EPSON PowerLite 600p/800p/810p Multimedia Projector ® ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
C Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Getting the Most from Your Projector . . . . . . . . . . . . . . . . . . 2 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Reading This Manual Online. . . . . . . . . . . . . . . . . . . . . . 3 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 4 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Unpacking the Projector . . . .
iv 2 Using the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3 Using the Remote Control . . . . . . . . . . . . . . . . . . . 31 Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 20 Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 20 What To Do If You See a Blank Screen . . . . . . . . . . . . 22 Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Focusing and Zooming Your Image . . . . . . . . . . . . . . .
4 5 Fine-tuning the Projector . . . . . . . . . . . . . . . . . . . . 41 Using the Projector’s Menu System . . . . . . . . . . . . . . . . . . . 42 Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . 43 Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Repositioning the Image . . . . . . . . . . . . . . . . . . . . . . . . 46 Adjusting Image Appearance . . . . . . . . . . . . . . . . . . . . . 46 Saving and Recalling Computer Settings . . . . . . . . .
A B C Connecting to Additional Equipment . . . . . . . 81 Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Connecting to an External Audio System . . . . . . . . . . . 83 Connecting to a PC Desktop Computer . . . . . . . . . . . . . . . 84 Connecting the Computer Cable . . . . . . . . . . . . . . . . . . 84 Connecting the Mouse Cable. . . . . . . . . . . . . . . . . . . . . 86 Connecting the Audio Cable . . . . . . . . . . . . . . . . . . . . .
W - Welcome The EPSON ® PowerLite® 600p, 800p, and 810p are portable projectors that weigh less than 10 pounds and offer up to 2000 ANSI lumens of brightness. From classrooms to auditoriums, your full-color presentations and videos will be bright and visible even in ordinary room lighting. Images are displayed at a resolution of 1024 × 768 pixels (PowerLite 800p and 810p) or 800 × 600 pixels (PowerLite 600p). The 0.9-inch LCD provides a high contrast ratio for incredibly vivid images and clear text.
Getting the Most from Your Projector note You can connect a maximum of four sources at the same time. Your EPSON PowerLite projector is a highly versatile presentation tool. You can connect it to one or two computer sources and up to three video sources and easily switch between them. You can also include sound for up to three of the sources.
If you’re permanently installing the projector, you may wish to connect external speakers or a public address system to the projector’s Audio Out port; see page 83. Using Your Documentation To connect the projector to your laptop and get your presentation up and running fast, see the Quick Setup sheet in your Owner’s Kit. This book contains all the information you need to set up and use your projector.
note If the hand changes to an index finger while holding the mouse pointer over text, you can click to jump to a related topic. You can move quickly to the topic of your choice by clicking in the table of contents on the left side of the screen. You can also use the arrow buttons in the toolbar or on the vertical scroll bar on the right side of the screen to move through the manual. For more information, see your Acrobat Reader online guide.
If you still need help after checking this User’s Guide and the sources listed above, you can use the EPSON PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on the card in your Owner’s Kit. Or take advantage of EPSON’s automated support services 24 hours a day. See page 79 for more information.
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: remote control power cord CD-ROM (not needed to use the projector) projector batteries computer cable A/V cable USB cable PS/2 mouse cable Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location.
Additional Components Depending on how you plan to use the projector, you may need additional components: ■ To receive an S-Video signal, you need an S-Video cable. (One is usually provided with your video device.) ■ To receive a component video signal from a VCR or other video device, you need a VGA-to-component video cable. You can purchase this from EPSON; see page 8. ■ To connect two computers to the projector at the same time, you need a DVI/analog interface cable.
