PowerLite 1815p Multimedia Projector ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 10 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 10 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 12 Optional Accessories . . . .
2 Presenting with the Remote Control 3 Connecting to Computers, Cameras, and Other Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 . . . . . . . . 29 Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 30 Switching Between Picture Sources . . . . . . . . . . . . . . . . 30 Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 31 Stopping Action. . . . . . . . . . . . . .
4 Presenting Through a Wireless Network . . . . 55 Starting EasyMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Configuring Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Configuring the Connection. . . . . . . . . . . . . . . . . . . . . . . . . 58 Using Ad Hoc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Using Access Point Mode. . . . . . . . . . . . . . . . . . . . . . . . 65 Using Wireless Security Options. . . . . . . . . . . . . . . .
Presenting Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Controlling Your Scenario . . . . . . . . . . . . . . . . . . . . . . 117 Supported File Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 6 6 Fine-Tuning the Projector. . . . . . . . . . . . . . . . . . 119 Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Restoring the Default Settings . . . . . . . . . . . . . . . . . . . 121 Adjusting the Image . . . . . . . . . . . . . .
8 Maintaining the Projector . . . . . . . . . . . . . . . . . . 153 9 Solving Problems A Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . 154 Cleaning the Air Filter and Vent. . . . . . . . . . . . . . . . . . . . . 155 Replacing the Lamp and Air Filter . . . . . . . . . . . . . . . . . . . 156 Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . 159 Checking Lamp Usage . . .
B Projector Installation . . . . . . . . . . . . . . . . . . . . . . . 185 C Technical Specifications . . . . . . . . . . . . . . . . . . . . 187 D Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 193 FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 195 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Welcome The PowerLite ® 1815p is an easy-to-use projector that weighs less than 7 pounds. The projector offers up to 3500 lumens of brightness. You can connect it to a wide range of computers and video sources, or you can project from a USB storage device, or over an 802.11g, 802.11b, or 802.11a wireless network. Easy setup, control, and security: ■ 5-second startup time and Instant Off ® feature for fast setup and shut down ■ Automatic digital keystone correction ■ 1.
Using Your Documentation This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector. ■ Tips contain additional projection hints.
■ presentersonline.com Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Club—and it’s free.
Unpacking the Projector After unpacking the projector, make sure you have all these parts: PDF manual and registration CD-ROM EasyMP™ software CD-ROM Projector Wireless module and security screw Power cable Remote control and 2 AAA batteries USB cable VGA computer cable Carrying case Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location.
Optional Accessories To enhance your use of the projector, Epson provides the following optional accessories: Product Part number Replacement lamp V13H010L40 Air filter replacement set (2 filters) V13H134A08 Universal ceiling mount False ceiling plate Security bracket/cabling for gyro lock mounts Adjustable ceiling channel Suspension adapter ELPMBUNI ELPMBFCP ELPMBSEC ELPMBACC ELPMBAPL Kensington® security lock ELPSL01 50-inch portable screen (4:3 aspect ratio) 60-inch portable pop-up screen (4:3
Welcome
1 Displaying and Adjusting the Image W hether you’re presenting from a computer or video equipment, you need to follow some basic steps to display your image on the screen.
Positioning the Projector note You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 185 for details. If the projector isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.
Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be at about the level of the bottom of the screen. note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector. You can purchase this from Epson; see page 13.
Follow these steps to turn on the projector: 1. Open the A/V mute slide (lens cover). note You can set the projector to automatically turn off the projector lamp and enter “sleep mode” when it has not received any signals for 30 minutes. This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the P Power button. If you are done using the projector, unplug the power cord. To enable sleep mode, see page 132. 2.
3. Press the P Power button on the remote control or on top of the projector. The projector beeps once and the Power light flashes green as the projector warms up, then an image begins to appear. When the Power light stops flashing and remains green, the projector is ready for use. 4. If you are prompted to enter a password, see page 129. warning Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.
Shutting Down the Projector note Lamp life results will vary depending on mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. This projector incorporates Instant Off technology. To turn it off, you can press its P Power button as described below, unplug it, or turn off a power switch that supplies power to the projector. You don’t have to wait for the projector to cool off first. 1.
Troubleshooting Display Problems Follow these guidelines if you’re having trouble displaying an image. You Can’t Project an Image If you don’t see the image you are trying to project, try the following: ■ Make sure the cables are connected correctly, as described beginning on page 37. ■ Make sure the Power light is green and not flashing and the A/V mute slide (lens cover) is open.
■ If the function key doesn’t permit you to display simultaneously on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control Panel, open the Display utility. In the Display Properties dialog box, click the Settings tab, then click Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled.
Adjusting the Image Once you see your image, you need to make certain adjustments: ■ If the image is too high or too low, reposition it as described below. ■ To focus or zoom your image, see page 24. ■ If the image isn’t square, see page 24. ■ To quickly adjust the color, brightness, or contrast, see page 27. ■ To change the image aspect ratio, see page 28. ■ If you need to fine-tune the image and/or sound, see Chapter 6.
Focusing and Zooming the Image Turn the focus ring on the projector to sharpen the image. Turn the zoom ring on the projector to reduce or enlarge the image. Focus Zoom If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 32 for instructions.
You see a projected message: 2. Aim the projector so the message appears near the middle of the screen. Then use the zoom ring to enlarge the image so the white frame (not shown above) extends beyond the edges of the screen on all sides. 3. Press the Quick Setup button again. Two white boxes flash momentarily onto the screen, and the adjustment is complete. Your projected image now fits on the screen (some slight overlap is normal). The Quick Setup adjustment is retained when the projector is turned off.
You see this screen: 5. Use the pointer button on the remote control (or the arrow buttons on the projector) to select the corner you want to adjust, and press Enter. 6. Use the pointer button on the remote control (or the arrow buttons on the projector) to adjust the shape. 7. Repeat steps 5 and 6 as needed to adjust any remaining corners. 8. When done, press Menu to exit the menu system.
You can manually adjust the shape of the image to compensate for vertical and horizontal keystone distortion. First make sure the Keystone setting in the projector’s menu system is set to H-Keystone or V-Keystone: 1. Press the Menu button on the remote control (or on the projector’s control panel). note The projector’s arrow buttons may already be in Keystone correction mode if you haven’t used Quick Setup or Quick Corner. 2. Select the Settings menu and press Enter. 3.
Press the Color Mode button on the remote control, and then select from one of these options: ■ Presentation: For making color presentations in a bright room. ■ Text: For making black-and-white presentations in a bright room. ■ Theatre: For watching movies in a darkened room; gives images a natural tone. ■ Photo: For vivid, high-contrast still images in a bright room. ■ Sports: For vivid TV images projected in a bright room (video, S-video, or composite video only).
2 Presenting with the Remote Control T he projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 20 feet away. You can use the remote control to adjust the picture and sound (page 30) or as a pointer to highlight your presentation (page 33).
note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes. Using the Remote Control Make sure batteries are installed as described on page 160. Follow these tips for using the remote control: ■ Point the remote control at the front of the projector or at the screen. ■ Stand within 20 feet of the projector.
After you select a source, the screen goes dark for a moment before the image appears. Turning Off the Picture and Sound You can temporarily turn off the image and sound when you want to redirect your audience’s attention. There are two ways to do this: ■ Close the A/V mute slide, as shown below: ■ Press the A/V Mute button on the remote control. This turns the image black and stops the sound. To turn the image and sound back on, press the button again.
Stopping Action You can use the remote control to stop the action in your video or computer image. note This function pauses the image, not the sound. Because the source continues to transmit signals, when you resume the action, it won’t be at the point you stopped it. ■ To stop the action and keep the current image on the screen, press the Freeze button. The sound continues. ■ To restart it, press the Freeze button again.
