PowerLite® 1751/1761W/1771W/1776W User's Guide
Contents Introduction to Your Projector ................................................................................................................... 9 Projector Features................................................................................................................................ 9 Product Box Contents.................................................................................................................... 10 Additional Components ...........................................
Connecting to External USB Devices ............................................................................................ USB Device Projection.............................................................................................................. Connecting a USB Device or Camera to the Projector.............................................................. Selecting the Connected USB Source ......................................................................................
Remote Control Operation ................................................................................................................. Using the Remote Control as a Wireless Mouse ........................................................................... Using the Remote Control as a Presentation Pointer .................................................................... Selecting an Image Source ..........................................................................................................
Projector Identification System for Multiple Projector Control............................................................. Setting the Projector ID.................................................................................................................. Setting the Remote Control ID....................................................................................................... Matching Multiple-Projector Display Quality ........................................................................
Solutions When Image is Incorrect Using the USB Display Function .......................................... 134 Solutions When "No Signal" Message Appears........................................................................... 134 Displaying From a PC Laptop ................................................................................................. 135 Displaying From a Mac Laptop ...............................................................................................
Trademarks ...................................................................................................................................... Software Copyright........................................................................................................................... Copyright Notice............................................................................................................................... A Note Concerning Responsible Use of Copyrighted Materials......................
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
Product Box Contents Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Related concepts Projector Part Locations Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
1 Projector 2 Remote control 3 Remote control batteries (two AA alkaline) 4 Power cord 5 VGA computer cable 6 USB cable 7 Audio adapter cable (PowerLite 1776W) 11
8 Carrying case 9 Wireless LAN module (PowerLite 1761W/1771W/1776W) 10 EPSON Quick Wireless USB Connection Key (PowerLite 1776W) 11 Password Protected sticker 12 Projector documentation CD 13 Projector software CD 14 Wireless LAN module cover screw Parent topic: Projector Features Related concepts Projector Connections Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To receive a component video signal, you nee
Option or part Part number Wireless LAN module (ELPAP07) V12H418P12 Quick Wireless Connection USB key (ELPAP08) V12H005M08 EPSON DC-11 document camera (ELPDC11) V12H377020 EPSON DC-06 document camera (ELPDC06) V12H321005 BrightLink Solo interactive module (IU-01) V12H415020 Kensington security lock ELPSL01 Accolade Duet portable projector screen ELPSC80 ES3000 Ultra Portable Projection screen V12H002S3Y ES1000 Ultra Portable Tabletop Projection screen V12H002S4Y Component-to-VGA video ca
Warranty and Registration Information Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure that came with your projector. In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details.
• If you still need help after checking this manual and the sources listed above, you can use the EPSON PrivateLine Support service to get help fast. For details, see "Where to Get Help". Parent topic: Introduction to Your Projector Related references Where to Get Help Projector Part Locations Check the projector part illustrations to learn about the parts on your projector.
Projector Parts - Front/Top 1 Exhaust vent 2 Wireless LAN module indicator light (PowerLite 1761W/1771W/1776W) 3 Wireless LAN module cover (PowerLite 1761W/1771W/1776W) 4 A/V Mute slide lever 5 Foot release lever 6 Front adjustable foot 7 A/V Mute slide (lens cover) 8 Remote receiver 9 Projection distance/shape sensor (PowerLite 1776W) 10 Air intake vent (air filter) 16
11 Speaker 12 Projector status lights 13 Zoom ring 14 Focus ring (PowerLite 1751/1761W/1771W) 15 Control panel 16 Lamp cover Parent topic: Projector Part Locations Projector Parts - Rear 1 AC input port 2 Video port 3 Computer port 4 USB TypeB port 5 USB TypeA port 6 HDMI port 7 Audio port 8 Remote receiver 9 Lamp cover screw 10 Security lock port Parent topic: Projector Part Locations 17
Projector Parts - Base 1 Mounting bracket holes 2 Rear feet 3 Front adjustable foot 4 Wireless LAN module screw (PowerLite 1761W/1771W/1776W) Parent topic: Projector Part Locations 18
Projector Parts - Control Panel 1 Power button and light 2 Screen Fit button (PowerLite 1776W; adjusts projected images) 3 Source Search button (searches for connected video sources) 4 Enter button (selects options) 5 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 6 Help button (accesses projector help information) 7 Esc button (cancels/exits functions) 8 Horizontal keystone adjustment buttons (adjust screen shape) and arrow buttons 9 Menu button (accesses pro
Projector Parts - Remote Control 20
1 Power button 2 Computer button (cycles through connected computer sources) 3 Video button (cycles through connected video sources) 4 Screen Fit button (adjusts image shape; functions only on PowerLite 1776W and when not projecting from ceiling) 5 Focus buttons (adjusts the image focus; functions only on PowerLite 1776W) 6 Auto button (automatically adjusts position, tracking, and sync settings) 7 Aspect button (selects the image aspect ratio) 8 Num button (when held down, switches numeric b
26 USB button (cycles through connected USB sources) 27 Source Search button (searches for connected sources) 28 Remote control light (outputs remote control signals) Parent topic: Projector Part Locations Related tasks Connecting to a Computer for USB Mouse Control 22
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Cover Projector Placement You can place the projector on almost any flat surface to project your presentation. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings. Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image.
