pro-insd.
pro-insd.fm Page ii Friday, November 7, 1997 5:20 PM All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent liability is assumed with respect to the use of the information contained herein.
pro-insd.fm Page iii Friday, November 7, 1997 5:20 PM Important Information About Your PowerLite 7000XB/5000XB Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.
pro-insd.fm Page iv Friday, November 7, 1997 5:20 PM FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
7000xbTOC.fm Page v Friday, November 7, 1997 5:21 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Contents Introduction ix Getting the Most Out of Your Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiii Safety Instructions . . . . . . . . . . . . . . . . . . .
7000xbTOC.fm Page vi Friday, November 7, 1997 5:21 PM Connecting to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Connecting to a PC Desktop Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Connecting to a PC Laptop Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Connecting to a Desktop Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Connecting to a PowerBook . . . . . . . . . . . . . . .
000xbTOC.fm Page vii Friday, November 7, 1997 5:21 PM 4 Using the ELP Link II Software 59 Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Connecting Needed Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Installing the Software from Windows 3.x . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Installing the Software from Windows 95 and Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . .
7000xbTOC.
pro-int.fm Page ix Friday, November 7, 1997 5:22 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Introduction The EPSON® PowerLite™ 7000XB and PowerLite 5000XB are compact, lightweight projectors that allow you to project full-color images and video onto a large screen for presentations. You can connect either projector simultaneously to three image sources: two PC or Apple® Macintosh® computer image sources plus one video source, such as a VCR or camcorder. You can also connect audio for each image source.
pro-int.fm Page x Friday, November 7, 1997 5:22 PM Your projector’s two speakers employ a built-in Spatializer 3D Sound System for rich, powerful audio output. You can even connect an external speaker when further amplification is required. A totally new, patent pending AVTSS system (Automatic Video Tracking and Synchronization Sensing) provides automatic image setup from a computer with a touch of a button, producing beautiful images quickly and easily.
pro-int.fm Page xi Friday, November 7, 1997 5:22 PM Getting the Most Out of Your Projector Your projector comes with a full set of features that enable you to control the settings for the image display, video, and audio. To get the most out of the projector, read this section for a quick summary of the important features.
pro-int.fm Page xii Friday, November 7, 1997 5:22 PM Optional Accessories To enhance your use of the projector, EPSON provides the following accessories: ● ● ● Carrying cases especially designed for the projector and its cables. Hard Carrying Case ELPKS06 Wheeled Soft Carrying Case ELPKS07 Soft Carrying Case ELPKS08 Replacement lamp and air filter. Lamp with Filter ELPLP04 Remote control receiver module with a cable for rear and ceiling mount projection.
pro-int.fm Page xiii Friday, November 7, 1997 5:22 PM About This Manual Chapter 1, “Installation,” gives step-by-step instructions on how to set up your projector and connect it to your computer, video source, or other optional equipment. Read the installation procedures that apply to your environment. Chapter 2, “Using the Projector,” describes how to turn on the projector and control simple projector settings using the remote control or the operation panel.
pro-int.fm Page xiv Friday, November 7, 1997 5:22 PM Safety Instructions Follow these safety instructions when setting up and using the projector: 1. Do not place the projector on an unstable cart, stand, or table. 2. Do not use the projector near water or sources of heat. 3. Use attachments only as recommended. 4. Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company. 5.
pro-int.fm Page xv Friday, November 7, 1997 5:22 PM 10. Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners. 11. Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or in a closed-in cabinet unless proper ventilation is provided. 12. Never push objects of any kind through cabinet slots.
pro-int.fm Page xvi Friday, November 7, 1997 5:22 PM Where to Get Help EPSON provides customer support through the following services: Electronic Support Services You can access helpful tips, specifications, DIP switch or jumper settings, drivers, Frequently Asked Questions (FAQs), sample files, application notes, and EPSON product bulletins 24 hours a day, 7 days a week, using a modem and one of the on-line services below. World Wide Web From the Internet, you can reach EPSON’s Home Page at http://www.
pro-int.fm Page xvii Friday, November 7, 1997 5:22 PM EPSON Forum on CompuServe ® Members of CompuServe can type GO EPSON at the menu prompt to reach CompuServe’s Epson America Forum. As an owner of an EPSON product, you are eligible for a free introductory CompuServe membership, which entitles you to an introductory credit and your own user ID and password. To take advantage of this offer in the U.S.
pro-int.fm Page xviii Friday, November 7, 1997 5:22 PM Before you call, please have the following information ready: ● ● ● ● Product name Product serial number Computer configuration Description of the problem You can purchase ink cartridges, paper, manuals, accessories, and parts from EPSON Accessories at (800) 873-7766 (U.S. sales only). In Canada, please call (800) 873-7766 for dealer referral..
pro-ch1.fm Page 1 Friday, November 7, 1997 5:22 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1 Installation This chapter describes how to unpack, set up, and connect your projector to other equipment. The projector must be connected to a computer or a video source such as a VCR, camcorder, or laser disc player.
pro-ch1.
pro-ch1.fm Page 3 Friday, November 7, 1997 5:22 PM Additional Components Depending on how you plan to use the projector, you may need additional components: ● ● ● ● ● To receive an S-Video signal, you need an S-Video cable. (One is usually provided with your video device.) A separate cable is required for each video source. To connect a second computer, you need a video and audio cable. To connect the projector to a Macintosh PowerBook, you need a video-out cable.