Controlling the Volume To change the volume, press the control. or button on the remote note To temporarily shut off the sound and picture, press the A/V Mute button or close the A/V mute slide. You can also adjust the volume using the projector’s menu system. See page 126. Highlighting Your Presentation You can display a pointer to call out important information on the screen. If you want to customize the pointer tool, you can choose from three alternative shapes. Using the Pointer Tool 1.
3. When you’re done using the pointer, press Esc to clear the screen. Customizing the Pointer Tool You can change the appearance of the pointer by choosing from three alternative shapes. 1. Press the Menu button on the remote control, highlight the Settings menu, highlight Pointer Shape, and press Enter. You can select one of the pointer shapes shown at the left. 2. Select the shape you want and press Enter. 3. Highlight Return and press Enter. 4. Press Menu to exit from the menu system.
■ Use the pointer button to move the pointer on the screen. ■ Press the Enter button once to left-click, or press it twice to double-click. Press the Esc button to right-click. ■ To drag-and-drop, hold down the Enter button. Then use the pointer button to drag the object. When it’s where you want it, release the Enter button.
4. When done, press Menu to exit the menu system. Setting the Remote Control ID note If you’re using a remote control ID other than the default ID of zero, you have to set the ID each time you turn on the projector. The remote control’s default ID is zero. This lets you operate any projector. To set it to operate a specific projector, follow these steps: 1. Point the remote control at the projector you want to be able to operate. 2. Press and hold the ID button on the remote control. 3.
3 Connecting to Computers, Cameras, and Other Equipment T his chapter tells you how to connect the projector to a notebook or desktop computer, and/or to video equipment, such as a VCR, DVD player, or video camera. You can also connect the projector to a USB storage device or digital camera, use it with a CompactFlash® memory card, or connect it to your local area network.
Connecting to a Computer You can connect the projector to any computer that has a standard video output (monitor) port, including desktop models, PC notebook computers, MacBook, PowerBook, and iBook computers, and hand-held devices. You can also connect a Windows computer to the Type B USB port on the projector (see page 39). This allows you to connect an additional computer to the projector.
3. You can connect an optional stereo mini-jack audio cable to play sound through the projector (see page 48), or connect a USB cable to use the remote control as a mouse (see page 40). 4. When you’ve finished making any connections, see page 17 for instructions on turning on the projector and adjusting the image. Connecting to the USB Port You can connect a Windows XP or Windows 2000 (SP4) computer to the projector’s Type B (square) USB port and project your computer’s display. A USB 2.
6. Connect the flat end of the cable to any available USB port on your notebook or desktop computer. Messages appear as the projector is recognized and the software installation begins. 7. Follow the instructions on your computer screen to install the Epson USB Display software. If you see a “Digital Signature Warning,” select Continue. You will only need to install the software the first time you connect. After the software has installed, you see your computer’s desktop displayed by the projector.
The wireless mouse function is supported on systems with a USB port running Windows Vista,TM Windows XP, 98SE, Me, or 2000, or Mac OS X 10.2.x to 10.4.x. 1. Connect the square end of a USB cable to the projector’s USB port. USB cable 2. Connect the flat end of the cable to any available USB port on your notebook or desktop computer. 3. If necessary, configure your computer to work with an external USB mouse. See your computer documentation for details.
■ If your video player has a component video port (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a Component Video Source” on page 45. ■ If your video player has an RGB video port (either a single connector for a VGA-style monitor cable or three connectors labeled R/G/B), see “Connecting an RGB Video Source” on page 46. After connecting video cables, you may also want to connect an audio cable to play sound through the projector; see page 48.
Connecting a Composite Video Source 1. Locate an RCA-style video cable (one is usually provided with your video equipment or you can purchase one from an electronics dealer). 2. Connect the cable to the yellow video output connector on your player and the yellow Video connector on the projector: 3. If you want to play sound through the projector, see page 48 for instructions on connecting audio cables. 4.
Connecting an S-Video Source 1. Locate an S-video cable (one is usually provided with your video equipment or you can purchase one from Epson; see page 12). 2. Connect the cable to the S-video connector on your player and the S-Video connector on the projector: 3. If you want to play sound through the projector, see page 48 for instructions on connecting audio cables. 4. If you don’t need to make any other connections, see page 17 for instructions on turning on the projector and adjusting the image.
Connecting a Component Video Source You will need a special cable to connect your component video equipment to the HD15 (VGA-style) connector on the projector. You can order the HD15 to component cable (ELPKC19) from Epson; see page 13 for more information. 1. Locate an HD15 to component video cable or adapter. 2. Connect the cable to your player and the Computer 1 or Computer 2 connector on the projector. note Be sure your video player is not an RGB video source.
Connecting an RGB Video Source note Be sure your video player is not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation. 1. Locate the VGA computer cable provided with the projector. 2. Connect the cable to the video port on your player and the Computer1 or Computer2 port on the projector. 3. You may need to change the Computer1 Input or Computer2 Input setting in the projector’s Signal menu to RGB (see page 125). 4.
Connecting an External Monitor If you want to monitor your computer presentation close-up (on a monitor placed beside the projector) as well as on the screen, you can connect an external monitor. You can use it to check on your presentation even if you’ve pressed the A/V Mute button or switched to a different picture source. First make sure your computer’s VGA cable is connected to the projector’s Computer1 port (see page 38).
Playing Sound Through the Projector You can play sound through the projector’s speaker system or attach an external speaker system. To play sound through the projector, follow these steps: 1. Locate the appropriate cable and connect it to the Audio jack on the projector. ■ If you have equipment connected to the Computer 1 or Computer 2 port, use a stereo mini-jack cable. Connect the cable to the Audio1 port (for Computer1) or the Audio2 port (for Computer2).
Connecting External Speakers You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projector’s built-in speaker system is disabled. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter. 2.
Connecting to a Digital Camera or Other Device note Use a cable less than 10 feet long and connect the camera directly to the projector. Your projector may not function correctly if you use a longer cable or connect your camera to a USB hub. You can connect your digital camera, USB flash memory drive, USB hard drive, or multimedia storage viewer, such as the Epson P-5000 or Apple iPod.® Use the USB cable specified for your device.
Inserting a CompactFlash Card You can use a CompactFlash card to store images, movies, and Scenario files. This lets you project your files without connecting to a laptop or PC. To place your files on the card, copy them from your computer to the card using a card reader. If the projector is connected to your local area network, you can also send the files to the card over the network (see page 151). note The memory card slot also accepts MicrodriveTM cards.
Inserting the Wireless 802.11g/b/a Module caution Use only the Epson 802.11g/b/a wireless module in the projector. To use the projector over a wireless network, you need to install the projector’s wireless LAN module (included). Once the module is installed, see page 55 to configure the projector and your network. 1. Insert the wireless LAN module that came with your projector. caution Never remove the module while its indicator light is green or when projecting wirelessly.
Connecting a Network Cable To connect the projector to your local area network (LAN), use a commercially available 100baseTX or 10baseT network cable. To ensure proper data transmission, use a Category 5 shielded cable or better.
Connecting to Computers, Cameras, and Other Equipment
4l Presenting Through a Wireless Network T his chapter tells you how to send pictures to the projector through a wireless network. Using EMP NS Connection, you can project images shown on your computer screen—including text, graphics, and video—directly to your audience.
Starting EasyMP note Use only the Epson 802.11a/b/g wireless module in the projector. If you see a message asking you to insert a LAN or memory card, check to make sure your 802.11 a/b/g module is properly inserted (see page 52). Before connecting to the projector, you have to switch it to EasyMP mode. Follow these steps: 1. Point the remote control at the projector and press the P Power button. 2. Press the EasyMP button on the remote control to select EasyMP as the source. You see this screen.
Configuring Basic Settings You can give your projector a unique name, enable a projector keyword, or create a password for controlling the projector using your computer’s Web browser. 1. Press the Menu button, then choose Network and press Enter. 2. Choose Network Configuration and press Enter. 3. Choose Basic and press Enter. You see the following screen: 4. Make sure the projector has a unique name, so you can identify it when connecting to it from your computer.