Optional Accessories To enhance your use of the projector, EPSON provides the following optional accessories: Product Product number Replacement lamp and air filter ELPLP15 Customized carrying cases: Samsonite wheeled soft case ATA molded hard shell case ATA shipping case Soft shoulder bag ELPKS35 ELPKS40 ELPKS41 ELPKS13 Ceiling mount ELPMB36 Kensington security lock ELPSL01 Projection screens: 50-inch portable screen 60-inch Insta Theatre screen 80-inch Insta Theatre screen ELPSC06 ELPSC07 ELPS
1 Setting Up the Projector This chapter tells you how to set up the projector for a laptop computer or video presentation. If you need to set up the projector for a permanent installation or connect it to a desktop or workstation computer, see Appendix A.
Positioning the Projector Before connecting the projector, you need to decide where to place it. The location you choose depends on the size of the room and what you are projecting. ■ Place the projector on a sturdy, level surface, approximately 2.85 to 41 feet from the screen. ■ Make sure there is plenty of space for ventilation around and under the projector.
If you place the projector below the level of the screen, you’ll have to tilt it up by extending the feet as shown. Tilting the projector upward causes the image to lose its square shape, but you can correct the distortion by pressing the Keystone button as described in the next chapter. note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector’s left side.
Connecting to a Laptop Computer note To connect to desktops and other computer systems, see Appendix A. If you have an iBook with an RCA videoout port, follow the instructions for connecting to a video device on page 16. You can connect the PowerLite projector to any computer that has a standard video output (monitor) port, including PC notebook and laptop computers, Macintosh PowerBooks, and hand-held devices.
Connecting the Cable for Remote Mouse Control Using the remote control as a wireless mouse lets you control your computer and click through slideshow-style presentations, such as PowerPoint, from up to 30 feet away (for details, see page 39). This gives you more flexibility in delivering your presentation, since you won’t need to stand near your computer. The USB cable also provides audio support.
Amplifying Computer Audio note If you connected the USB cable, you may not need a separate audio cable to amplify audio from your computer. Your laptop probably has its own sound system; however, it may not be adequate for your presentation. If you need more volume or better sound quality, you can connect a stereo, mini-jack audio cable (not included). 1. Connect one end of the audio cable to the Audio1 jack on the projector. Audio1 jack audio cable 2.
Connecting to Video Sources You can connect a DVD player, VCR, camcorder, laser disc player, digital camera, or any other compatible video source to your projector. The projector supports HDTV, NTSC, PAL, and SECAM, and automatically detects the video format. The projector can receive composite video, S-Video, and component video. You can connect one or more of these video sources at the same time. The type of cable you use depends on whether you have composite video, S-Video, or component video.
Connecting the RCA A/V Cable Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Connect the yellow plug on one end of the A/V cable to the projector’s yellow Video jack. 2. Connect the other yellow plug to the video-out jack on your video source. 3. Connect the red and white plugs on the A/V cable to the projector’s Audio L (white) and R (red) jacks. 4.
Connecting an S-Video Cable If your video source has an S-Video jack, you can use it to project a higher quality video image. However, you’ll need an S-Video cable, which may be included with your video source, or can be purchased separately. Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Insert one end of an S-Video cable into the projector’s S-Video connector. 2. Insert the other end into the S-Video output port of your video source. 3.
Connecting a Component Video Cable If your video source has component (blue, green, and red) connectors, you can use them to project a higher quality video image. However, you’ll need a VGA-to-component video cable, which is available from EPSON; see page 8. Before starting, make sure the projector and your DVD player or other video device are turned off. 1. Connect the VGA end of the cable to the projector’s Computer 2/Component Video port. 2.
2 Using the Projector Once you’ve connected the projector to your computer or other equipment (as described in Chapter 1 or Appendix A), you’re ready to turn on the projector, adjust the image, and give your presentation. Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote.
Turning On Your Equipment Make sure your projector and other equipment are set up and connected correctly, as described in Chapter 1 or Appendix A. Then turn on your projector, as described below, followed by any equipment you’ve connected to it. You can turn on your computer and video equipment in any order, but if you have more than one computer or video source connected, you may have to switch to the desired source as described on page 28.