Screen or image size Projection distance 1 50 inches 44 to 53 inches (112 to 135 cm) 2 80 inches 71 to 85 inches (181 to 217 cm) 3 100 inches 89 to 107 inches (226 to 271 cm) 4 150 inches 134 to 161 inches (340 to 408 cm) Wide to Tele Parent topic: Projector Placement Related references Solutions When the Image is Fuzzy or Blurry Input Signal Settings - Signal Menu Image Quality Settings - Image Menu Related tasks Automatically Correcting Image Shape With Screen Fit Focusing the Image Cleanin
Connecting to External USB Devices Connecting to a Document Camera Parent topic: Setting Up the Projector Related references Projector Setup Settings - Extended Menu Product Box Contents Connecting to Computer Sources Follow the instructions in these sections to connect a computer to the projector.
• Windows XP: Wait as messages appear on your computer screen and the projector installs the EPSON USB Display software on your computer. • Windows 2000: Select Computer, EPSON_PJ_UD, and EMP_UDSe.EXE to install the EPSON USB Display software. • Mac OS X: The USB Display setup folder appears on your screen. Select USB Display Installer and follow the on-screen instructions to install the EPSON USB Display software. Follow any on-screen instructions.
Note: To connect a Mac that includes only a Mini DisplayPort or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port. Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through the HDMI port. 1. Connect the HDMI cable to your computer's HDMI output port. 2. Connect the other end to the projector's HDMI port.
Connecting to a Computer for Sound If your computer presentation includes sound and you did not connect it using the projector's USB TypeB or HDMI port, you can still play sound through the projector's speaker system. Just connect an optional 3.5 mm stereo mini-jack audio cable as described here. 1. Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or audio-out port. 2. Connect the other end to the projector's Audio port.
Parent topic: Connecting to Video Sources Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using a componentto-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable. 1. Connect the component connectors to your video source's color-coded component video output ports, usually labeled Y, Pb, Pr or Y, Cb, Cr.
Connecting to a Video Source for Sound You can play sound through the projector's speaker system if your video source has audio output ports. Connect the projector to the video source using a stereo mini-jack adapter cable (with one 3.5 mm miniplug and two RCA plugs). Note: You can also use an RCA cable connected to the audio adapter cable that came with your projector. 1. Connect the audio cable to your video source's audio-out ports. 2. Connect the other end of the cable to the projector's Audio ports.
• USB hard drive • Multimedia storage viewer • USB memory card reader Note: Digital cameras or camera phones must be USB-mounted devices, not TWAIN-compliant devices. You can also use the EasyMP PC Free feature to create your own slide shows containing converted PowerPoint files and image files, and project them from a connected USB device or memory card reader.
Related topics Projecting a Slide Show Selecting the Connected USB Source You can switch the projector's display to the source you connected to a USB TypeA port. 1. Make sure the connected USB source is turned on, if necessary. 2. Press the USB button on the remote control. 3. Press the button again to cycle through other USB sources, if available.
Parent topic: Projector Connections Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Open the battery cover as shown. 2. Insert the batteries with the + and – ends facing as shown.
3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Setting Up the Projector Opening the Lens Cover 1. To open the projector's lens cover, slide the A/V Mute slide lever. 2.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wireless Network Projection Setting Up Projector Network E-Mail Alerts Setting Up Monitoring Using SNMP Controlling a Networked Projector Using a Web Browser Wireless Network Projection You can send images to your projector through a wireless network PowerLite 1761W/1771W/1776W . To do this, you must install the EPSON 802.
Related references Optional Equipment and Replacement Parts Projector Network Settings - Network Menu Solutions When Network Alert E-Mails are Not Received Projector Setup Settings - Extended Menu Projector Network Settings - Network Menu Installing the Wireless LAN Module To use the PowerLite 1761W/1771W/1776W over a wireless network, install the EPSON 802.11b/g/n wireless module in the projector. Do not install any other type of wireless module.
3. Remove the wireless LAN module cover. 4. Insert the wireless LAN module into the port. 5. Replace the wireless LAN module cover, and then turn over the projector.