pro-ch1.fm Page 4 Friday, November 7, 1997 5:22 PM Setting Up the Projector 1. Place the projector on a sturdy, level surface within five feet of the computer or video source. ✦ Caution: Do not hold the projector by the lens. This can damage the lens. 2. Place the projector the proper distance from the screen. The distance between the projector and the screen determines the actual image size. Use the general guidelines in the table on the next page to determine the proper distance.
pro-ch1.fm Page 5 Friday, November 7, 1997 5:22 PM Horizontal distance from projector to screen Image size (diagonal) Minimum 300 inches Maximum 32.8 feet (10 m) 200 inches 22 feet (6.7 m) 28.5 feet (8.7 m) 100 inches 10.8 feet (3.3 m) 14 feet (4.3 m) 80 inches 8.9 feet (2.7 m) 11.5 feet (3.5 m) 60 inches 6.6 feet (2 m) 8.5 feet (2.6 m) 40 inches 4.3 feet (1.3 m) 5.6 feet (1.7 m) 30 inches 3.3 feet (1 m) 4.3 feet (1.3 m) 23 inches 3.3 feet (1 m) 3.
pro-ch1.fm Page 6 Friday, November 7, 1997 5:22 PM 5. To insert the batteries in the remote control, slide off the battery compartment cover as shown here 6. Insert the two AA batteries included with the projector. Make sure the polarity of the batteries is correct. TITLE 35_BATT1.eps EPSON AMERICA, INC. Documentation Department 20770 Madrona Avenue, Torrance, CA 90503 (310) 782-0770 DATE 27 August 1996 DRAWN BY Wendi Swanlund 7. Replace the battery compartment cover.
pro-ch1.fm Page 7 Friday, November 7, 1997 5:22 PM When replacing batteries, take the following precautions: ● ● ● Do not mix old and new batteries. Replace batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately. Remove batteries if you will not be using the projector for a long period of time.
pro-ch1.fm Page 8 Friday, November 7, 1997 5:22 PM Connecting to a PC Desktop Computer Before beginning, turn off the projector and computer if they are on. 1. Connect the video cable. monitor cable video cable Note: Computer configurations vary. See your computer manual for the location of the ports needed to connect your projector. 8 a. Connect one end of the video cable to the projector’s Computer In 1 port. (Use the Computer In 2 port if you are connecting a second computer.) b.
pro-ch1.fm Page 9 Friday, November 7, 1997 5:22 PM c. To also view the video on the computer monitor, connect the computer monitor’s monitor cable to the projector’s Monitor port. This is useful when you need to view the video output but the projection screen is behind you. d. Tighten the screws on all connectors. 2. Connect the main cable.
pro-ch1.fm Page 10 Friday, November 7, 1997 5:22 PM a. Connect the small end of the main cable to the projector’s Mouse/Com 1 port. (Use the Mouse/Com 2 port if you are connecting a second computer.) b. Connect one end of the PS/2 mouse cable included with the projector to the mouse terminal on the square end of the main cable. c.
pro-ch1.fm Page 11 Friday, November 7, 1997 5:22 PM 3. Connect the audio cable if needed. a. Connect one end of the audio cable to the Audio In 1 jack on the projector. (Use the Audio In 2 jack if you are connecting a second computer). b. Connect the other end of the audio cable to the speaker or audio out port on a sound card in the computer.
pro-ch1.fm Page 12 Friday, November 7, 1997 5:22 PM Connecting to a PC Laptop Computer Before beginning, turn off the projector and computer if they are on. 1. Connect the video cable. Note: Laptop configurations vary. See your computer manual for the location of the ports needed to connect your projector. 12 a. Connect either end of the video cable to the projector’s Computer In 1 port. (Use the Computer In 2 port if you are connecting a second computer.) b.
pro-ch1.fm Page 13 Friday, November 7, 1997 5:22 PM 2. Connect the main cable. The main cable connects the PS/2 mouse cable (needed to use the remote control as a mouse) and 9-pin serial cable (needed to use the ELP Link II software and the Effects buttons on the remote control) to the projector. PS/2 mouse cable 9-pin serial cable main cable a. Connect the small end of the main cable to the projector’s Mouse/Com 1 port. (Use the Mouse/Com 2 port if you are connecting a second computer.) b.
pro-ch1.fm Page 14 Friday, November 7, 1997 5:22 PM c. Connect the other end of the PS/2 mouse cable to the mouse port on your laptop. d. If your laptop uses a serial mouse, perform steps b and c using the serial mouse cable instead of the PS/2 mouse cable (not shown in the illustration). e.
pro-ch1.fm Page 15 Friday, November 7, 1997 5:22 PM 3. Connect the audio cable. a. Connect one end of the audio cable to the Audio In 1 jack on the projector. (Use the Audio In 2 jack if you are connecting a second computer). b. Connect the other end of the audio cable to your laptop.
pro-ch1.fm Page 16 Friday, November 7, 1997 5:22 PM Connecting to a Desktop Macintosh Before beginning, turn off the projector and Macintosh if they are on. 1. Connect the video cables. video-out cable (if supplied by Apple) Macintosh desktop adapter Macintosh desktop adapter video cable Note: Macintosh computer configurations vary. See your computer manual for the location of the ports needed to connect your projector. 16 a.