5. Press the red Power button on top of the projector. The power light flashes green as the projector warms up, and the projection lamp comes on in about 30 seconds. The power light stays green, and you may see a blue screen with the No Signal message displayed. This is normal. power light Power button warning 6. Do one of the following: ■ If you’re projecting from a computer, turn on or restart your computer. In a few moments, you should see your computer display projected.
What To Do If You See a Blank Screen If you see a blank screen or a blue screen with the No Signal message after turning on your computer or video source, try the following: ■ Make sure the cables are connected correctly, as described on page 12 (for laptops) or in Appendix A (for other systems). ■ Make sure the power light is green and not flashing and the lens cover is off. ■ Try restarting your computer.
If the Arrange option isn’t available, you may need to select one of the Simulscan resolution settings: 1. Click the Monitor icon. click here select a Simulscan resolution 2. Select a Simulscan resolution as shown. (Allow a few seconds for the projector to sync up after making the selection.) If you’re using a PC laptop: ■ Press the function key that lets you display on an external monitor. It’s often labelled with an icon such as but it may CRT/LCD also be labelled .
Adjusting the Image Once you see your image, you’ll need to make certain adjustments: ■ To focus or zoom your image, see below. ■ If the image is too high or too low, you can reposition it. See page 25. ■ If the image isn’t square, see page 26. ■ If only part of a computer image is displayed, you may need to press the Resize button. See page 27 for more information. ■ If the projected image is flickering or “noisy,” see page 27.
If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the E-Zoom button on the remote control to zoom in on a portion of the image. See page 35 for instructions. Adjusting the Height of Your Image If the image is too low, you can raise it by extending the projector’s foot. 1. Stand behind the projector. Press the foot release button and lift the front of the projector. This unlocks the foot. back adjustable foot foot release button 2.
Adjusting the Image Shape If the projected image isn’t square or has a “keystone” shape, do one or more of the following: ■ If your image looks like or , you’ve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely.
Resizing the Image Some computer images need to be resized to display in the projector’s native resolution. If only part of your computer image is displayed, you can correct it with the Resize button. ■ Press the Resize button on the projector’s control panel (or on the remote control). The screen image is automatically compressed. ■ Continue pressing the Resize button to pan around the screen in the original resolution.
Controlling the Projector While giving your presentation, you may want to switch between picture sources, adjust the volume, or temporarily turn off the picture and sound. Follow the instructions below to access theses features from your projector’s control panel. You can also access these features, plus many others, using the remote control as described in Chapter 3.
Shutting Down the Projector When you’ve finished using the projector, follow the recommended procedure to shut it down. This extends the life of the lamp and protects the projector from possible overheating. 1. If you’ve connected a computer or laptop and it’s displaying only through the projector (the computer’s monitor is disconnected or turned off), shut down the computer first; otherwise you may not be able to see your computer’s display to shut it down properly. 2.
30 Using the Projector
3 Using the Remote Control The remote control lets you access your projector’s features from anywhere in the room—up to 30 feet away. You can use it to turn the projector on and off, zoom in on a portion of your image, and highlight your presentation. If you’re using a computer and you’ve connected the mouse cable (as described in Chapter 1 or Appendix A), you can use the remote control as a wireless mouse.
Turning On and Using the Remote Control caution When replacing batteries, take the following precautions: Don’t mix old and new batteries. ■ Replace batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately. ■ Before using the remote control, you need to install its batteries and turn it on as described below. Installing Batteries Follow these steps to install or replace the batteries: 1.
Using the Remote Control When using the remote control, stand within 30 feet of the projector. Point the remote control either at the front or back of the projector or at the screen (the projector’s front sensor can detect signals bounced off the screen). ■ Press the button for the function you want to use. See the following pages for instructions. ■ For some functions, you need to use the button like a mouse to navigate on the screen.