6. Secure the wireless LAN module cover using the screw you removed. 7. Plug in and turn on the projector. Parent topic: Wireless Network Projection Using Quick Wireless Connection (Windows Only) You can use the optional EPSON Quick Wireless Connection USB key to quickly connect the projector to a Windows computer wirelessly (PowerLite 1761W/1771W/1776W; USB key included with the PowerLite 1776W). Then you can project your presentation and remove the key when you are done. 1. Turn on the projector. 2.
4. Now connect the USB key to a USB port on your computer or notebook. Note: In Windows Vista, if you see the AutoPlay window, select Run LaunchU3.exe, then select Allow on the next screen. 5. Follow the on-screen instructions to install the Quick Wireless Connection driver. Note: If you see a Windows Firewall message, click Yes to disable the firewall. After a few minutes, your computer image is displayed by the projector.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Web Control Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web. • Projector Keyword lets you turn on a security password to prevent access to the projector by anyone not in the room with it.
Wireless LAN Menu Settings Note: See your projector's EasyMP Network Projection Operation Guide for details on selecting these settings.
Setting Options Description IP Settings DHCP (On or Off) Selects DHCP if your network assigns addresses automatically, or turns off DHCP so you can enter the network's IP address, subnet mask, and gateway address as needed IP Address Subnet Mask Gateway Address SSID Display On Selects whether to display the SSID on the network standby screen Off IP Address Display On Selects whether to display the IP address on the network standby screen Off Parent topic: Selecting Wireless Network Settings Manu
Parent topic: Wireless Network Projection Setting Up Wireless Network Security You can set up security for your projector to use on the wireless network (PowerLite 1761W/1771W/1776W). Set up one of the following security options to match the settings used on your network: • WEP encryption • WPA security Note: Check with your network administrator for guidance on entering the correct information. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3.
Parent topic: Wireless Network Projection Wireless Security Menu Settings Settings on the Security menu let you select the type of security and security settings that match the network you are connecting the projector to.
Parent topic: Setting Up Wireless Network Security Setting Up Projector Network E-Mail Alerts You can set up the projector to send you an e-mail alert over the network if there is a problem with the projector. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Mail menu and press Enter. 5. Turn on Mail Notification. 6. Enter the IP address for the SMTP Server option. Note: Do not use these addresses: 127.x.x.x or 224.0.0.
8. Choose an Address field, enter the e-mail address, and select the alerts you want to receive there. Repeat for up to three addresses. Note: Your e-mail address can be up to 32 alphanumeric characters long. 9. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
4. Select the Others menu and press Enter. 5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 6. If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to allow the projector to be detected. 7. If you are connecting to a network using Bonjour, turn on the Bonjour setting. 8.
Note: The web setup and control features support Microsoft Internet Explorer 6.0 or later, and Safari on networks that do not use a proxy server for connection. You cannot select all of the projector menu settings or control all projector functions using a web browser. Note: If you set Standby Mode to Communication On, you can use a web browser to select settings and control projection even if the projector is in standby mode.
3 Selects Video and HDMI port sources 4 Freeze button control 5 A/V Mute button control 6 Page Up and Page Down button controls 7 Searches for sources 8 Selects the network source 9 Selects the USB Display or USB device source 10 Volume button controls 11 Closed Caption control 6. Select the icon corresponding to the projector function you want to control.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. The projector's power light turns orange. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode). Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 4. Press the power button on the projector or the remote control to turn on the projector.
• Press the Source Search button on the projector or remote control to detect the video source. Parent topic: Using Basic Projector Features Related references Projector Setup Settings - Extended Menu Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown. Note: Turn off this product when not in use to prolong the life of the projector.
3. To transport or store the projector, make sure the power light is orange (but not flashing), then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange. 4. Close the projector's lens cover.
Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Extended menu and press Enter. Note: The Network menu does not appear on non-network projector models. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus.
2. To adjust the front foot, pull up on the foot release lever and lift the front of the projector. The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape.
Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality. When you turn on automatic keystone correction in your projector's Settings menu, your projector automatically corrects keystone effects when you reposition the projector.
1. Press the Screen Fit button on the projector or remote control. You see a message on the screen. 2. Move the projector as necessary to display the message in the middle of the screen. 3. Zoom into the image until its yellow frame extends beyond the edges of the screen. 4. Press the Screen Fit button again. Two displays flash briefly, then this message appears: 5. Fine-tune the image shape as necessary using the arrow buttons on the control panel. 6. When you are finished, press Esc.
Now, if necessary, you can correct the image corners individually using Quick Corner by pressing the arrow buttons on the control panel. Parent topic: Image Shape Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. Press the Menu button. 3.