5. Press the pointer button to select individual letters; then press Enter to input a character. To add a blank space or to navigate backward and forward through the input text, highlight the arrows and press Enter. To toggle symbol settings or capital letters, highlight the option and press Enter. When you’re done, highlight Finish and press Enter. 6.
connect to the projector in this mode, your connection to other wireless networks or devices is broken; you can connect to the projector only. ■ Access Point mode (infrastructure mode) lets multiple computers access the projector at the same time and easily trade off control over the projector. To use Access Point mode, you need a wireless (802.11a, 802.11b, or 802.11g) access point or an AirPort Extreme (or AirPort) base station, and one or more computers with wireless network cards or adapters.
4. Make sure Quick is selected for the Connection mode. If not, use the pointer button on the remote control to highlight Quick, then press Enter to select it. 5. If your network is using 802.11a, use the pointer button on the remote control to highlight 802.11a, then press Enter to select it. 6.
Configuring the Network Settings for Windows Before connecting to the projector, you need to make sure the settings for your notebook’s or PC’s network card match the settings you entered for the projector. 1. Access your wireless network Properties window. For example, in Windows XP you would click Start > Control Panel > Network and Internet Connections. Then click the Network Connections icon.
2. Right-click the Wireless Network Connection icon and select Properties. You see a screen similar to this: Click here 3. Click the Configure button. 4. Click the Advanced tab.
5. Check your wireless card or adapter device settings. (Depending on the type of card or adapter you’re using, some of the settings may be different than those listed here.) ■ Set the Network Type to 802.11 Ad Hoc. ■ Set the SSID to match the name you assigned to the projector’s ESSID. ■ Make sure Encryption is Disabled. 6. Click the General tab and make sure that your wireless card or adapter is enabled. 7. When you’re done, click OK to close the Properties dialog box.
3. Make sure Location is set to Automatic. Select Automatic note: If you don’t need the other network port configurations, disable them by deselecting their checkboxes. When you connect in Ad Hoc mode, your connection to other wireless networks or devices is broken. If you need to remain connected to your wireless network, use Access Point mode, as described on page 65. Also, make sure you reconnect to your original wireless network when you are done using the projector.
Using Access Point Mode To use Access Point (infrastructure) mode, first adjust your projector and wireless access point or AirPort base station settings as described in this section. Configuring the Projector 1. Press the Menu button, then choose Network and press Enter. 2. Choose Network Configuration and press Enter. 3. Choose Wireless LAN and press Enter. You see this screen: 4. Make sure Advanced is selected for the Connection mode.
network may be different from that of your AirPort base station; select your base station in the AirPort Admin utility and click Configure to check the name of your network.) Highlight the ESSID text box, press Enter, and enter a name: Press the pointer button to select individual letters; then press Enter to input a character. To add a blank space or to navigate backward and forward through the input text, highlight the arrows and press Enter.
Now you’re ready to set up your computer for wireless projecting. Go to “Configuring the Network Settings for Windows” below, or go to “Setting Up Your Mac for Access Point Mode” on page 73. If you want to enable security options for your network, see page 75 to set up the option that your network uses on the projector.
You see a screen similar to this: Click here 3. Click the Configure button. 4. Click the Advanced tab.
5. Check your wireless card’s or adapter’s device settings. (Depending on the type of card or adapter you’re using, some of the settings may be different than those listed here.) ■ Set the Network Type to Infrastructure. ■ Set the SSID to match the name assigned to the access point (which should also match the projector’s ESSID). ■ Make sure Encryption is Disabled if you have not set up encryption on the projector. 6. Click the General tab and make sure that your wireless card or adapter is enabled.
9. Select Internet Protocol and click the Properties button. You see this screen: note For specific details about your network, please consult your network administrator. 10. If your access point uses DHCP, select Obtain an IP address automatically. Otherwise select Use the following IP address and Use the following DNS server addresses, then enter the required information: ■ IP address: Type in the IP address you want to assign to the computer. It must be formatted like other addresses on the network.
settings; then follow any instructions on the screen to enable the device.) You see a screen like this: 13. Verify that you’ve enabled your computer’s connection to the access point. It should be listed with the small icon next to it, indicating a connection. If it’s not listed, click Configure and type the name of your access point. 14. When you’re done making settings, click OK to close the dialog box. Now you’re ready to connect to the projector. See “Projecting Over a Network” on page 81.
note If you cannot identify the gateway address using this Windows utility, use the administrator’s utility software that came with your access point. Checking the Gateway IP Address on Windows If you’re entering IP addresses manually and need to find out the gateway IP address (the IP address of your access point), make sure the wireless connection to the access point is currently active, as described in the previous section. Then follow these steps: 1. Access your wireless network Properties window.
3. Click the Support tab. The gateway’s IP address is listed as shown: Gateway address Setting Up Your Mac for Access Point Mode Your AirPort software is automatically configured to allow your Mac to detect Access Point networks. Typically, you only need to select your AirPort network name from the AirPort status menu on the Mac menu bar. If you’re having problems connecting to the projector, follow these steps: 1. From the Apple pull-down menu, select System Preferences. 2. Click the Network icon.
3. Make sure Location is set to Automatic. note If you don’t need the other network ports, disable them by deselecting their checkboxes. If more than one network port is enabled, the projector software warns you to turn off AirPort when you first connect the projector. Disregard this message. Your AirPort network and base station names may be different. To check or change your AirPort network name, start the AirPort Admin utility, select your base station, and click Configure.
10. Click the AirPort icon on the menu bar at the top of the Macintosh desktop. You see the AirPort status menu: 11. Check to make sure AirPort is turned on. 12. Select the name of your AirPort network. Using Wireless Security Options You can use the following security options when connecting to the projector wirelessly: WEP encryption, WPA security, EAP-TLS certificate validation, or LEAP, EAP, or PEAP authentication.
You see the following screen: 4. Press Enter to show the menu, then highlight WEP and press Enter. 5. For the WEP encryption setting, highlight 128Bit or 64Bit and press Enter. 6. For Format, highlight HEX to enable hexadecimal input or ASCII to enable text input, then press Enter. note Text input for WEP encryption varies with different access points; check with your network administrator. Try ASCII first. If that doesn’t work, try Text2 and then Text3. 76 7.
option and press Enter. When you’re done, highlight Finish and press Enter. 8. Check with your network administrator for directions on entering a key for your network, and follow these general guidelines: ■ For 128 bit WEP encryption with hexadecimal input, enter 26 characters, from 0 to 9 and from A to F. ■ For 64 bit WEP encryption with hexadecimal input, enter 10 characters, from 0 to 9 and from A to F. ■ For 128 bit WEP encryption with ASCII or text input, enter 13 alphanumeric characters.
You see the following screen: 4. Press Enter to show the menu, then choose WPA-PSK(TKIP) or WPA-PSK(AES) and press Enter. Highlight the PSK (pre-shared key) text box and press Enter. Press the pointer button to select individual letters; then press Enter to input a character. To add a blank space or to navigate backward and forward through the input text, highlight the arrows and press Enter. To toggle symbol settings or capital letters, highlight the option and press Enter.
Enabling EAP, LEAP, or PEAP Authentication 1. Press Menu. Highlight Network and then press Enter. 2. Choose Network Configuration and press Enter. 3. Highlight Security, then press Enter. You see the following screen: 4. Press Enter to show the menu, then choose EAP-TTLS/MD5, EAP-TTLS/MS-CHAPv2, LEAP, PEAP/MS-CHAPv2, or EAP-FAST/GTC and press Enter. 5.
Highlight the User name text box and press Enter. Press the pointer button to select individual letters; then press Enter to input a character. To add a blank space or to navigate backward and forward through the input text, highlight the arrows and press Enter. To toggle symbol settings or capital letters, highlight the option and press Enter. When you’re done, highlight Finish and press Enter. ■ Highlight the Password text box and press Enter. Enter the password as you entered the User name. 6.