Adjusting the Volume If you’ve connected an audio source to the projector, you can adjust the sound that’s output through the projector’s speakers. ■ To increase the volume, press on the right side of the Volume button. ■ To reduce the volume, press on the left side of the Volume button. Turning Off the Picture and Sound Power A/V Mute Freeze E-Zoom You can use the A/V Mute button on the remote control to turn off the image and sound and darken your screen.
Zooming Your Image You can zoom in on a portion of the image using the E-Zoom button on the remote control. 1. Press the E-Zoom button. Power A/V Mute Freeze E-Zoom A crosshair indicating the center of the zoom-in area appears on the screen. 2. Use the button to move the crosshair where you want it. 3. Press the right side of the E-Zoom button to enlarge the selected area. ■ Press the button repeatedly to enlarge it up to four times in 25 steps.
Displaying Picture-in-Picture Video You can open a small video window on your computer image, and view a video at the same time as your computer presentation. If you’re using component video, you can display a second video (from a composite or S-video source) in the window. First make sure you have connected your VCR or other video sources as described in Chapter 1. If you’re using S-video, you need to select it in the P in P menu option as described on page 53. 1.
Highlighting Your Presentation You can highlight areas on the screen using the numbered buttons on the remote control. You can use these “special effects” features to annotate your presentation slides or call attention to your most important points. The following three highlighting tools are available: ■ Pointer or cursor stamp (button 1) ■ Spotlight (button 2) ■ Bar (button 3) Power A/V Mute Freeze E-Zoom spotlight pointer You can customize the highlighting tools through the Effect menu.
Spotlighting Your Image With the Spotlight tool, you can highlight part of the screen. 1. To activate the spotlight tool, press button 2 on the remote control. A square spotlight appears on the image. You can continue pressing button 3 to switch between three spotlight sizes. 2. Use the button to move the spotlight where you want it. 3. To remove the spotlight, press Esc. You can change the default size of the spotlight using the Effect menu; see page 50.
Using the Remote Control as a Wireless Mouse When you use the remote control as a wireless mouse, you can control your computer or click through slideshow-style presentations (such as PowerPoint) from up to 30 feet away. This gives you more flexibility, since you won’t need to stand near your computer to change slides, for example.
■ To double-click, press down twice on the left mouse button. ■ To click and drag, press down on the left mouse button and then tilt the button in the direction you want to drag. Power A/V Mute Freeze Previous E-Zoom You can use the up and down arrow buttons on the remote control to move the cursor or move through a PowerPoint presentation. Next 40 ■ Press the down arrow to move forward through a presentation or display the next slide.
4 Fine-tuning the Projector You can use the projector’s on-screen menus to adjust the image, sound, and other features. You can also create your own startup screen, customize the highlighting tools, and find out how long your lamp has been in use.
Using the Projector’s Menu System The eight projector menus let you adjust and customize the projector features from either the control panel or remote control: 42 ■ The Video menu controls the look and quality of the projected image. It lets you adjust the image position and fine-tune settings such as Brightness, Sharpness, and Contrast. ■ The Audio menu controls the volume level, treble, and bass settings.
Changing Menu Settings You can use the buttons on the control panel or remote control to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the control panel or the remote control.
3. When the menu you want is highlighted, press the button on the control panel or the remote control to select it. The highlight moves to the first option for that menu. Sync+ or Sync– button (control panel) or the 4. Use the button (remote control) to scroll through the list of options. (If a computer or video source isn’t connected, certain options may be unavailable.) Tracking– or Tracking+ button (control panel) or 5. Use the the button (remote control) to change the setting for the selected option.
Adjusting the Image The Video menu lets you make adjustments to the projected image. The options available in the menu depend on which source is connected to the projector: standard computer video (analog RGB), DVI computer video (digital RGB), composite or S-Video, component video, or RGB video (standard TV).
Repositioning the Image note Follow these steps to move the image to a different position: If you have repositioned the image or adjusted the sync setting, you can use the button on the control panel or the Auto button on the remote control to restore the default settings. 1. Press the Menu button. You see the menu screen. 2. Press the button to select the Video menu. 3. Press to select the Position option. You see a positioning screen. 4.