6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter. 7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc. Parent topic: Image Shape Correcting Image Shape With the Keystone Buttons You can use the projector's keystone correction buttons to correct the shape of an image that is unevenly rectangular on the sides. 1. Turn on the projector and display an image.
2. Press a keystone button on the projector's control panel. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape using the Keystone settings in the projector menus.
Resizing the Image With the Zoom Ring 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. To enlarge or reduce the image size, rotate the projector's zoom ring. 1 PowerLite 1776W 2 PowerLite 1751/1761W/1771W Parent topic: Using Basic Projector Features Focusing the Image Before you sharpen the focus, turn on the projector and display an image.
1 PowerLite 1776W 2 PowerLite 1751/1761W/1771W Parent topic: Using Basic Projector Features Remote Control Operation The remote control lets you control the projector from almost anywhere in the room, up to 19.7 feet (6 m) away. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the angles listed here.
1 19.7 feet (6 m) 2 ±30º 3 ±60º Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
1. Connect the projector to a computer using the projector's USB TypeB, Computer, or HDMI port to display video. 2. If you connected your computer to the Computer or HDMI port, also connect a USB cable to the projector's USB TypeB port and to a USB port on your computer (for wireless mouse support). 3. Start your presentation. 4. Use the following buttons on the remote control to control your presentation: • To move through slides or pages, press the up or down Page buttons.
1. Press the Pointer button on the remote control. 2. Use the arrow buttons on the remote control to move the pointer on the screen. 3. Press Esc to clear the pointer from the screen. Parent topic: Remote Control Operation Related references Projector Feature Settings - Settings Menu Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other. 1.
• Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen.
Changing the Projection Mode Using the Menus You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus. 1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus.
Related references Image Quality Settings - Image Menu Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3. To cycle through the available aspect ratios for your input signal, press the Aspect button repeatedly.
Aspect ratio setting Description Normal Displays images using the full projection area and maintains the aspect ratio of the image. 4:3 Displays images using the full projection area at 4:3 aspect ratio. 16:9 Converts the aspect ratio of the image to 16:9. PowerLite 1761W/1771W/1776W Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the aspect ratio of the image.
Parent topic: Using Basic Projector Features Related references Image Quality Settings - Image Menu Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3.
Color Mode Description Photo Best for still images projected in a bright room Sports Best for television images in a bright room (video or composite video input only) sRGB Best for standard sRGB computer displays Blackboard Best for presentations onto a green chalkboard (adjusts the colors accordingly) Whiteboard Best for presentations onto a whiteboard (adjusts the colors accordingly) Customized Best for customizing a color mode using manual Color Adjustment settings in the Image menu DICOM S
3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and select On. Note: You can turn Auto Iris on or off for each Color Mode that supports the feature. You cannot change the Auto Iris setting when you are using a Closed Caption setting. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Controlling the Volume with the Volume Buttons You can use the Volume buttons on the remote control to adjust the volume as you project a presentation with audio.
A volume gauge appears on the screen. 3. To set the volume to a specific level for an input source, you can set the volume using the projector's menus. Parent topic: Using Basic Projector Features Related references Projector Feature Settings - Settings Menu Projecting a Slide Show You can use your projector's Slideshow feature whenever you connect a USB device that contains compatible image files.
• Project movies • Project PowerPoint presentations converted to "scenario" files using the EasyMP Slide Converter program included with your projector • Project .pdf files (PowerLite 1761W/1771W/1776W only) Note: For instructions on converting PowerPoint files to the necessary scenario file format, see the EasyMP Slide Converter Operation Guide on your projector CD.
File contents File type (extension) Details PDF .pdf Make sure the file is not: (PowerLite 1761W/1771W/ 1776W) Movie • Saved in PDF version 1.8 or later format • Encrypted .avi Make sure the file is not: • Saved with an audio codec other than PCM or ADPCM • Above 1280 × 720 resolution Parent topic: Projecting a Slide Show Starting a Slide Show or Presentation After connecting a USB device to the projector, you can switch to the USB input source and start your slide show or presentation.
2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional images in a folder, highlight Next page or Previous page and press Enter. 3.
2 Previous slide 3 Next slide or animation 4 Next slide or animation (animation effects are not played) 5 Previous slide or animation (animation effects are not played) 5. To stop the display, follow the on-screen instructions or press the Esc button. Slideshow Display Options Parent topic: Projecting a Slide Show Related tasks Disconnecting a USB Device or Camera From the Projector Slideshow Display Options You can select these display options when using the projector's Slideshow feature.