You see the following screen: 4. Press Enter to show the menu, then choose EAP-TLS and press Enter. The certificate information appears on the screen. 5. When you’re done making these settings, select Return, select Setup complete, and then select Yes to confirm that you want to save the changes. Press Menu to exit the menu system.
note If you don’t see your network adapter’s IP address, allow a minute for it to appear. If your access point or AirPort base station uses DHCP (Distribute IP addresses setting is enabled for AirPort), sometimes it takes a minute for the server to pick up the IP address. Once you’ve selected the IP address for your network adapter, you won’t see the Switch network dialog box when you start NS Connection.
If the connection is working properly, you see your projector listed. If you have additional Epson projectors on the network, they are also listed, along with their status. The status is indicated next to each projector’s name. 5. Once the name of your projector appears, select it and click Connect. If more than one projector is listed, you can select additional ones and connect to them (up to four) at the same time.
8. If necessary, you can drag the control bar out of the way on your screen. 9. When you’re done with your presentation, click Disconnect on the control bar. Solving Connection Problems If you don’t see your projector, check the following: 1. Make sure your wireless signal is strong enough to establish a connection. If you have a Mac, check the AirPort icon on the Mac menu bar. For Windows, see the documentation for your access point or wireless network card or adapter.
7. If you still don’t see your projector, follow the instructions in “Connecting in Advanced Connection Mode” on page 86 to connect to the projector. Using the Control Bar From the control bar, you can access these NS Connection features: Displays the Select target projector dialog box. Stops projection of computer images while connecting to the projector. The projector projects the computer image. Pauses projection of computer images. Click again to restart projection.
Connecting in Advanced Connection Mode 1. Click Manual search on the NS Connection screen. 2. Enter the IP address or the projector name for the projector you want to connect to, and click OK. The Projector is added to the EMP NS Connection screen. If the search fails to find a projector with the specified IP address, the searching icon turns into a question mark. If this happens, run EasyMP on your projector (see page 56) to check the projector’s IP address, then repeat this step. 3.
4. If you are prompted for a keyword, enter the four-digit number displayed on the EasyMP Network screen and click OK. The computer’s image is transmitted to the projector and appears on the screen. See page 83 for details about using the floating control bar on your computer desktop. Enabling Network Security The projector includes the following network security options which you can enable for network projection: ■ Data encryption Encode and transmit data.
Enabling Data Encryption 1. Click Set options on the main screen. 2. Click the General Settings tab. 3. Select the Encrypt communications checkbox. 4. Click OK.
Enabling Network Security Options You need to enable network security including WEP, WPA, EAP, LEAP, or PEAP, or firewall settings on your network and on the projector (see page 75). For network setting details, follow the directions from your network administrator. If using EAP, you need to make settings at the projector that match the authentication server settings. Check with your network administrator for details on RADIUS settings.
Multi-screen Projection note For a Mac, you have to connect a monitor to the computer and use the multi-screen display function. For Windows, even if a monitor is not connected, you can set a virtual display by installing the virtual display driver in EMP NS Connection. See page 182. When using Multi-screen display, you can set each projector to display a section of the screen or image, to create a single image spanning a large area. Make sure the projectors are at least 3.
2. Click Display properties. 3. Drag the monitor icons to arrange the positions of the displays. 4. Close the Display Preferences (Windows) or System Preferences (Macintosh), when you are done arranging the display numbers.
5. To allocate projectors to each display, choose a number from the menu under Display. 6. Click the Connect button when you are ready to project the image. 7. You can use the Screen Preview button on the NS Connection toolbar to check the image on each screen. Projecting Video Clips note Only MPEG1-Layer2 audio is supported. The maximum supported MPEG2 video resolution is 720 × 480 NTSC or 720 × 756 PAL (without audio).
3. Click the Select file button. Locate the MPEG2 video you want to project and click Open. 4. Use the standard playback buttons on the screen to start, pause, rewind, and control other video functions. 5. When you’re finished projecting video, click the Close button on the screen. note The video will be projected on the screen, but will not appear on the host computer.
Using Presentation Mode note If you want to display an image or logo instead of a black screen, you can replace the image.jpg file in the EMP NS Connection V2 \Image folder. In windows, this is located in C:\Program Files \Epson Projector \EMP NS Connection V2\image. In MAC OS X, it is located in \Applications\EMP NS Connection V2\Image. Disconnect and then reconnect to the projector after you replace the image.
3. Click Use multi-display, then click Display properties. 4. On the Display Properties screen in Windows, make sure your Epson Projector Virtual Display Driver is selected, then check Extend my Windows desktop onto this monitor and click OK. In the Mac OS X Displays program, select the Arrangement tab and uncheck the Mirror Displays setting to deselect it.
5. Set your projector to Display 2 (or the Virtual Display Driver you selected in step 4) in NS Connection, then click Connect. 6. Open your presentation in PowerPoint or Keynote. 7. In Keynote, select Preferences.
In PowerPoint, open the Slide Show pull-down menu and select Set Up Show. 8. In Keynote, set the Presentation Mode to Present on secondary display. In PowerPoint, set the Multiple monitors box to Display slide show on Monitor 2 (or the monitor associated with your Epson Virtual Display) and check Show Presenter View. Then click OK. 9. Start your slideshow. The projector displays the slides, and your laptop displays your notes and controls.
Presenting Through a Wireless Network
5 Presenting from a USB Drive, Camera, or CompactFlash Card T he projector’s EasyMP PC Free feature lets you give presentations from a USB flash drive, digital camera, USB multicard reader, or CompactFlash card. You can play movies, display graphics, or play a scenario, a format that lets you create your own slideshow using PowerPoint files, image files, and MPEG videos. When a CompactFlash card is inserted and the projector is on a network, you can also transfer files to the card over the network.
Presenting Files From a USB Drive or CompactFlash Card This section explains how to project individual image or movie files from a USB hard drive, flash memory drive, or CompactFlash card using EasyMP. See page 118 for a list of the supported file formats. Follow these steps to display images or play movies: 1. Connect your external drive or insert your CompactFlash memory card (see page 50). If you are using an external hard drive, plug in its power cord. 2. Turn on the projector, if it is not already on.
5. Select Open Folder. You see your image files when the folder opens. 6. Position the cursor on the movie or image file you want to project and press Enter. 7. Select View Image or Play Movie. If you selected an image, it is projected on the screen. If you want, you can press a side of the pointer button to rotate the image while you’re viewing it. note If you exit the PC Free mode on the projector, disconnect and re-connect your USB device before starting again.
7. Position the cursor on the folder and press Enter. note Make sure your camera shows up on your desktop as a drive letter. If it does, it is probably a USB mounted device and will work with the projector software. The EasyMP software does not support TWAIN-compliant digital cameras. 8. Select Open Folder. You see your image files when the folder opens. 9. Position the cursor on the image file you want to project and press Enter. 10. Select View Image. The image is projected on the screen.
You see your files displayed on the screen: 4. Use the pointer button on the remote control to highlight the folder containing your images and press Enter. 5. From the pop-up menu, use the pointer to select Play Slideshow and press Enter. (Or highlight the Slideshow button at the bottom of the screen and press Enter.) The images contained in the folder are presented as a slideshow. Use the remote control to run the slideshow as described in the next section.
Changing Timing and Other Settings For each folder on the USB drive or memory card, you can set the display timing for your slides and change several other display settings. 1. Select the folder containing the images for the slideshow settings you want to change and press Enter. note You can also display the Option screen by selecting Option at the bottom of the PC Free screen and pressing Enter. 2. From the drop-down menu, use the pointer to select Option and press Enter. You see this screen: 3.
■ Display order Lets you choose between displaying alphabetically by file name or by image file date. ■ Continuous Play Determines whether to repeat the display of images in the folder. ■ Screen switching time Sets the display time for each image. Choose No if you want to change slides manually. ■ Effect Lets you choose from various transitions between slides, such as Dissolve or Wipe. 4. When you’re done, highlight OK and press Enter.