pro-ch1.fm Page 17 Friday, November 7, 1997 5:22 PM c. Connect the small terminal of the Macintosh video adapter to the other end of the video cable. d. Disconnect the monitor cable from the video port on the back of the Macintosh and connect the video cable (with Macintosh video adapter attached) to the video port. If a video-out cable was supplied with your Macintosh, connect one end to the video adapter and the other end to the video port on your Macintosh. e.
pro-ch1.fm Page 18 Friday, November 7, 1997 5:22 PM 2. Connect the main cable. The main cable connects the mouse cable (needed to use the remote control as a mouse) and serial cable (needed to use the ELP Link II software) from your Macintosh to the projector. MAC serial cable MAC mouse cable main cable 18 a. Connect the small end of the main cable to the projector’s Mouse/Com 1 port. (Use the Mouse/Com 2 to connect a second computer.) b.
pro-ch1.fm Page 19 Friday, November 7, 1997 5:22 PM c. Disconnect the mouse cable from the ADB port of the Macintosh and connect the mouse connector of the MAC mouse cable to the mouse port. d. If you are planning to use the ELP Link II software, connect either end of the serial cable to the serial terminal on the large end of the main cable. Connect the other end of the serial cable to the PRINTER or MODEM port on the back of your Macintosh. e. Tighten the screws on both connectors. 3.
pro-ch1.fm Page 20 Friday, November 7, 1997 5:22 PM Connecting to a PowerBook Your PowerBook must have a video-out capability in order to connect to the PowerLite 7000XB or 5000XB projector. Before beginning, turn off the projector and computer if they are on. 1. Connect the video cable. video-out cable (supplied by Apple) video cable Macintosh desktop adapter Note: PowerBook configurations vary. See your computer manual for the location of the ports needed to connect your projector. a.
pro-ch1.fm Page 21 Friday, November 7, 1997 5:22 PM b. Remove the small cover and set the DIP switches on the Macintosh video adapter in accordance with the resolutions you want to use (such as 16 inch mode). c. Connect the small terminal of the Macintosh video adapter to the other end of the video cable. d. Connect one end of the video-out cable that came with your PowerBook to the video-out connector on the back of the PowerBook. e.
pro-ch1.fm Page 22 Friday, November 7, 1997 5:22 PM 2. Connect the main cable. The main cable connects the mouse cable (needed to use the remote control as a mouse) and serial cable (needed to use the ELP Link II software) to the projector. MAC serial cable MAC mouse cable main cable 22 a. Connect the small end of the main cable to the projector’s Mouse/Com 1 port. (Use the Mouse/Com 2 port if you are connecting a second computer.) b.
pro-ch1.fm Page 23 Friday, November 7, 1997 5:22 PM d. If you are planning to use the ELP Link II software, connect either end of the serial cable to the serial terminal on the large end of the main cable. Connect the other end of the serial cable to the PRINTER or MODEM port on the back of your PowerBook. e. Tighten the screws on all connectors to make sure they are fastened securely. 3. Connect the audio cable. EPSON/PowerLite 5000 - File: AUD-PBK.eps W. Swanlund MOD> 12/14/96 a.
pro-ch1.fm Page 24 Friday, November 7, 1997 5:22 PM Connecting to a High-End Workstation Although the PowerLite 7000XB has a maximum resolution of 1024 × 768 pixels, it’s capable of remapping input resolutions up to 1280 × 1024 pixels. Since 1028 × 1024 pixels is the default resolution for most leading workstations, this capability makes the PowerLite 7000XB the best portable solution for the display of workstation video output. There is no standard for workstation video output.
pro-ch1.fm Page 25 Friday, November 7, 1997 5:22 PM Note: The PowerLite 7000XB and PowerLite 5000XB projectors are not compatible with a cable TV-style F connector. You can connect the projector to both an S-Video and a composite video source at the same time. However, the projector automatically selects the S-Video as the video source. To display composite video, first disconnect the S-Video source.
pro-ch1.fm Page 26 Friday, November 7, 1997 5:22 PM To connect a video source to the projector: 1. Turn off the projector and video source if they are on. 2. If your video source uses a small, round, one-prong composite (RCA) video connector, you’ll need the audio/visual cable that comes with the projector. If your video source uses a large, round, four-prong S-Video connector, you will need to purchase an S-Video cable. 3.
pro-ch1.fm Page 27 Friday, November 7, 1997 5:22 PM 5. For S-Video, insert one end of the S-Video cable into the projector’s S-Video jack. Insert the other end into the S-video-out jack of your video source.
pro-ch1.fm Page 28 Friday, November 7, 1997 5:22 PM 2. Connect the cable’s 3.5 mm stereo miniplug to the projector’s Audio Out jack. 3. Connect the RCA plugs to the external amplified speaker or PA system. Insert the cable’s red plug into the Audio In R jack, and the white plug into the Audio In L jack.
pro-ch2.
pro-ch2.fm Page 30 Monday, November 10, 1997 1:36 PM About Your Projector The illustration below identifies the parts of your projector.