Setting Options Description Continuous Play On Displays a slide show continuously Off Displays a slide show one time through Screen Switching Time No Does not display the next file automatically 1 Second to 60 Seconds Displays files for the selected time and switches to the next file automatically Effect Wipe Transitions between images with a wipe effect Dissolve Transitions between images with a dissolve effect Random Transitions between images using a random variety of effects Parent t
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
Related references Projector Setup Settings - Extended Menu Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1. Press the Freeze button on the remote control to stop the video action. 2. To restart the video action in progress, press Freeze again.
You see a crosshair on the screen indicating the center of the zoom area. 2. Use the following buttons on the remote control to adjust the zoomed image: • Use the arrow buttons to position the crosshair in the image area you want to zoom into. • Press the E-Zoom + button repeatedly to zoom into the image area, enlarging it as necessary. • To pan around the zoomed image area, use the arrow buttons. • To zoom out of the image, press the E-Zoom – button as necessary.
Selecting Password Security Types Entering a Password to Use the Projector Saving a User's Logo Image to Display Parent topic: Projector Security Features Setting a Password To use password security, you must set a password. 1. Hold down the Freeze button on the remote control until you see the Password Protect menu. This takes about five seconds. PowerLite 1751 PowerLite 1761W/1771W/1776W 2. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?".
3. Select Yes and press Enter. 4. Hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5. Enter the password again. You see the message "Password accepted." 6. Press Esc to return to the Password Protect menu. 7. Make a note of the password and keep it in a safe place in case you forget it.
PowerLite 1761W/1771W/1776W If you do not see this menu, hold down the Freeze button on the remote control for five seconds until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protect, press Enter, select On, press Enter again, and press Esc. 2. To prevent changes to the User's Logo screen or related display settings, select User's Logo Protect, press Enter, select On, press Enter again, and press Esc. 3.
You must enter the correct password to use the projector. 1. Hold down the Num button on the remote control while you enter the password using the numeric buttons. The password screen closes. 2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact EPSON Support.
Related references Where to Get Help Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature). This transferred image is called the User's Logo screen.
You see the User's Logo zoom factor menu. 7. Select a zoom percentage and press Enter. You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. Note: It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished. You see a completion message. 9. Press Esc to exit the message screen. 10. Select the Extended menu and press Enter. 11. Select Display and press Enter. 12.
Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button. 1. Press the Menu button. 2. Select the Settings menu and press Enter. Note: The Split Screen option does not appear on PowerLite 1751 models. 3. Select the Control Panel Lock setting and press Enter. 4.
Parent topic: Locking the Projector's Buttons Installing a Security Cable You can use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson. 1 Security slot Parent topic: Projector Security Features Projector Identification System for Multiple Projector Control You can operate multiple projectors using one remote control for more elaborate presentations.
Setting the Projector ID If you want to control multiple projectors from a remote control, give each projector a unique ID. 1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select Projector ID and press Enter. 4. Use the arrow buttons on the remote control to select the identification number you want to use for the projector. Then press Enter. Repeat these steps for all the other projectors you want to operate from one remote control.
4. Hold down the ID button on the remote control while you press the numeric button that matches the projector's ID. Then release the buttons. 5. Press the ID button on the remote control to check if the ID-setting process worked. You see a message displayed by the projector. • If the remote control is listed as On, the remote control ID is set to operate only the listed projector. • If the remote control is listed as Off, the remote control ID is not set properly.
5. Press the Menu button, select the Extended menu, and press Enter. 6. Select the Multi-screen setting and press Enter. 7. Set the Adjustment Level setting to 1 and press Enter. 8. Set the remote control ID to match the second projector. 9. Access the Extended menu Multi-screen setting on the second projector and set the Adjustment Level setting to 1. 10. Adjust the Brightness Correct. setting on the projector with the darkest display so it matches the lighter display, and press Enter.
Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources next to each other. You can control the split screen feature using the remote control or the projector menus (PowerLite 1761W/1771W/1776W). Note: While you use the split screen feature, other projector features may not be available and some settings may be automatically applied to both images. 1. Press the Split button on the remote control.
5. To change the image sizes, select the Screen Size setting, press Enter, select a sizing option, press Enter, and press Menu to exit. Note: Depending on the video input signals, the images may not appear at the same size even if you choose the Equal setting. 6. To choose the audio you want to hear, select the Audio Source setting, press Enter, select an audio option, press Enter, and press Menu to exit. Note: Select Auto to hear audio from the largest screen or the left screen. 7.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Auto Iris On Adjusts the projected luminance based on the image brightness when certain Color Modes are selected Off Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode, use the Power Consumption setting. Parent topic: Adjusting the Menu Settings Related references Available Color Modes Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically.