Converting a PowerPoint File to a Scenario Follow these steps to convert a PowerPoint file to a scenario. Once the scenario is created, you can set up transitions as described on page 111. 1. Make sure the EMP SlideMaker program is closed. 2. Locate the PowerPoint file you want to use in My Computer or Windows Explorer. 3. Drag the file icon on top of the your desktop. EMP SlideMaker2 icon on 4. When you see a message about file conversion, click Continue. 5. When you see the next message, click Start.
Creating a Scenario from Scratch Use this method when you want to create a scenario from a selection of PowerPoint slides, graphics, or movie files. You’ll need to set up your scenario file and folder, build the scenario, set up transitions, and check the scenario. Setting Up the Scenario File and Folder 1. Double-click the EMP SlideMaker2 icon on your computer’s desktop (or click Start > Programs or All Programs > Epson Projector > EMP SlideMaker2).
■ Click Configure BGM(W) to play an audio file during the scenario. A selection screen appears letting you choose a .WAV file. After you select the file you want, click the arrow button to the right of the option to play it. ■ The Background Color appears around images that don’t fill the entire screen area. Select a new color, if desired. ■ Select the Image Quality for imported PowerPoint slides. Higher-quality images look better on the screen but may take longer to appear. 3. Click OK.
Follow these steps: 1. Use the navigation tools on the left side of the EMP SlideMaker 2 screen to locate the files you want to include in your scenario. PowerPoint, JPEG, bitmap, and movie files appear as icons in the file window. Click to see preview Thumbnail preview 2. Click the icon for each file that you want to preview. The preview appears in the thumbnail preview window. If you click a PowerPoint icon, thumbnail images are generated for all the slides in the PowerPoint file.
3. Drag and drop the files you want to include in your scenario from either the file window or thumbnail window into the scenario window. (You can also double-click a thumbnail to add the file to the scenario.) Scenario Cell Check a slide’s animation effects here note Transition effects created in PowerPoint look smoother than those you add with EMP SlideMaker 2. To include a whole PowerPoint file (instead of individual slides), drag the PowerPoint icon itself into the scenario window.
6. When you’re done, click the Save button or choose Save from the File menu. Then see page 114 to transfer the scenario to your USB drive or CompactFlash card. Setting Up Transitions EMP SlideMaker 2 lets you set your slides to advance manually or automatically after a specified period of time. You can also choose from a variety of transition effects between slides. 1. Click the cell or cells for which you want to set up in the scenario window.
3. Click Cell Properties. You see this dialog box: Click to change slides manually Click to change slides automatically Select transition effects 4. Choose how you want to advance to the next cell. note Transition effects look smoother when you create them in the PowerPoint file itself and use that file to create a scenario. ■ If you want to change slides manually using the remote control, select On mouse click.
Checking Your Scenario You can play your scenario before you transfer it to a USB drive to make sure it looks and sounds the way you want it to. 1. Use the navigation tools in the folders window to locate the scenario file you want to review. Click the file, then select File > Open to open the scenario. 2. Click Scenario Option(s) > Scenario Preview. The Scenario Preview window displays. If the scenario is set to advance automatically (see page 112), it begins to play.
Transferring Your Scenario to a USB Drive or CompactFlash Card note Don’t use Windows to copy the scenario to your USB drive or memory card, or it may not play properly. You must connect the USB drive (or card reader) before you select Send Scenario from the Scenario Option(s) menu. If you don’t, you won’t be able to see the drive in the drive selection window. If this happens, close and restart EMP SlideMaker 2. Once your scenario is saved, you can transfer it to a USB drive or CompactFlash memory card.
The autorun setting means that the scenario will start playing whenever the projector is turned on (with the drive connected to the projector). 7. Do one of the following: ■ If you don’t want the scenario to run automatically, click Cancel. Skip to step 11 to remove the drive and insert it in the projector. ■ If you want it to run automatically, click OK and continue with the following instructions. You see the Edit Autorun window: 8.
Presenting Scenarios Before you begin, connect the USB drive (see page 50) or insert the CompactFlash card containing the scenario to your projector (see page 51). The follow these steps to present your scenario: 1. Turn on the projector, if it’s not already on. ■ If your scenario is set to autorun, it will start as soon as the projector warms up. ■ If your scenario is not set to autorun, you need to start it manually. Continue with the following steps. 2.
Controlling Your Scenario While your scenario is running, use the remote control as follows: ■ Press Enter or Page down to display the next animation, slide, or image, or to begin playing a movie. ■ Press Page up to display the previous slide or image, or to replay a movie. note ■ Press the appropriate side of the slide or image on the screen. ■ To exit the scenario at any point, press the Esc button. Select Exit and press the Enter button.
Supported File Formats The following file types may be projected from a digital camera, external hard drive, flash memory drive, or CompactFlash card: File Type Extension Notes Scenario .sit These are scenario files created using the EMP SlideMaker 2 program that is included with the projector. Graphics .bmp Images with a resolution greater than 1024 × 768 cannot be projected. .gif Images with a resolution greater than 1024 × 768 cannot be projected. .
6 Fine-Tuning the Projector Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options Menu list The menus are listed on the left and the options available for the highlighted menu are shown on the right. 2.
4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the Enter button to view a sub-screen for changing the setting. ■ Press the left or right side of the a slider bar. pointer button to adjust ■ To select from two or more settings, use the pointer button to highlight the desired setting and press Enter. 5.
Adjusting the Image You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast. 1. Press the Menu button on the projector or remote control and select the Image menu. You see the Image menu screen. 2. Use the pointer button to highlight the desired option, then adjust it as needed: note The available settings vary depending on the input source selected. ■ Color Mode Lets you quickly adjust the color and brightness for various environments.
sRGB: For matching the color palette of standard sRGB computer displays. Blackboard: For projecting accurate colors on a green chalkboard (adjusts the white point). note Customized: For manual color adjustment (see below). ■ The Brightness setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness. Select Brightness Control in the Settings menu, then choose High or Low (the default setting is High). Brightness Lightens or darkens the overall image.
2. Press the Enter button to select Customized, then press Esc to return to the Image menu. 3. Select Color Adjustment and press Enter. You see hue and saturation controls on the screen for six colors: RGBCMY (red, green, blue, cyan, magenta, and yellow). 4. Select the color axis you want to adjust and press Enter. You see color controls for hue and saturation. Hue changes the balance of color, and saturation changes the strength of the color. 5. Use the pointer button to adjust the hue and saturation.
2. Use the pointer button to highlight the desired option, then adjust it as needed: ■ Auto Setup Leave this setting On to automatically optimize computer images. Turn it off if you want to save adjustments you have made to the Tracking, Sync, and Position settings. ■ Tracking Adjust this value to eliminate vertical stripes in computer images. ■ Sync Adjust this value if computer images appear blurry or flicker.
Customizing Projector Features You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features. ■ Keystone Adjusts the shape of the image if the projector has been tilted upward or placed at an angle to the screen. Select H/V-Keystone to correct horizontal and vertical keystone distortion, or to turn Auto V-Keystone on or off (see page 26). Select Quick Corner to adjust the shape and position of the projected image (see page 25).
■ Remote Receiver Deactivates the projector’s front and/or back sensors that detect signals from the remote control. Use this setting to prevent use of the remote control or to stop interference from bright fluorescent lights. ■ Test Pattern Displays a test pattern for use when adjusting the zoom and focus, and when performing keystone correction.
You see this screen: 2. Use the Hold down pointer button to select Password and press Enter. 3. When you see a message asking if you want to change the password, select Yes and press Enter. 4. Hold down the Num button on the remote control and use the numeric keypad to enter a four digit password. (The default setting is 0000.) 5. When you see a confirmation message, reenter the password. Then press the Menu button to exit the screen.