pro-ch2.fm Page 31 Monday, November 10, 1997 1:36 PM Turning the Equipment On and Off Always turn on the projector and its attached equipment in the following order: 1. Video source (such as a VCR), if your video source is not your computer 2. Audio source (if different from computer or video source) 3. Projector 4. External amplified speaker or PA system (if necessary) 5. Computer Turning the Projector On and Off 1. Remove the projector lens cap. 2.
pro-ch2.fm Page 32 Monday, November 10, 1997 1:36 PM When you want to stop projecting images, press the Power button again. The fan remains on, the projection lamp indicator flashes orange for about 60 seconds, and the power indicator changes to orange as the projector cools off. power indicator projection lamp indicator When the projector has cooled off, flashing stops and the power indicator changes to orange.
pro-ch2.fm Page 33 Monday, November 10, 1997 1:36 PM Focusing and Positioning the Screen Image When an image appears on screen, check that it is in focus and correctly positioned on the screen. focus ring zoom ring ● ● To focus the image, rotate the focus ring (the inside ring on the lens). To adjust the size of the image, rotate the zoom ring (the outside ring). Rotate the zoom ring clockwise to make the screen image larger or counterclockwise to make it smaller.
pro-ch2.fm Page 34 Monday, November 10, 1997 1:36 PM If you need to raise or lower the image on the screen, extend or retract the adjustable foot at the bottom of the projector as follows: foot release button adjustable foot 1. Stand behind the projector and support the front of it while you press the purple button above the lens. This unlocks the adjustable foot so it can move up and down. Don’t let the projector drop. ✦ Caution: Don’t hold the projector by its lens. This can damage the lens. 2.
pro-ch2.fm Page 35 Monday, November 10, 1997 1:36 PM Auto Button If you’re using image input from a computer, you can press the Auto button after fitting the image to the screen. Pressing the Auto button automatically adjusts the computer signal input to the current projector settings. Press the Auto button while the image fills the entire screen of your computer, like a maximized Windows screen.
pro-ch2.fm Page 36 Monday, November 10, 1997 1:36 PM The Resize button cannot be used with XGA for the PowerLite 7000XB, or with SVGA for the PowerLite 5000XB. There’s a Resize button on both the control panel and remote control.
pro-ch2.fm Page 37 Monday, November 10, 1997 1:36 PM Using the Remote Control pointer button top multi-purpose button bottom multi-purpose button The remote control uses a line-of-sight infrared signal. To use the remote control, point it towards one of the remote control receivers located at the front and back of the projector. You can use the remote control up to about 32.8 feet (10 meters) from the projector. (This distance may be shorter if the remote control batteries are low.
pro-ch2.fm Page 38 Monday, November 10, 1997 1:36 PM infrared receiver; or other equipment emitting infrared energy is present (such as a radiant room heater). Correct these conditions to use the remote control or control the projector from a computer. This table summarizes the functions on the remote control. 38 Button Function Video Switches from computer to video. Menu Displays or hides the menu. Computer Switches between Computer 1 and Computer 2, and from video to computer.
pro-ch2.fm Page 39 Monday, November 10, 1997 1:36 PM Button Function Resize Switches the display dot mode and resize mode for the following types of input: VGA, SVGA and SXGA for the PowerLite 7000XB, and VGA and XGA for the PowerLite 5000XB. Custom Assigns functions to the Effects keys using ELP Link II. Freeze Keeps the current computer or video image on the screen. Mute Cuts off audio. – Volume + Power Adjusts the volume. Starts or stops the projector.
pro-ch2.fm Page 40 Monday, November 10, 1997 1:36 PM The following table summarizes the functions on the control panel. Button Function Power Starts or stops projection. Video Switches from computer to video. Computer Switches between Computer 1 and Computer 2, and from video to computer. Menu Displays or hides the menu. Up, down arrows Synchronizes the computer’s graphic signal.
pro-ch2.fm Page 41 Monday, November 10, 1997 1:36 PM Projector Status Indicators The power and lamp indicators at the top of the projector tell you the projector’s operating status. power indicator projection lamp indicator ✦ Caution: A red indicator warns you if a serious problem occurs. See Chapter 6, “Troubleshooting,” for what to do if a warning light comes on. Power Indicator Light status Meaning Steady orange Sleep mode. (The projector is plugged in, but not projecting.
pro-ch2.fm Page 42 Monday, November 10, 1997 1:36 PM Projection Lamp Indicator Light status Meaning Steady green Projection lamp is on. Flashing green The projector is warming up. Orange and red Projection lamp needs replacing. flashing alternately 42 Flashing orange Projector lamp is cooling down. Steady red Projector lamp has burned out. Replace it to project images. Flashing red Problem with projection lamp or lamp power supply.
pro-ch3.fm Page 43 Friday, November 7, 1997 5:23 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 3 Using the Projector Menus The six projector menus enable you to control your projector. ● ● ● ● ● ● The Video menu controls the computer image, such as brightness and contrast, when the computer is the image source. The Video menu controls the video image, such as brightness and color saturation, when the image source is video, such as a VCR.
pro-ch3.fm Page 44 Friday, November 7, 1997 5:23 PM Accessing the Main Menu The projector menus can be accessed using either the projector control panel or remote control. To display the Main menu, first press the Computer or Video button on the control panel or remote control, then press the Menu button. The Main menu appears: Press the Menu button again to hide the menu. Changing a Menu Setting To change a menu setting: 1.