Note: You can restore the default settings of the Position, Tracking, and Sync settings by pressing the Auto button on the remote control. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Progressive Off Sets whether to convert interlaced-to-progressive signals for certain video image types Video Film/Auto Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer graphics, and animation Noise Reduction Off Reduces flickering in analog images in two levels NR1 NR2 HDMI Video Range Normal Expanded Sets the video range to match the setting of the device connected to the HDMI input port Auto Input Signal Auto Specif
Setting Options Description Overscan Auto Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 4% 8% Parent topic: Adjusting the Menu Settings Related references Available Image Aspect Ratios Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
Setting Options Description Keystone H/V Keystone Adjusts image shape to rectangular (horizontally and vertically) Quick Corner H/V Keystone: lets you manually correct horizontal and vertical sides, or turn automatic correction (PowerLite 1776W) on or off Quick Corner: select to correct image shape and alignment using an on-screen display Split Screen Screen Size (PowerLite 1761W/1771W/1776W) Source Swap Screens Divides the viewing area horizontally and displays two images side-by-side (press Esc
Setting Options Description Volume Varying levels available Adjusts the volume of projector’s speaker system or external speakers Remote Receiver Front Limits reception of remote control signals by the selected receiver; Off turns off all receivers Rear Front/Rear Off User Button Power Consumption Info Assigns a menu option to the User button on the remote control for one-touch access Progressive Closed Caption Test Pattern Multi-screen Resolution Test Pattern On Displays a test pattern to ass
Solutions When the Image is Not Rectangular Solutions When the Image Brightness or Colors are Incorrect Image Quality Settings - Image Menu Input Signal Settings - Signal Menu Solutions to Projector Power or Shut-Off Problems Projector Light Status Solutions to Problems with the Remote Control Optional Equipment and Replacement Parts Remote Control Operation Related tasks Adjusting the Image Height Correcting Image Shape With the Keystone Buttons Using the Remote Control as a Presentation Pointer Controllin
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen A/V Mute Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Closed Caption Off Controls use of closed captions and se
Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Direct Power On: lets you turn on the projector without pressing the power button Sleep Mode Timer Lens Cover Timer High Altitude Mode Sleep Mode: automatically turns off the projector after an interval of inactivity Sleep Mode Timer: sets the interval for Sleep Mode Lens Cover Timer: automatically turns off the projector after 30 minutes if the lens cover is closed High Altitude Mode: regulates the p
Setting Options Description Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option) Parent topic: Adjusting the Menu Settings Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network (PowerLite 1761W/1771W/1776W).
Setting Options Description Net.
Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Information item Description Event ID Displays the Event ID number corresponding to a specific projector problem; see the list of Event ID codes (PowerLite 1761W/1771W/1776W) Event ID Code List Parent topic: Adjusting the Menu Settings Related references Optional Equipment and Replacement Parts Projector Lamp Specifications Event ID Code List If the Event ID option on the Info menu displays a code number, check this list of Event ID codes for the solution to the projector problem associated with the c
Event ID code Cause and solution 0891 Cannot find an access point with the same SSID. Set your computer, access point, and projector to the same SSID. 0892 The WPA/WPA2 authentication type does not match. Make sure the wireless network security settings are correct. 0893 The WEP/TKIP/AES encryption type does not match. Make sure the wireless network security settings are correct. 0894 Communication with unauthorized access point was disconnected. Contact your network administrator.
You cannot reset the following settings using the Reset All option: • Input Signal • User's Logo • Language • Network menu items (if available) • Lamp Hours • Language • Password • User Button • Multi-screen Parent topic: Adjusting the Menu Settings 116
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner to clean the lens, or you may damage it. Do not use canned air, or the gases may leave a residue.
2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Caution: Do not use canned air, or the gases may leave a residue. 3. If dust is difficult to remove or the air filter is damaged, replace the air filter.
2. Grasp the tab at the center of the air filter and pull it out of the projector. Note: Air filters contain polycarbonate, ABS resin, and polyurethane foam. Dispose of used air filters according to local regulations. 3. Place the new air filter in the projector as shown and push gently until it clicks into place.
Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover. Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury. 4. Slide the lamp cover out and lift it off.
5. Lift up the metal bar securing the lamp. 6. Lift up the lamp handle and gently pull the lamp out of the projector. Caution: Lift the lamp handle carefully to avoid damaging the handle as you pull out the lamp. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press down on the area shown to secure the lamp in place. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 8. Press the metal bar down over the lamp until it clicks into place on both sides.
9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage. Parent topic: Projector Lamp Maintenance Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter. You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual.