Starting the Projector with a Password When the password function is enabled, you see this screen when you plug in and turn on the projector: note If you leave the projector plugged in, the Password Protect Release screen will not appear. It appears only if you unplug and reconnect the power cable. 5GG [QWT FQEWOGPVCVKQP HQT OQTG KPHQTOCVKQP Hold down Hold down the Num button on the remote control and use the numeric keypad to enter the four digit password.
Capturing the Image Start by displaying the image you want to use from either a computer or video source, such as a DVD player or digital camera. Then follow these steps to capture the image and transfer it to the projector: note When you choose an image for the user’s logo, it erases any previously used image. You can save an image up to 300 × 400 pixels in size. 1. Press the Menu button on the remote control, highlight the Extended menu, and press Enter. 2. Highlight User’s Logo and press Enter. 3.
Choosing When to Display the Image After your image is saved, you can set it to display as the startup screen, the screen you see when there’s no signal, or the screen you see when you press the A/V Mute button (see page 31). 1. Press the Menu button, highlight the Extended menu, and press Enter. 2. Select Display and press Enter. 3. Choose from these display options: note ■ Set Display Background to Logo to display your image when there is no signal.
Customizing Power and Operation You can use the Extended menu to customize the way the projector displays images, enable quick startup, turn sleep mode on or off, and customize other projector operations. ■ Display Use this setting to turn off the display of messages, change the background color, enable logo display, or turn off the startup screen display. ■ User’s Logo Create a custom startup screen, as described on page 129.
minutes or when the A/V mute slide (lens cover) is closed. Enable High Altitude Mode when you are using the projector above 4900 ft (1500 m). ■ Standby Mode Select Network On to enable the projector to be monitored over a network when it is in standby mode (the power light is orange). ■ USB Type B Select Easy MP to project your computer’s display through the projector’s Type B USB port (see page 39).
Multi-screen Color Adjustment You can match the color of projected images when two or more projectors are being used to display images near each other, or when you use the multi-screen feature to project from one source (one image) as described on page 90. For each screen, you can set five levels of brightness and color correction. note If you use two or more projectors side-by-side, exhaust from adjacent projectors might cause overheating. Leave at least 2 feet (60 cm) of space between projectors. 1.
7 Managing Projectors T he software included with your projector lets you monitor and control your projectors from a remote computer: ■ Use EMP Monitor (available for Windows only) to see your projectors’ status, switch image sources, and control basic settings. ■ Use the mail notification function to receive e-mail alerts about possible problems. You can also use NS Connection to register up to 16 projectors as a group.
Connecting to a Wired Network Follow these steps to connect the projector to your network and configure it with an IP address. 1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the LAN port on the projector. See page 53. 2. Point the remote control at the projector and press the P Power button. 3. Press the EasyMP button on the remote control to select EasyMP as the source. 4.
■ If your network does not assign addresses automatically, turn off DHCP and enter the projector’s IP Address, Subnet Mask, Gateway Address, and DNS Servers, as needed. To enter numbers, use the pointer button on the remote control to highlight the number you want to input, then press the Enter button. 8. When you’re done making all necessary changes, select Return, select Setup complete, and then select Yes to confirm that you want to save the changes. Press Menu to exit the menu system.
4. Highlight On to receive email notifications, then press Enter. 5. Enter the IP address for the SMTP server for the projector. note If a critical problem develops with a projector which causes it to suddenly stop working, it may not be possible for the projector to send a message. If Standby Mode is set to Network On in the Extended menu, the projector can still be monitored even if the projector is in standby mode (when the power is off).
Using EMP Monitor EMP Monitor lets you use a remote computer to manage your projectors, whether connected wirelessly or over a wired network. It lets you easily turn the projectors on or off (together or individually), switch image sources, and check their status. Before using EMP Monitor, make sure you’ve installed the software (available for Windows only) as described on page 182. The computer you’re using to monitor the projector should already be connected to your network.
Registering a Projector Before you can monitor a projector, you have to register it. Follow these steps to automatically search for your projector(s). 1. Open EMP Monitor as described above. You see this screen: 2. Select Edit > New > Projector (automatic search).
3. Click Search to locate projectors currently operating on the network. Any projectors found on the network are listed as shown below: note If the projector is not automatically found, your projector may not be connected or configured correctly for the network. See page 58. 4. Select the projector you want to add by clicking its name, then click the Edit button.
5. Enter a Display name, select a Parent group, if necessary, enter a Monitor Password, if necessary, and a Description for the projector. Then click the Register button. To register additional projectors with EMP Monitor, repeat steps 2 through 5. 6. When you’re done adding projectors, click Cancel. note You see a screen with a list of all registered projectors: To delete a projector from the list, right-click the projector name, and click Delete.
The following tables describe the status icons shown on the EMP Monitor screen. Group status icons No warnings or problems. All projectors in the group are operating normally. Warning or problem. A projector in the group has a warning or problem. Monitoring disabled. Right click the icon and select Monitoring Enabled to begin monitoring the group. Data is currently being updated. Type status icons No warnings or problems. Warning or problem. Monitor Password error.
Power status icons The projector is powered on and its status is normal. The projector is powered off and its status is normal. The projector is powered on and its status is abnormal. The projector is powered off and its status is abnormal. Temperature level status icons The projector’s internal temperature is normal (low). The projector’s internal temperature is normal (medium). The projector’s internal temperature is normal (high). The projector’s internal temperature is high (high-temperature warning).
Error status icons (continued) Air flow sensor error. There is a problem with the projector’s air flow sensor; contact Epson as described on page 178. Lamp cover door open. Close the lamp cover door. Lamp out. The lamp has reached the end of its life. Lamp failure at power on. The lamp has reached its end of life or is installed incorrectly. High internal temperature error. The projector is turned off automatically. Internal (system) error. Contact Epson as described on page 178. Fan error.
Controlling Your Projectors note To turn on a projector when it’s in standby mode (plugged in but not projecting), you must have selected Network On as the Standby Mode setting in the projector’s menu system (see page 133). The control buttons in the upper-right let you turn the projector on and off and select video sources. (Hold the mouse pointer over a button to see a description of its meaning.
Configuring the Monitoring Interval If you need to have the most current status information about your projectors, click the Refresh button in EMP Monitor. To select how often EMP Monitor checks the status of projectors, follow the steps below: 1. From the Tool menu, select Environment Setup. You see this screen. note If you want EMP Monitor to run whenever you start your computer, click Register at startup. 2. Enter the desired Update interval and click OK.
You see this screen: 3. Turn the Mail notification function setting On. 4. Enter the IP address and port number of your network’s SMTP (outgoing) mail server. 5. Enter the Sender (projector) mail address. 6. Enter up to three e-mail addresses to send alerts to in the Recipient mail address boxes. 7. Click the Notification event buttons to select the conditions under which an e-mail alert will be sent. 8. When you’re done, click the OK button to close the Set mail notification function window.
When the problem has been fixed, EMP Monitor sends a message indicating the problem has been resolved. Using a Browser to Monitor the Projector If your projector is connected to a network, you can use a standard web browser to monitor and control it. 1. Make sure that the projector is set up for your network, as described on page 58. (Standby Mode in the Extended menu should be set to Network On to monitor the projector in standby mode.
■ If you set a Web control password in the projector’s Network menu, enter it in the Password box, then click OK. You see this screen: Menus Functions corresponding to remote control buttons 4. Select one of the menu options listed on the left, then change any of the settings as needed. These settings correspond to those found in the projector’s menu system.
Transferring Files by FTP If your projector is connected to a network as described on page 136, you can send files over the network to a CompactFlash card inserted in the projector (see page 51). Then you can use the projector’s PC Free feature to present images and movies (see page 100). You can use any FTP client software to send files to the projector. For example, you can connect to the projector using the Finder on a Macintosh.