■ Tint (NTSC video only) Adjusts the balance of green to magenta in the image. ■ Sharpness Adjusts the sharpness of the image. ■ Color Mode Corrects the vividness of image color.
Saving and Recalling Computer Settings When you are projecting from an analog computer source, you can save and recall settings (resolution, tracking, sync signal, and position) in up to five different combinations. This is useful if you use more than one computer with the projector; you can save the settings for each one and recall them when necessary. Follow these steps to save the projector’s current settings: 1. Press the Menu button to display the Main menu. 2.
Adjusting the Sound You can use the Audio menu to select the audio source or adjust the sound volume or treble/bass balance. 1. Press the Menu button. You see the menu screen. Sync– button (control panel) or the button 2. Use the (remote control) to highlight Audio. You see the following: 3. Press to select the Audio menu. 4.
Customizing the Highlighting Tools The highlighting tools let you add pointers and other types of annotations to your image, as described on pages 37 to 39. You can use the Effect menu to customize these tools and set the pointer speed for highlighting. The Reset option lets you return all the highlighting tools to their default settings. 1. Press the Menu button. You see the main menu. Sync– button (control panel) or the button 2. Use the (remote control) to highlight Effect. You see the Effect menu: 3.
5. When you’re finished customizing the highlighting tools, press Esc. Your selections are saved. Creating Your Own Startup Screen You can transfer any image from your computer or video source to the projector, and then use it as your startup screen. You can also use it as the screen displayed when the projector is not receiving a signal or when you press the A/V Mute button. The image can be a company logo, slogan, photograph, or any other image you want to use.
4. Use the Tracking and Sync buttons (control panel) or the button (remote control) to select the area of the image you want to use. Then press . 5. When you see the message “Do you use this image?” select Yes and press . You see the screen shown at the left. User's Logo Capture Set the zoom rate. zoom rate : 100 :Return :Select 200 300 :Execute 6. Use the Tracking and Sync buttons (control panel) or the button (remote control) to select a zoom rate (display size), and then press . 7.
Customizing Projector Features You can use the Setting menu to disable the projector’s sleep mode, adjust the image shape, and customize several other features. 1. Press the Menu button. Sync– button (control panel) or the button 2. Use the (remote control) to highlight Setting. You see the options and their settings on the right side: 3. Press to select the Setting menu. 4.
■ No-Signal Msg. Selects a screen color or image to display when the projector is not receiving a signal. The logo setting displays an image that you have transferred to the projector (see page 51). ■ Prompt Turns off the identifying text that appears briefly when you switch picture sources. (It’s best to leave this on.) ■ A/V Mute Selects the screen color or image to display when you press the A/V Mute button.
Setting Advanced Features You can use the Advanced menu to configure the projector for rear projection or ceiling mounting, and adjust several other features. 1. Press the Menu button. Sync– button (control panel) or the button 2. Use the (remote control) to highlight Advanced. You see the features and their settings on the right side: 3. Press to select the Advanced menu. 4.
■ Ceiling Turn on when the projector is mounted upside-down from the ceiling. ■ COM Port Switches between serial (RS-232C) and USB communication for programming/projector control. 5. When you’re finished, press Esc or Menu. Viewing Lamp Usage and Other Information Use the About menu to view information about the display settings of your computer and the number of hours the lamp has been used. note 1. Press the Menu button. You see the main menu.
3. If you have changed the lamp, press to select Reset Lamp Timer. Press again, then select Yes when you see the prompt. Press to confirm the reset. 4. When you’re finished, press Esc or Menu. Restoring the Default Settings The Reset All option lets you return all the projector settings to their default values. Select Reset All and press the button on the control panel or remote control to display the confirmation screen. Select Yes to reset all the default settings or No to cancel.