1. Open the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Operation Transporting the Projector The projector contains precision parts, some of which are glass.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solutions When Network Alert E-Mails are Not Received Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
1 Power light 2 Lamp light 3 Temperature light Power light Lamp light Temperature light Status and solution Green Off Off Normal operation. Flashing green Off Off Warming up. Wait for an image to appear. Orange Off Off Standby or sleep mode. Flashing orange Off Off Preparing network monitoring or shutting down. (Wait for the light to remain orange before unplugging the projector.) Flashing red Flashing orange Projector is too hot.
Power light Lamp light Temperature light Status and solution Red Off Red Projector has overheated and turned off. Leave it turned off to cool down for five minutes. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • If operating the projector at high altitude, turn on High Altitude Mode. • If overheating continues, replace the air filter. • If the problem persists, unplug the projector and contact Epson for help.
Related references Projector Setup Settings - Extended Menu Where to Get Help Related tasks Replacing the Lamp Replacing the Air Filter Cleaning the Air Filter and Vents Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 1. Turn on the projector. 2. Press the Help button on the projector or the remote control. You see the Help menu. 3. Use the up and down arrow buttons to highlight the problem you want to solve. 4.
Solutions When There is No Sound or Low Volume Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Make sure the lens cover is open or off. • Press the A/V Mute button on the remote control to see if the image was temporarily turned off. • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources. • Press the projector's power button to wake it from standby or sleep mode.
Solutions When Image is Incorrect Using the USB Display Function If no image appears or if the image appears incorrectly using the USB Display function, try the following solutions: • Press the USB button on the remote control. • Make sure the USB Display software has installed correctly. Install it manually if necessary. • Make sure the USB Type B setting in the Extended menu is set to USB Display, if available. • With Mac OS X, select the USB Display icon in the Dock or from the Applications folder.
Displaying From a PC Laptop If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor. 1. Hold down the laptop's Fn key and press the key labelled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear. 2. To display on both the laptop's monitor and the projector, try pressing the same keys again. 3.
Solutions When Only a Partial Image Appears If only a partial computer image appears, try the following solutions: • Press the Auto button on the remote control to optimize the image signal. • Try adjusting the image position using the Position menu setting. • Press the Aspect button on the remote control to select a different image aspect ratio. • If you zoomed into or out of the image using the E-Zoom buttons, press the Esc button twice to return to a full display.
Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector. They should be: • Separated from the power cord to prevent interference • Securely connected at both ends • Not connected to an extension cable • Check the settings on the projector's Signal menu to make sure they match the video source.
• Position the projector so the keystone adjustment angle is not so wide that it distorts the image. • When using the Screen Fit feature (PowerLite 1776W), position the projector at a compatible distance from the screen or adjust the image shape manually. • Turn on automatic keystone adjustment in the projector's menus. • Adjust the Sharpness setting to improve image quality. • If you are projecting from a computer, press the Auto button on the remote control to automatically adjust the tracking and sync.
Related concepts Projector Lamp Maintenance Related references Image Quality Settings - Image Menu Input Signal Settings - Signal Menu Projector Feature Settings - Settings Menu Solutions When There is No Sound or Low Volume If there is no sound when you expect it or the volume is too low, try the following solutions: • Adjust the projector's volume settings. • Press the A/V Mute button on the remote control to resume video and audio if they were temporarily stopped.
Solutions to Projector Power or Shut-Off Problems If the projector does not come on when you press the power button or it shuts off unexpectedly, try the following solutions: • Make sure the power cord is securely connected to the projector and to a working electrical outlet. • The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector. • The power cord may be defective. Disconnect the cord and contact Epson.
• If you assigned an ID number to the remote control to operate multiple projectors, you may need to check or change the ID setting (feature not available with all projectors). • If you lose the remote control, you can order another one from Epson.
Related references Projector Setup Settings - Extended Menu Projector Network Settings - Network Menu Where to Get Help If you need to contact Epson for technical support services, use the following support options. Internet Support Visit Epson's support website at www.epson.com/support (U.S.) or www.epson.ca/support (Canada) for solutions to common problems with your projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.
Technical Specifications These sections list the technical specifications of your projector.
PowerLite 1761W/1771W: Normal Power Consumption mode: White light output 2600 lumens (ISO 21118 standard) Color light output 2600 lumens ECO Power Consumption mode: White light output 1700 lumens (ISO 21118 standard) PowerLite 1776W: Normal Power Consumption mode: White light output 3000 lumens (ISO 21118 standard) Color light output 3000 lumens ECO Power Consumption mode: White light output 1700 lumens (ISO 21118 standard) Contrast ratio 2000:1 with Auto Iris on and Normal Power Consumption mode Image si
Zoom ratio 1:1.
Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Parent topic: Technical Specifications Related concepts Projector Lamp Maintenance Related references Projector Information Display - Info Menu Optional Equipment and Replacement Parts Remote Control Specifications Reception range 19.
Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% PowerLite 1751/1771W/1776W: 3.3 to 1.5 A PowerLite 1761W: 3 to 1.4 A Power consumption Operating: (110 to 120 V) PowerLite 1751W/1771W/1776W: Normal Power Consumption mode: 322 W ECO Power Consumption mode: 212 W PowerLite 1761: Normal Power Consumption mode: 293 W ECO Power Consumption mode: 212 W Standby: 0.38 W (Communication Off), 7.
Projector Environmental Specifications Temperature Operating: 41 to 95 ºF (5 to 35 ºC) Storage: 14 to 140 ºF (–10 to 60 ºC) Humidity (relative, noncondensing) Operating: 20 to 80% Operating altitude Up to 4921 feet (1500 m) Storage: 10 to 90% Up to 7500 feet (2286 m) with High Altitude Mode enabled Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 Canada ICES-003 Class B CSA C22.2 No.
Display format Refresh rate (in Hz) Resolution (in pixels) XGA 60/70/75/85 1024 × 768 WXGA 60 1280 × 768 WXGA 60 1360 × 768 WXGA 60/75/85 1280 × 800 SXGA 70/75/85 1152 × 864 SXGA 60/75/85 1280 × 960 SXGA 60/75/85 1280 × 1024 SXGA+ 60/75 1400 × 1050 WXGA+ 60/75/85 1440 × 900 WXGA++ 60 1600 × 1600 60 1600 × 1200 WSXGA+* ** 60 1680 × 1050 MAC13" 67 640 × 480 MAC16" 75 832 × 624 MAC19" 75 1024 × 768 MAC19" 59 1024 × 768 MAC21" 75 1152 × 870 TV (NTSC) 60 720
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 WXGA++ 60 1600 × 900 SXGA 60 1280 × 960 SXGA 60 1280 × 1024 SXGA+ 60 1400 × 1050 UXGA 60 1600 × 1200 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p)
Input Signal Settings - Signal Menu Related tasks Displaying From a Mac Laptop Displaying From a PC Laptop USB Display System Requirements Your computer system must meet the system requirements here to use the projector's USB Display software. Requirement Windows Mac Operating system Windows 2000 (Service Pack 4 only) Mac OS X 10.5.1 or later, 10.6.x, or 10.7.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Software Copyright Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to www.epson.com/recycle for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
• Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. Do not use canned air, or the gases may leave a residue.
• Before you move the projector, make sure its power is turned off, the plug is disconnected from the outlet, and all cables are disconnected. • Never try to remove the lamp immediately after use because it will be extremely hot. Before removing the lamp, turn off the power and wait at least an hour to allow the lamp to cool completely. • Do not disassemble the lamp or subject it to impacts. • Do not place the source of an open flame, such as a lit candle, on or near the projector.
Parent topic: Important Safety Instructions FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Accolade® and PrivateLine® are registered trademarks; BrightLink SoloTM , DuetTM , and SizeWiseTM are trademarks; and EPSON StoreSM and Extra CareSM are service marks of Epson America, Inc. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
linux-2.6.27 patches udhcp 0.9.8 uvc rev.219 wireless_tools 29 EPSON original drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/. GNU GENERAL PUBLIC LICENSE LICENSE Version 2, June 1991 Copyright ©) 1989, 1991 Free Software Foundation, Inc.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU LGPL This projector product includes the open source software programs which apply the GNU Lesser General Public License Version 2 or later version ("LGPL Programs").
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages—typically libraries—of the Free Software Foundation and other authors who decide to use it.
Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs.
"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6.
with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16.
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. libjpeg This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg". The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation. (2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent JPEG Group".
"The Graphics Interchange Format©) is the Copyright property of CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated." libpng This projector product includes the open source software program "libpng" which applies the terms and conditions provided by owner of the copyright to the "libpng". The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libpng programs libpng-1.2.
library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user. libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright ©) 1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors: Tom Lane Glenn Randers-Pehrson Willem van Schaik libpng versions 0.89, June 1996, through 0.
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions: 1. The origin of this source code must not be misrepresented. 2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source. 3. This Copyright notice may not be removed or altered from any source or altered source distribution. The Contributing Authors and Group 42, Inc.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions: 1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. 2.
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. 2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software. 3. This notice may not be removed or altered from any source distribution. L. Peter Deutsch ghost@aladdin.
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License. "Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity.
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work. 2. Grant of Copyright License.
Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License 5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions.
that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives. Copyright [yyyy][name of copyright owner] Licensed under the Apache License, Version 2.0 (the "License");you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.
A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any EPSON product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law.