Managing Projectors
8 Maintaining the Projector Y our projector needs little maintenance. All you have to do is keep the lens clean. You may also need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. Use a canister of compressed air to remove dust. To remove dirt or smears on the lens, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens. Cleaning the Projector Case caution Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case. 154 Before you clean the case, turn off the projector and unplug the power cord.
Cleaning the Air Filter and Vent Your projector includes an air filter to ensure the best performance. If dust collects on the air filter (on the bottom of the projector) or vent (on the front of the projector), clean them as described below. Dust clogs prevent proper ventilation and can cause overheating and damage the projector. Follow these steps: note To order replacement air filters, request part number V13H134A08. See page 13 for ordering information. 1.
Replacing the Lamp and Air Filter note When you get a replacement lamp for your projector, you should replace the filter. Turn off this product when not in use to prolong the life of the projector. The life span of the projection lamp is about 2500 hours if Brightness Control in the Settings menu is set to High (default), and 3000 hours if Brightness Control is set to Low. See page 159 to check the lamp usage.
Follow these steps to replace the lamp and air filter: warning 1. Turn off the projector and unplug the power cord. 2. Let the projector cool for at least an hour (if it has been on). The lamp is extremely hot immediately after use. 3. Loosen the lamp cover screw (you don’t need to remove it). Then slide the lamp cover to the side and lift it off of the projector. 4. Loosen the two screws holding the lamp in place (you can’t remove them). Let the lamp cool fully before replacing it.
5. Hold the lamp as shown and pull it straight out. note The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.) 7. Once the lamp is fully inserted, tighten its screws. 8. Replace the lamp cover, then tighten its screw. 9. Slide out the air filter on the bottom of the projector and remove it. 10.
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menus. 1. Press the Menu button on the remote control or on the projector’s control panel. You see the main menu. 2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight Reset, then press Enter. You see this screen: 3. Select Reset Lamp Hours and press Enter. 4. When you see the prompt, select Yes and press Enter. 5.
The life span of the lamp is about 2500 hours if the Brightness Control setting in the Settings menu is set to High (default), and 3000 hours if the Brightness Control setting is set to Low. Make sure you have a spare lamp handy if the usage hours on this menu are close to the life span of your lamp. Replacing the Batteries caution Replace the batteries in the remote control as described below: When replacing batteries, take the following precautions: 1. Turn the remote control over.
Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent damage: note ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector. ■ When transporting the projector a long distance, first place it in a hard-shell shipping case, then pack it in a firm box with cushioning around the case.
Maintaining the Projector
9 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on top of the projector or on the remote control. 1. Press the ? Help button on the remote control or on the projector. You see the Help menu: 2. Use the pointer button on the remote control or the navigational buttons on the projector to highlight menu items. 3. Press the Enter button on the remote control or on the projector to select the menu item. 4.
Checking Projector Status If your projector isn’t working correctly, first turn it off, wait for it to cool (the Power light stops flashing orange), and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status.
Status lights (continued) Light Status Description Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filter and vents are clear. Red The projector is overheating, which turns the lamp off automatically. Wait until the cooling fan stops, then unplug the power cord.
Solving Projector Operation Problems The power doesn’t turn on. ■ If the projector doesn’t turn on when you press the P Power button, make sure the power cable is connected to the projector and plugged into a working electrical outlet. ■ The power cable may be defective. Disconnect the cable from the outlet and contact Epson as described on page 178. ■ Check to see if the A/V mute slide (lens cover) is closed. The buttons on the projector don’t work.
■ If you are projecting from a DVD player or other video source, make sure you turn it on and press its Play button. You’ve connected a computer and see a blue screen with the message No Signal displayed. ■ Make sure the cables are connected correctly, as described on page 38. ■ If you’ve connected a computer and one or more video sources, you may need to press the Source Search button on the projector or one of the source buttons on the remote control to select the correct source.
The message Not Supported is displayed. ■ Make sure the correct input signal is selected in the Signal menu (see page 124). ■ Make sure your computer’s resolution doesn’t exceed UXGA (1600 × 1200) and the frequency or refresh rate is supported by the projector (see page 189). If necessary, change your computer’s resolution setting. Only part of the computer image is displayed. ■ Press the Auto button on the remote control. ■ Make sure the image Position setting is correct in the Signal menu.
The image contains static or noise. ■ If you’re using a computer cable longer than 6 feet, or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables away from the power cord as much as possible to prevent interference. ■ The video signal may be split between the computer and the projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your notebook computer and the projector, turn off the notebook’s LCD display.
You see vertical bands or the image still looks blurry after trying the solutions in the previous section. ■ ■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice vertical bands or some of the characters may look heavy or blurred. Press the Auto button on the remote control or the Enter button on the projector to reset the projector’s Tracking, Sync, and Position settings. note You must be projecting an image for this button to have any effect.
■ Try adjusting the Brightness and Contrast settings on the Image menu. ■ Check your computer display settings to correct the color balance. ■ The projector’s lamp may need to be replaced. See page 156 for instructions. ■ Make sure the correct input signal is selected in the Signal menu (see page 125). There is no sound, or the sound is not loud enough.
Solving Network Problems You don’t see your projector in the EMP Monitor window. ■ Make sure that you’ve connected the projector to the network and configured it correctly; see page 58. Also, make sure you’ve registered the projector with EMP Monitor; see page 139. ■ Make sure that Standby Mode in the projector’s Extended menu is set to Network On. ■ If the computer you are using is running Windows XP or 2000, you must be logged in as the Administrator. ■ Try restarting your computer.
Solving Problems ■ If you’ve changed any settings for your projector or network, or restarted your computer, allow a minute or two for the connection to appear. If you’re using AirPort, try turning AirPort off and then on again. ■ Make sure that you’re trying to connect to the right network.
■ If you’re using Access Point mode and you’re connecting to the wrong network, you may be experiencing signal interference from another network. Try resetting your access point or base station, then restart NS Connection. ■ If you’re using AirPort, the projector’s ESSID should match the AirPort network name, not the name of the AirPort base station. To check the network name, start the AirPort Admin utility, select your base station, and click Configure. Then click Show All Settings.
You can’t edit scenario files in EMP SlideMaker after they have been transferred to the USB drive. You can only edit scenarios before they are transferred. Open the scenario files saved on your hard drive, make any changes, then transfer the scenario to your USB drive. You can’t transfer your slideshow to the drive because you aren’t able to see the drive letter. You must connect the drive to your computer before you select Send Scenario from the Scenario Option(s) menu.
When using EasyMP, you see an ERR code at the bottom of the screen. Check for the code below. ERR Code Meaning 2, 50, 53, 245, or -103 Failed to start EasyMP. Turn the projector off, then turn it back on again. 51, 52, or 100 EasyMP processing error. If you’re using EMP NS Connection, try reconnecting to the projector. If you’re projecting through the projector’s USB port, reconnect the USB cable. -101 Communication was cut off. Check the access point connection (see page 65).
■ Make sure the Remote Receiver setting isn’t disabling both of the projector’s sensors (see page 127). ■ If any buttons are held for longer than 30 seconds, the remote enters sleep mode. Release any button that is held to wake the remote. Where To Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.
Before you call for support, please have the following information ready: ■ Product name (PowerLite 1815p) ■ Product serial number (located on the projector) ■ Proof of purchase (such as a store receipt) and date of purchase ■ Computer or video configuration ■ Description of the problem Purchase Supplies and Accessories You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.
Solving Problems
A Software Installation T he EasyMP software CD-ROM includes the software you need to use the projector’s EasyMP features—for presenting over a wireless network, transferring PowerPoint presentations to a memory card, and monitoring the projector from a remote location. Epson Projector Software CD-ROM includes EMP Monitor and EMP Network Manager for presenting and monitoring the projector from a remote location.
