting accurate colors on a green chalkboard (adjusts the white point). note The Brightness setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness. Select Brightness Control in the Setting menu, then choose High or Low (the default setting is High). Customized: For manual color adjustment. (See below.) ■ Brightness Lightens or darkens the overall image. ■ Contrast Adjusts the difference between light and dark areas.
You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.) Computer/RGB Video Component Video Composite Video/S-Video 2. Use the pointer button to highlight the desired option, then adjust it as needed: ■ Leave this setting On to automatically optimize the computer image. Turn it off if you want to save adjustments you have made to the video settings.
■ Video Signal Leave this setting at Auto unless you are using a 60-Hz PAL system (then select PAL60). ■ Resize Choose an aspect ratio of either 4:3 or 16:9. Normal is the default setting for a computer connection. Customizing Projector Features You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features. ■ Keystone Squares up the shape of the image after the projector has been tilted upward.
■ Brightness Control Lets you select from two levels of brightness. The Low setting reduces power consumption and noise, and extends the lamp’s operating life. ■ note Volume Raises or lowers the volume of the projector’s speaker. You can also adjust the volume using the remote control. Using the Projector Security Features To prevent unauthorized use of the projector, you can do the following: note It’s a good idea to write down your password.
The default setting for the Password Protect function is Off. Follow these steps to turn password protection on: 1. Press the Freeze button on the remote control for about five seconds. You see this screen: caution 2. Use the pointer button to set Power On Protect to On. Then press Enter. 3. Press Esc. If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times. 4. Select Password and press Enter. 5.
The countdown for the elapsed time begins as soon as you close the Password Protect menu. (You can check the elapsed time in this menu next to Time elapsed.) 10. To enable your screen logo, select User’s Logo Protect and press Enter. Select On and press Enter. When this feature is on, the logo appears whenever you turn on the projector (if the Startup Screen is enabled in the Extended menu; see page 53).
If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked. Request code xxxxx and the projector switches to standby mode for approximately 5 minutes. Write down the request code. Then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.
2. Highlight User’s Logo and press Enter. 3. When you see a message asking Choose this image as the user’s logo?, select Yes and press Enter. A selection box displays over the image. 4. Use the pointer button to select the area of the image you want to use. Then press Enter. 5. When you see the message Select this Image?, highlight Yes and press Enter. 6. Use the arrow buttons to select a zoom rate (display size) and press Enter. 7.
2. Select Display and press Enter. 3. Highlight Display Background (for when there is no signal) or A/V Mute, and press Enter. 4. Select Logo and press Enter. 5. When you’re finished, press Esc to exit. Disabling the Projector’s Buttons note When you enable the Operation Lock function, you can lock all the projector’s buttons, or all buttons except the Power button. 1. Press the Menu button, highlight the Settings menu, and press Enter.
■ Display Use this setting to turn off the display of messages, change the background color, enable logo display, or turn off the startup screen display. ■ User’s Logo Create a custom startup screen, as described on page 53.
1 Maintaining the Projector Y our projector needs little maintenance. All you have to do is keep the lens clean and periodically clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. Use a canister of compressed air to remove dust. To remove dirt or smears on the lens, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens. Cleaning the Projector Case caution Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case. 58 Before you clean the case, turn off the projector and unplug the power cord.
Cleaning the Air Filter and Vent Clean the air filter and air intake vent after every 100 hours of use. If they are not cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. note To order replacement air filters, request part number V13H13408. See page 11 for ordering information. Follow these steps: 1. Turn off the projector. Wait for the Power light to stop flashing, then unplug the power cord. 2.
Replacing the Lamp and Air Filter note When you get a replacement lamp for your projector, you should replace the filter. The life span of the projection lamp is about 2000 hours if Brightness Control in the Setting menu is set to High (default), and 3000 hours if Brightness Control is set to Low. To check how long the lamp has been in use, see page 69. It is time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate.
4. Loosen the lamp cover screw (you don’t need to remove it). Then slide the lamp cover to the side and lift it off of the projector. 5. Loosen the two screws holding the lamp in place (you can’t remove them). Loosen, but don’t remove these screws note 6. Hold the lamp as shown and pull it straight out. The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp.
8. Push down the corner marked PUSH until it snaps in. 9. Once the lamp is fully inserted, tighten its screws. 10. Replace the lamp cover, then tighten its screw. 11. Turn the projector over. 12. Slide the air filter out and remove it. 13. Slide in the new air filter until it clicks in place. 14. Reset the lamp timer as described in the next section.
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menus. 1. Press the Menu button on the remote control or on the projector’s control panel. You see the main menu. 2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight Reset, then press Enter. You see this screen: 3. Select Reset Lamp Hours and press Enter. 4. When you see the prompt, select Yes and press Enter. 5.
Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent damage: note ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector. ■ When transporting the projector a long distance, first place it in a hard-shell shipping case, then pack it in a firm box with cushioning around the case.
1 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue ? Help button on top of the projector or on the remote control. The following choices are available: ■ ”No Signal.” or no image appears on the screen ■ There is no sound ■ Select a different language Follow these steps to get help: 1. Press the blue ? Help button on the remote control or on the projector. You see the Help Menu. 2.
Checking Projector Status If your projector isn’t working correctly, first turn it off, wait for it to cool (the Power light stops flashing orange), and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status.
Status lights (continued) Light Status Description Flashing red There is a problem with the fan or temperature sensor. Stop using the projector, disconnect the power cable, and contact Epson as described on page 76. Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filters and vents are clear.
Viewing Lamp Usage and Other Information Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used. Press the Menu button and highlight the Info menu. You see the lamp usage hours and various input signal settings on the right. The life span of the lamp is about 2000 hours if the Brightness Control setting in the Setting menu is set to High (default), and 3000 hours if the Brightness Control setting is set to Low.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the Power light is green, not flashing. ■ The projector may be in standby or sleep mode. If the Power light is orange, press the P Power button to turn the projector on. ■ If the power was switched off and then on again, the projector may be cooling down. Wait until the Power light stops flashing and remains orange; then press the P Power button again.
If you’re using a PC notebook: ■ Hold down the Fn key on the keyboard and press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your notebook’s manual or online help for details. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
■ Press the Resize button on the remote control. ■ Press the Esc button on the remote control to cancel the E-Zoom function. ■ Make sure your computer’s resolution setting is correct. Ideally, it should be 1024 × 768 to match the projector’s native resolution. If this option isn’t available, select one of the other compatible video formats listed on page 83. ■ ■ Windows: Right-click the desktop, select Properties, click the Settings tab, and select a different resolution.
■ The video signal may be split between the computer and the projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your notebook computer and the projector, turn off the notebook’s LCD display. ■ Make sure the correct input signal is selected in the Signal menu (see page 49). The image is blurry. ■ There may be dirt or smears on the lens. Clean the lens as described on page 58. ■ Adjust the focus using the focus ring (see page 21).
2. Adjust the Tracking to eliminate vertical bands. 3. Adjust the Sync setting to increase the image sharpness. The image is too light or dark, or colors are incorrect. note Because of the different technologies used, your projected image may not exactly match the colors on your notebook or computer monitor. ■ If you’re displaying a computer image, use the Color Mode option in the projector’s Image menu to adjust the color (see page 46).
■ Try adjusting the Volume setting in the Setting menu (see page 50). ■ If you’re using a VCR or other video source, make sure the volume is not turned all the way down or muted. Also, make sure the cables are connected correctly, as described on page 40. ■ If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted.
■ If any buttons are held for longer than 30 seconds, the remote enters sleep mode. Release any button that is held to wake the remote. Where To Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website at http://support.epson.com and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Visit http://www.presentersonline.
■ Proof of purchase (such as a store receipt) and date of purchase ■ Computer or video configuration ■ Description of the problem Purchase Supplies and Accessories You can purchase screens, carrying cases, or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Solving Problems
A Projector Installation T his appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt the projector down to position the image on the screen. This causes the image to lose its square shape. You can correct the distortion using the Keystone function in the projector’s menu system (see page 49). If you place the projector so that the base of the lens is level with the bottom of the screen, the image should be square and you won’t have to adjust it.
A Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 16.8 million colors Brightness 1700c 2200 lumens (High Brightness mode) 1700 lumens (Low Brightness mode) 1710c 2700 lumens (High Brightness mode) 2100 lumens (Low Brightness mode) Contrast ratio 400:1 Image size 30 to 300 inches Projection distance 3.2 to 39.7 feet (1.0 to 12.
Projection Lamp Type UHE (Ultra High Efficiency) Power consumption 170 W Lamp life Approx. 2000 hours (High Brightness mode) Approx. 3000 hours (Low Brightness mode) Part number V13H010L38 Remote Control Range 20 feet (6 meters) Batteries (2) Alkaline AAA Dimensions Height 2.7 inches (68 mm), feet retracted Width 10.7 inches (273 mm) Depth 7.6 inches (193 mm) Weight 3.5 lb (1.6 kg) Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC, 2.7 A 200 to 240 VAC, 1.