pro-ch3.fm Page 45 Friday, November 7, 1997 5:23 PM 2. Press the up or down arrows (control panel) or press the top or bottom of the pointer button (remote) to scroll through the menu choices.
pro-ch3.fm Page 46 Friday, November 7, 1997 5:23 PM 3. Press either the Enter button (control panel) or the top or bottom multi-purpose button (remote) to display a submenu. Enter button top multi-purpose button bottom multi-purpose button A sub-menu such as the following appears. Note: Sub-menus differ, depending on if the current image source is Computer or Video.
pro-ch3.fm Page 47 Friday, November 7, 1997 5:23 PM 4. Press the up or down arrows (control panel) or the top or bottom of the pointer button (remote) to scroll through the menu choices. 5. Press either the left or right arrow buttons (control panel) or the right or left sides of the pointer button (remote) to change the setting. 6. When you are finished changing settings, press the Menu button again to hide the menu, or select RETURN and press Enter to go back to the Main menu.
pro-ch3.fm Page 48 Friday, November 7, 1997 5:23 PM Note: The computer must be connected and operating, and the image source on the projector must be set to Computer for you to access these menu options. Menu item Description Brightness Lightens or darkens the overall image. Increase brightness to lighten an image, or decrease it to darken the image. Contrast Adjusts the difference between light and dark areas. Increase the contrast to make light areas lighter and dark areas darker.
pro-ch3.fm Page 49 Friday, November 7, 1997 5:23 PM Menu item Description Position Select this item and then press the Enter button (control panel) or either multi-purpose button (remote) to enter the screen position adjustment mode. Then use the pointer button or up, down, left, and right buttons (control panel) to move the screen position in the corresponding direction.
pro-ch3.fm Page 50 Friday, November 7, 1997 5:23 PM Video Menu (Image source = Video) The Video menu enables you to make adjustments to the projected image. The following options are available when the image source is Video. Note: The video source (such as a VCR or camcorder) must be connected and operating, and the image source on the projector must be set to Video for you to access these menu options. 50 Menu item Description Brightness Lightens or darkens the overall image.
pro-ch3.fm Page 51 Friday, November 7, 1997 5:23 PM Menu item Reset Description Returns all Video menu items to their initial factory defaults. Select this item and then press either multi-purpose button (remote) or the Enter key (control panel) to display the confirmation screen. Next, select Yes and then press a multi-purpose button (remote) or the Enter key (control panel) to reset the Video Menu.
pro-ch3.fm Page 52 Friday, November 7, 1997 5:23 PM Menu item Reset Description Returns all Audio menu items to their initial factory defaults. Select this item and then press the Enter button (control panel) or either multi-purpose button (remote) to display the confirmation screen. Next, select Yes and then press the Enter button (control panel) or a multi-purpose button (remote) to reset the Audio menu.
pro-ch3.fm Page 53 Friday, November 7, 1997 5:23 PM Menu item Description Color Temperature Adjusts the whiteness of the screen. The H setting provides a cold white, M a standard white, and L a warm white. To set the color temperature setting more precisely, press the right arrow button past H, M, and L to select the User item. This displays a screen showing USER RED and USER BLUE.
pro-ch3.fm Page 54 Friday, November 7, 1997 5:23 PM Menu item Description View Change Specifies the screen switching effect to use when the input source is changed. Off No screen switching effect. Upper Left Lower Right Original source screen shrinks from upper left to lower right, and new source screen expands from upper left to lower right. Left-Right: OutsideMiddle Original source screen shrinks from left to right, and new source screen expands from left to right.
pro-ch3.fm Page 55 Friday, November 7, 1997 5:23 PM To open the Custom menu, press the top multi-purpose button or select CUSTOM from the Main menu. ZOOM is highlighted and the words PRESENT SET are displayed after it. Refer to the table below for a description of the various zoom functions. To change PREVIEW or STROBE settings, select the function you want, then press the top multi-purpose button.
pro-ch3.fm Page 56 Friday, November 7, 1997 5:23 PM Menu item Function Description Zoom Screen Shift Press the pointer button to zoom in on a portion of the enlarged display. You can move the image up, down, left, right, and diagonally to closely view any part of the display. Preview Press the bottom multi-purpose button, and then check if the value next to the Preview menu is New Set or Present Set. If the value is New Set, press the bottom multi-purpose button to toggle the value.
pro-ch3.fm Page 57 Friday, November 7, 1997 5:23 PM Menu item Function Description Number of Frames, Time Press the top multi-purpose button while the strobe effect is running to display a screen specifying the number of frames flashed and the time interval between them. You can specify the number of frames as 4, 9, or 16, and the time interval from 0.1 to 1 second in 0.1 second increments. Press the top multi-purpose button again to clear the setting screen.
pro-ch3.
pro-ch4.fm Page 59 Monday, November 10, 1997 1:37 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 4 Using the ELP Link II Software The ELP Link II software is a utility you can run from your desktop or laptop computer to control projector features and configure special effects buttons on the remote control.
pro-ch4.fm Page 60 Monday, November 10, 1997 1:37 PM Installing the Software ELP Link II software can be used with the following operating systems: ● ● ● Windows 3.x Windows 95 Macintosh OS System 7 and OS System 8. Connecting Needed Cables Before installing the software, make sure the projector is properly connected to your computer. See Chapter 1, “Installation,” for instructions about how to install the serial and mouse cables needed to use the Link II software.