Mac System Requirements note You can present over a wireless network from Mac OS X using EMP NS Connection. However, EMP SlideMaker and EMP Monitor are available only for Windows. Before you install the software, make sure your Mac meets the following requirements: ■ Mac OS X 10.3 or later (OS X 10.3.9 to 10.4.5 recommended) ■ AirPort (802.11b) or AirPort Extreme (802.
3. Click Install, then follow the on-screen instructions to install your projector software. 4. When you see the Virtual Display screen, you can select one or more virtual displays to use for multi-screen projection (see page 90). Windows lets you use two by default, but you can select up to four more if you plan to use additional projectors. note If you select more virtual displays, your computer may slow down depending on its capabilities.
Software Installation
B Projector Installation T his appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
The projector includes security features to prevent its theft when installed or used in public locations: ■ Security cable attachment You can attach a commercially available security cable as shown below to secure the projector to a table or ceiling mount. ■ Kensington security slot The security slot is compatible with the MicroSaver security systems manufactured by Kensington. You can purchase this lock from Epson (see page 13).
C Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 16.8 million colors Brightness 3500 lumens (High Brightness mode) 2700 lumens (Low Brightness mode) Contrast ratio 500:1 Image size 30 to 300 inches Projection distance 2.7 to 48.2 feet (0.8 to 14.
Projection Lamp note Lamp life results will vary depending upon mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. Type UHE (Ultra High Efficiency) Power consumption 210 W Lamp life Approx. 2500 hours (High Brightness mode) Approx. 3000 hours (Low Brightness mode) Part number V13H010L40 Remote Control Range 20 feet (6 meters) Batteries (2) Alkaline AAA Dimensions Height 3.4 inches (86 mm), feet retracted Width 13.
Environmental Temperature Humidity (non-condensing) Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Operating: 20 to 80% RH Storage: 10 to 90% RH Operating altitude 0 to 7,500 ft (0 to 2,286 m) Safety and Approvals United States FCC 47CFR Part 15B Class B (DoC) UL60950 Third Edition Canada ICES-003 Class B CSA C22.2 No. 60950 CE Marking Directive 73/23/EEC Directive 89/336/EEC IEC 60950 Third Edition EN 55022, EN 55024 Pixelworks™ DNX™ ICs are used in this projector.
Compatible video formats 190 Technical Specifications Mode Refresh Rate (Hz) Resolution VGA EGA 70 640 × 350 VGA—60 VESA—72 VESA—75 VESA—85 VGA—120 60 72 75 85 120 640 × 480 640 × 480 640 × 480 640 × 480 640 × 480 SVGA—56 SVGA—60 SVGA—72 SVGA—75 SVGA—85 SVGA—120 56 60 72 75 85 120 800 × 600 800 × 600 800 × 600 800 × 600 800 × 600 800 × 600 XGA—60 XGA—70 XGA—75 XGA—85 XGA—120 60 70 75 85 120 1024 × 768 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA1—70 SXGA1—75 SXGA1—85 SXGA1—120 70 75 8
Compatible video formats (continued) Mode Refresh Rate (Hz) Resolution NTSC NTSC 4:43 PAL N-PAL M-PAL PAL—60 SECAM 60 60 50 50 60 60 50 — — — — — — — HDTV (720p) HDTV (720p) HDTV (1080i) HDTV (1080i) 60 50 60 50 — — — — TV480i TV625i SDTV (480p) SDTV (576p) 60 50 60 50 — — — — Technical Specifications 191
Technical Specifications
D Notices This appendix includes safety instructions and other important information about your projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not look into the lens when the projector is on. The bright light can damage your eyes. ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not operate the projector on its side, or while tilted to one side.
Notices ■ Do not operate the projector in a closed-in cabinet unless proper ventilation is provided. ■ If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. ■ You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. ■ Do not use the projector outside of the required temperature range of 41 to 95 °F (5 to 35 °C).
■ If the lamp breaks, ventilate the room to prevent gases contained in the lamp from being inhaled or coming in contact with the eyes or mouth. ■ If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from falling into your eyes when you open the lamp cover. WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
For Canadian Users This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.
Index A C A/V Mute button, 31 display settings, 131 Access Point mode, 65 to 75 Access point, checking IP address of, 72 to 73 Accessories, 13 Ad Hoc mode, 59 to 64 Air filter cleaning, 155 ordering, 13 replacing, 156 to 158 AirPort, configuring for wireless, 63 to 64, 73 to 75 Altitude, 133, 166, 189 Anti-theft device, 13, 17, 186 Aspect ratio, 187 Audio connecting equipment, 48 to 49 controlling volume, 33 problems, troubleshooting, 172 turning off (using A/V Mute), 31 using with scenarios, 108 Authenti
Connecting projector to audio equipment, 48 to 49 to computer, 38 to 41 to digital camera, 50 to external monitor, 47 to speakers, 49 to video equipment, 41 to 46 Continuous play setting, 105, 115 Contrast setting, 123 Custom screen, see User’s Logo Customized color mode, 28, 123 D Data encryption, 88 to 89 Default settings, restoring, 121 DHCP, 66, 70, 74, 174 Digital camera connecting to, 50 projecting images from, 101 to 102 Direct Power On, 19 Display order setting, 105 Distance from projector to scree
H L HDTV images, video formats, 191 Height of image, adjusting, 23 Help, 178 to 179 Help system, using, 164 Help, Epson, 10 High altitude, 133, 166 Lamp number of hours used, 159 to 160 ordering, 13 replacing, 156 to 159 specifications, 188 status light, 165 to 166 Lamp timer, resetting, 159 Language setting, 133 Laptop computer connecting to, 38 to 39 display problems, 21 to 22, 167 to 168 selecting source, 20, 30 LEAP authentication, 79 to 80 Lens, cleaning, 154 Lights, status, 165 to 166 Locking proje
Movie files projecting from external drive, 100 to 101 using in scenarios, 108 to 111 Movie Sending Mode, 92 to 93 MPEG, 92, 118 mpg, 118 mrk, 118 Multiple projectors, controlling, 35 to 36 Multi-screen color adjustment, 134 Multi-screen projection, 90 to 92, 183 N Network cable, 53 managing projector remotely, 135 to 150 problems, 173 to 175 projecting, 81 to 84 security, 87 to 89 setting, 142, 151 wired, 136 to 137 wireless, 52, 55 to 97 Network card compatible, 181 inserting, 52 Network settings, config
Projection lamp, see Lamp Projector cleaning, 154 disabling buttons, 131 distance from screen, 16, 187 installing, 185 to 186 lamp specifications, 188 locking, 83 monitoring remotely, 135 to 150 options, 13 password protection, 127 to 129 positioning, 16 to 17 resolution, 187 security features, 127 to 131, 186 specifications, 187 to 189 transporting, 161 troubleshooting, 163 to 166 turning off, 20 turning on, 17 to 19 unpacking, 12 viewing information about, 159 to 160 Projector ID, setting, 35 to 36 Q Qui
Scenarios adding movie files, 108 to 111 adding sound, 108 background color, 108 cells, 110 converting PowerPoint files, 105 to 106 creating, 105 to 112 default location, 108 exiting, 103, 117 presenting on the projector, 116 to 117 previewing, 113 problems, 175 to 176 rearranging, 110 running automatically, 114 to 115 transferring to drive, 114 to 115 transitions, 111 to 112 Screen blank, 21 to 22 distance from projector, 16, 187 ordering, 13 startup screen, creating, 129 to 130 Screen image, see Image Scr
Troubleshooting blank screen, 21 to 22, 167 to 168 cut-off image, 169 distorted image, 24 to 27 EasyMP problems, 175 to 177 image and sound problems, 167 to 172 network problems, 173 to 175 no signal, 21, 168 projector problems, 163 to 166 remote control problems, 177 tapered image, 24 to 27 wireless projection problems, 84 to 85, 173 to 175 Turning off picture (using A/V Mute), 31 Turning off projector, 20 U Unpacking projector, 12 USB cable, 12, 39, 41 display, 39 to 40 USB drive projecting from, 100 to