Environmental Temperature Humidity (non-condensing) Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Operating: 20 to 80% RH Storage: 10 to 90% RH Operating altitude 0 to 7,500 ft (0 to 2,286 m) Safety United States FCC 47CFR Part 15B Class B (DoC) UL60950 Third Edition Canada ICES-003 Class B CSA C22.2 No. 60950 CE Marking Directive 73/23/EEC Directive 89/336/EEC IEC 60950 Third Edition EN 55022, EN 55024 Pixelworks™ DNX™ ICs are used in this projector.
Technical Specifications Mode Refresh Rate (Hz) Resolution VGA—60 VESA—72 VESA—75 VESA—85 60 72 75 85 640 × 480* 640 × 480* 640 × 480* 640 × 480* SVGA—56 SVGA—60 SVGA—72 SVGA—75 SVGA—85 56 60 72 75 85 800 × 600* 800 × 600* 800 × 600* 800 × 600* 800 × 600* XGA—60 XGA—70 XGA—75 XGA—85 60 70 75 85 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA1—70 SXGA1—75 SXGA1—85 70 75 85 1152 × 864* 1152 × 864* 1152 × 864* SXGA2—60 SXGA2—75 SXGA2—85 SXGA+60 SXGA+75 SXGA+85 60 75 85 60 75 85 1280 × 96
Mode Refresh Rate (Hz) Resolution HDTV (720p) HDTV (720p) HDTV (1080i) HDTV (1080i) 60 50 60 50 — — — — TV480i TV480i SDTV (480p) SDTV (480p) 60 50 60 50 — — — — *The image is resized using Epson’s SizeWise™ Technology.
Technical Specifications
A Notices This appendix includes safety instructions and other important information about your Epson PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.
■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards. ■ Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled into the projector, or if it has been exposed to rain or water.
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: ■ There is an object between the remote control IR emitter and the IR receiver on the projector. ■ Ambient light is too bright. ■ Certain types of fluorescent lighting are used. ■ A strong light source shines into the IR receiver.
Declaration of Conformity According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: Epson America, Inc. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806-2469 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Warranty Epson America, Inc. Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID.
Notices
Index A A/V Mute, 28, 54, 70 Accessories, 11 Adapter, audio, 10, 41 Air filter cleaning, 59 ordering, 11 replacing, 60 to 62 Altitude, 56, 83 Anti-theft device, 11, 15 Aspect ratio, 81 Audio adapter, 10, 41 controlling volume, 29 problems, troubleshooting, 74 to 75 turning off (using A/V Mute), 28 Auto button, 23 Auto Setup setting, 48 B Bands, vertical, 73 Blackboard color mode, 30, 47 Blackboard, projecting on, 30 Blank screen, 18 to 19 Blurry image, 73 Brightness, 81 Brightness setting, 47 C Cables ill
F L FCC compliance statement, 91 Filter, see Air filter Focusing image, 21 Freeze button, 28 Lamp number of hours used, 69 ordering, 11 replacing, 60 to 63 specifications, 82 status light, 67 to 68 Lamp timer, resetting, 63 Language setting, 56, 66 Laptop computer connecting to, 34 to 35 display problems, 18 to 19, 70 to 71 selecting source, 17, 27 Lens, cleaning, 58 Lights, status, 67 to 68 Logo, saving on projector, 53 to 55 G Game color mode, 30, 46 H HDTV images, video formats, 85 Height of image,
O Operation Lock setting, 55 Optical aspect ratio, 81 Options for projector, 11 P Password protection, 50 to 53 request code, 53 Photo color mode, 30, 46 Picture source, selecting, 17, 27, 37 to 40 Picture, see Image Pointer tool, using, 32 Positioning image, 20 projector, 14 to 15, 79 to 80 Power button, 17 specifications, 82 status light, 17, 67 to 68 Presentation color mode, 30, 46 Presentations computer, 23, 34 to 36 room conditions, 14, 26 tips and training, 9 using the pointer tool, 32 video, 36 to 4
Resize image, 30 Resolution, 30, 71, 81 S Safety instructions, 87 to 88 specifications, 83 Saturation setting, 47 Screen blank, 18 to 19 distance from projector, 14 ordering, 11 startup screen, creating, 53 to 54 Screen image, See Image Security Kensington lock, 11 password protection, 50 to 53 Sharpness setting, 47 Signal menu, 47 to 49 Sleep mode, 24 Sound troubleshooting, 74, 75 Source selecting, 17, 27, 38, 39 viewing, 69 Speaker, specifications, 81 Specifications brightness, 81 dimensions, 82 electric
W Warning lights, 67 to 68 Warranty, 9, 92 to 93 Windows display problems, 71 resolution setting, 72 Wireless, mouse, 31, 35 to 36 Z Zoom ratio, 81 Zooming image, 21, 29 Index 99
Index