pro-ch4.fm Page 61 Monday, November 10, 1997 1:37 PM 2. In the Windows Program Manager, click on the File menu, then on Run. The Run dialog box appears: 3. Type A:\SETUP (or B:\SETUP as appropriate), then press Enter or click OK. The ELP Link II introduction appears. Press C to continue. 4. To accept the default location for where the software should be installed, press C to continue. Otherwise, enter a new directory name and then press C. 5.
pro-ch4.fm Page 62 Monday, November 10, 1997 1:37 PM Installing the Software from Windows 95 Perform the following steps to set up the software: 1. Insert the Link II for Windows installation diskette into a diskette drive (A: or B: as appropriate). 2. Click Start. 3. Click the Run menu option. The Run dialog box appears: 4. Type A:\SETUP (or B:\SETUP as appropriate), then press Enter or click OK. The ELP Link II introduction appears. Press C to continue. 5.
pro-ch4.fm Page 63 Monday, November 10, 1997 1:37 PM 7. A summary screen appears stating how much free hard disk space is required to run the software and how much is available. If sufficient disk space is available, press C. Otherwise, press X (exit) to free up some disk space; then restart the installation program from step 1. 8. You see a prompt to create the installation directory you specified in step 6. Press Y (yes).
pro-ch4.fm Page 64 Monday, November 10, 1997 1:37 PM Launching the Software 1. Double-click the ELP Link II program icon from the Windows 3.x ELP Link II program group or Mac OS ELP Link II folder, or select ELP Link II from the Windows 95 Programs menu. The ELP Link II program icon appears minimized at the bottom of your screen. 2. Double-click the ELP Link II program icon. The ELP Link II main dialog box appears.
pro-ch4.fm Page 65 Monday, November 10, 1997 1:37 PM Function Description and Usage The function list on the left side of the ELP Link II main dialog box shows the functions available for assignment to an Effects button. To assign the functions, see page 67. The table below describes these functions and how to use them. Note: To use the Effects buttons, the ELP Link II software must be running and the computer connected to the projector.
pro-ch4.fm Page 66 Monday, November 10, 1997 1:37 PM Function Description and usage Bar Creates a horizontal or vertical bar. You can use this function to highlight a portion of the screen with a horizontal or vertical bar. Press the Effects key assigned to this effect. Move the bar using the remote pointer button. Press the bottom multi-purpose button to lock the bar in place. Stamp Leaves one or several copies of the pre-selected image on the screen. Press the Effects key assigned to this effect.
pro-ch4.fm Page 67 Monday, November 10, 1997 1:37 PM Assigning Functions There are three ways to assign functions to each of the five Effects buttons on the remote control: ● ● ● Drag and drop a function from the function list to the Effects button you want to customize. Click a function in the function list, click the Effects button number you want to customize, then click Customize. Select the function from the function list, and then press the Effects button on the remote control.
pro-ch4.fm Page 68 Monday, November 10, 1997 1:37 PM Setting Effect Options Once you have assigned functions to one or more Effects buttons, you can specify detailed options for each function. To set detailed options, click Detail Setting. A dialog box similar to the following appears. (The options and tabs displayed depend on which functions are currently assigned to the Effects buttons.) Click the tab for the function you want to adjust, then make any settings you wish.
pro-ch4.fm Page 69 Monday, November 10, 1997 1:37 PM Function Options Line Width Specify the line width, from 1 to 32 points. Grid Specify whether to have the line “snap” to the corners of a grid by entering the size of the sides of the box, in pixels (dots). Color Choose a color for the line. Transparent Click this check box to make the background text or image visible through the line. Width Specify the line width, from 1 to 32 points. Color Choose a color for the line.
pro-ch4.fm Page 70 Monday, November 10, 1997 1:37 PM Function Options Change Cursor Click on the cursor shape to be used. Clear Screen No options available. Macro Key Enter up to 16 characters, including combinations such as Ctrl + A, in the Registration Keys Macro field. The Backspace and Delete keys are also recorded. Click on the Clear button to clear the current key assignment. Click on the Registration button to save more than one set of key assignments.
pro-ch4.fm Page 71 Monday, November 10, 1997 1:37 PM Saving and Recalling Effects Key Button Assignments To save Effects button assignments, click Execute. To save multiple sets of button assignments, click Registration and specify a name for the current settings. To recall a saved set of assignments, select its name from the Setting menu. To delete a set of assignments from the Registration List, select its name and then click Delete. To exit without saving the settings, click Exit.
pro-ch4.fm Page 72 Monday, November 10, 1997 1:37 PM Controlling Projector Features You can use the ELP Link II software to control the following features: ● ● ● Projector Controls Test Pattern Color Properties. Displaying the Projector Set Window 1. Double-click the ELP Link II program icon from the Windows 3.x program group or Mac OS ELP Link II folder, or select ELP Link II from the Windows 95 Programs menu. The ELP Link II program icon appears minimized on your screen. 2.
pro-ch4.fm Page 73 Monday, November 10, 1997 1:37 PM Using the Quick Change Toolbar To quickly change some basic projector settings, click one of the toolbar buttons described below: Power On, Off Volume Up, Down, Mute Contrast Up, Down Brightness Up, Down Blank, Custom, Freeze Auto, Resize Video, Computer Changing Projector Settings 1. Click Projector Control on the Projector Set dialog box.
pro-ch4.fm Page 74 Monday, November 10, 1997 1:37 PM 2. Click on the tab for the settings you want to adjust. 3. Change one or more of the following options. Computer Tab Option Description Brightness Adjusts screen brightness. Contrast Adjusts screen contrast. Sync Adjusts the sych (synchronization) to remove screen flicker. Tracking Adjusts tracking to remove horizontal lines. Position Adjusts the horizontal and vertical screen position.
pro-ch4.fm Page 75 Monday, November 10, 1997 1:37 PM Option Description Mode Selects the signal format. You can select AUTO, PAL, NTSC, or SECAM. AUTO automatically adjusts the image to the signal received. Pattern Display Displays the test pattern currently selected. Reset Resets all fields to their default values. Sound Tab Option Description Volume Adjusts sound volume. Tone Adjusts sound tone.
pro-ch4.fm Page 76 Monday, November 10, 1997 1:37 PM Option Tab Option Description Blank To Specifies if a blank screen is to be displayed when no signal is connected. Source Prompt Temporarily displays a prompt on the projector screen identifying which source (computer or video) is providing the image. Install Specifies how the projector is being used: Rear Proj Use this setting when projecting to the back of a screen so the image is flipped left to right.
pro-ch4.fm Page 77 Monday, November 10, 1997 1:37 PM Custom Tab Option Description Customize Function Zoom Zooms in on the screen image. Preview Displays the images from all the connected devices on the screen at one time. Strobe Displays the selected images in the specified number of frames and time interval. Frame Count Specifies the number of frames in which to show the image. Frame Times Specifies the interval for the strobe, in seconds.
pro-ch4.fm Page 78 Monday, November 10, 1997 1:37 PM Changing the Test Pattern 1. Click Test Pattern on the Projector Set dialog box. The following window appears: 2. You can display a test pattern when setting up the projector to verify that the projector is working properly. Choose one of the following: Color Image Displays a color bar test pattern. Gray Scale Displays a gray scale test pattern. Focus Pattern Displays a character-based focus pattern.
pro-ch4.fm Page 79 Monday, November 10, 1997 1:37 PM Setting the Image Color Property 1. Click Color Property on the Projector Set dialog box. The Color Property window appears. 2. Specify a color temperature: H M L User High (more blue) Medium (normal white) Low (more red) Create a custom color temperature by using the slide bars to specify the amount of red and blue. 3. Specify an image gamma: Gamma 1 Gamma 2 Gamma 3 Provides a dynamic and contrastive image.
pro-ch4.
pro-ch5.fm Page 81 Friday, November 7, 1997 5:24 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 5 Maintenance Your projector needs little maintenance. You should keep the lens clean because any dirt or smears appear on the screen. You also need to periodically clean the air filter at the bottom of the projector. A clogged air filter can block ventilation needed to cool the projector and keep it from overheating. The only parts you should replace are the lamp and air filter.
pro-ch5.fm Page 82 Friday, November 7, 1997 5:24 PM can injure you severely. Do not try to service this product yourself, except as specifically explained in this Owner’s Manual. Refer all other servicing to qualified service personnel. Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. Lightly wipe the lens surface with a soft, dry, lint-free cloth. To remove dirt or smears on the lens, moisten a soft cloth with an alcohol-based cleaner and gently wipe the lens surface.
pro-ch5.fm Page 83 Friday, November 7, 1997 5:24 PM Cleaning the Air Filter Clean the air filter at the bottom of the projector after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. To clean the air filter, follow these steps: 1. Turn off the projector and unplug the power cable. 2.
pro-ch5.fm Page 84 Friday, November 7, 1997 5:24 PM 4. The filter is attached to the inside of the filter cover. It is recommended that you use a small vacuum cleaner designed for computers and other office equipment to clean the filter. If you don’t have one, use a dry, lint-free cloth. If the dirt is difficult to remove or if the filter is torn, replace it. Contact your dealer or call EPSON Accessories at (800) 873-7766 in the United States and Canada to obtain a new one. Request part number 1032043.
pro-ch5.fm Page 85 Friday, November 7, 1997 5:24 PM 3. Use a screwdriver, coin, or similar object to loosen the two retaining screws on the lamp cover. When the screws are loose, lift off the lamp cover. (You cannot remove these screws.) 4. Use a screwdriver, coin, or similar object to loosen the two screws holding the lamp in position. (You cannot remove these screws.
pro-ch5.fm Page 86 Friday, November 7, 1997 5:24 PM 5. Lift up the handle and pull out the lamp. 6. Gently insert the new lamp by lowering it into position. Make sure it is inserted securely. 7. Tighten the screws you loosened in step 4. 8. Replace the lamp cover and tighten the cover screws. (Make sure the lamp cover is securely fastened. The projector turns itself off if the lamp cover is open.
pro-ch6.fm Page 87 Friday, November 7, 1997 5:25 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 6 Troubleshooting This chapter describes the problems indicated by the warning lights and provides information on how to solve problems with the projector. It is divided into the following sections: Problems with the projector. See this section if the projector is not ● working and to find out what the warning lights are indicating. Problems with the screen image.
pro-ch6.fm Page 88 Friday, November 7, 1997 5:25 PM Problems with the Projector If you have problems with the projector, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the warning lights at the top of the projector. These lights alert you to problems with projector operation .
pro-ch6.fm Page 89 Friday, November 7, 1997 5:25 PM ◗ The projection lamp light is flashing orange and you cannot turn on the projector. The lamp is cooling down. Wait until the light turns off and then turn on the projector. ◗ The power light does not come on. Turn off the projector, check that the power cable is connected securely both at the power outlet and the projector, and press the Power button again. ◗ Projected images get darker or start to deteriorate, or the projection lamp light is red.
pro-ch6.fm Page 90 Friday, November 7, 1997 5:25 PM ◗ The projection lamp and power lights are flashing at the same time. An abnormality may have occurred in the projector. Turn off the projector and unplug the power cord. Then plug the power cord back in and turn on the projector. If nothing changes, call the service center. ✦ Warning: Except as specifically explained in this User’s Guide, do not attempt to service this product yourself.
pro-ch6.fm Page 91 Friday, November 7, 1997 5:25 PM You also may need to modify existing presentation files if you created them for a different resolution. See your software manual for specific information. ◗ The message NO SIGNAL is displayed. An image source not connected to the projector is selected, the signal is not being output from the computer, or the signal is not reaching the projector. Make sure the connectors are securely attached to both the projector and the image source.
pro-ch6.fm Page 92 Friday, November 7, 1997 5:25 PM ◗ The colors of the image are not right. The color balance may be incorrect. If you’re displaying a computer image, adjust the red, green, and blue settings in the Video menu. If you’re displaying video, adjust the color and tint (NTSC only) settings on the Video menu. ◗ There is no sound. First check that the volume setting is not turned all the way down and that the audio/visual cable is securely attached to both the projector and the audio source.
pro-ch7.fm Page 93 Friday, November 7, 1997 5:25 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 7 Technical Specifications General Type of display Liquid crystal panel, Thin Film Transistor (TFT) Size of liquid crystal panels 1.32 inches (33.6 mm) Resolution PowerLite 7000XB: 1024 (horizontal) × 768 (vertical) pixels PowerLite 5000XB: 800 (horizontal) × 600 (vertical) pixels Image size 21 to 300 inches (0.
pro-ch7.fm Page 94 Friday, November 7, 1997 5:25 PM Projector Lamp Mechanical 94 Remote control range 32.8 feet (10 meters) ± 30° Internal speaker system 2 × 2W stereo Optical aspect ratio 4 × 3 (horizontal × vertical) Zoom ratio 1:1.3 Tilt angle 0 ° — 15° Type Discharge Lamp Power 150 W Life 2000 hours at 50% brightness Part number ELPLP04 Height 6.3 inches (159 mm) Width 9.7 inches (245 mm) Depth 15.0 inches (380 mm) with lens Weight PowerLite 7000XB: 14.8 lb (6.
pro-ch7.fm Page 95 Friday, November 7, 1997 5:25 PM Electrical Rated frequency 50/60 Hz Power supply PowerLite 7000XB: 100 to 120 VAC, 2.7 A, 50/60 Hz 200 to 240 VAC, 1.6 A, 50/60 Hz PowerLite 5000XB: 100 to 120 VAC, 2.7 A, 50/60 Hz 200 to 240 VAC, 1.
pro-ch7.fm Page 96 Friday, November 7, 1997 5:25 PM Supported Monitor Displays PowerLite 5000XB The PowerLite 5000XB displays images at a resolution of 800 × 600 pixels. To display a higher resolution image (1024 × 768 mode), the projector compresses it to 800 × 600.
pro-ch7.fm Page 97 Friday, November 7, 1997 5:25 PM PowerLite 7000XB The PowerLite 7000XB displays images at a resolution of 1024 × 768 pixels. To display a higher resolution image (1280 × 1024 mode), the projector compresses it to 1024 × 768. The following table lists the display formats supported by the projector: Computer type Formats Resolutions IBM PC and IBM PC compatible VGA, VESA, EGA CGA, SVGA, XGA.
pro-ch7.fm Page 98 Friday, November 7, 1997 5:25 PM Monitor and Computer In 1/2 connector pin assignments The Monitor and Computer In 1/2 connectors are female video RGB, 15-pin micro-D-style connectors.
pro-gls.fm Page 99 Friday, November 7, 1997 5:25 PM ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Glossary Brightness. The balance of light and dark shades in an image. Composite video. A type of video signal that encodes picture, luminance, and synchronization information so it can be carried in one signal. Contrast. A measure of the tonal differences between the highlights and shadows of an image.
pro-gls.fm Page 100 Friday, November 7, 1997 5:25 PM Point. A measurement of drawn or printed objects. One point equals 1/72 inch. Resolution. A measure of the amount of detail contained in an image. Resolution can be measured in dots per inch or in pixels. Image sharpness and clarity improve as resolution increases. RGB. A type of color scheme that defines color as percentages of red, green, and blue. S-Video. A type of video signal used in S-VHS videotape formats.
7000xbIX.
7000xbIX.
7000xbIX.
7000xbIX.
7000xbIX.
7000xbIX.