58 Fine-tuning the Projector
5 Maintaining and Transporting the Projector Y our projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lenses whenever you notice dirt or dust on the surface. ■ Use a canister of compressed air to remove dust. ■ To remove dirt or smears on the lenses, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface. Remove the cap before cleaning Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord.
Cleaning and Replacing the Air Filter Clean the air filter on the bottom of the projector after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. To clean the air filter, follow these steps: 1. Turn off the projector, allow it to cool down, and unplug the power cord. 2. Stand the projector on end with the handle on top to keep dust and dirt from falling inside. 3.
4. If you need to replace the filter, press the arrow tab and lift up the filter to remove it. Press the arrow tab 5. To install a new filter, first insert the tabs, then press down until it clicks in place. warning Be extremely careful when removing the lamp module. In the unlikely event that the bulb has ruptured, small glass fragments may be present and should be removed with caution. If your projector is mounted on the ceiling, you should unmount it before accessing the lamp compartment.
Follow these steps to replace the lamp: 1. Turn off the projector, wait for it to cool down (when the light stops flashing), then unplug the power cord. 2. Allow the projector to cool for at least half an hour (if it has been on). warning Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 3. Use a screwdriver to slide the latch and pop open the lamp cover. Then lift up and remove it. 4.
5. Grasp the lamp as shown and pull it straight out. caution Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 6. Gently insert the new lamp. 7. Once the lamp is fully inserted, tighten its screws. 8. To replace the lamp cover, insert the tabs and then snap the cover into place. (The projector won’t come on if the lamp cover is loose.
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menu. 1. Press the Menu button on the control panel or the remote control. You see the main menu. 2. Use the Sync– button (control panel) or the control) to highlight About. button (remote You see the lamp usage hours and other settings. 3. Press to select Reset Lamp Timer. Press prompt: 4. Select Yes, then press again. You see this . 5. When you’re finished, press Esc or Menu.
Transporting the Projector note EPSON shall not be liable for any damages incurred during transportation. The projector contains many glass and precision parts. If you need to transport it, follow these packing guidelines to prevent damage to the projector: ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
6 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue ? Help button on top of the projector or on the remote control. The following choices are available: ■ Help for the image ■ Help for the sound ■ Language selection (Language) Follow these steps to get help: 1. Press the blue ? Help button on the projector or the remote control.
4. Highlight a solution (if this choice is available). Then press the button to select the solution. Press the Esc button if you need to back up. If the solution is to adjust one of the settings, press either Tracking– or Tracking+ button on the projector (or the use the button on the remote control) to adjust it. 5. To exit the Help system, press the blue ? Help button. If none of the suggestions solves your problem, see additional solutions to problems in the following sections.
The power light is flashing orange and you cannot turn on the projector. The lamp is cooling down. Wait until the light turns off and then press the Power button to turn on the projector. The power light does not come on. Make sure the power cord is connected securely both at the power outlet and the projector. If you have just replaced the lamp, make sure the cover is securely fastened. The lamp warning light is red or flashing red. Replace the lamp as described on page 62.
■ If the projector continues to overheat after you clean the air filter, the problem may be caused by damage to the cooling fan or temperature sensor. Contact EPSON for help. Refer to the following table for a complete description of the projector’s status lights and their meaning: Status lights Light Status Description orange The projector is in sleep mode. You can unplug it or press the Power button to turn it on. flashing green The projector is warming up. Wait for the image to appear.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the P power light is green, not flashing, and the lens cap is off. ■ The projector may be in sleep mode. If the P power light is orange, press the Power button to turn the projector on. ■ If the power was switched off and then on again, the projector may still be cooling down. Wait until the power light stops flashing and remains orange; then press the Power button again.
If you’re using a PC laptop: ■ Hold down the Fn key and press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your laptop’s manual or online help for details. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
Only part of the computer image is displayed. ■ Press the Resize button on the remote control. ■ Make sure the image Position setting is correct on the Video menu. See page 46 for more information. ■ Make sure your computer’s resolution setting is correct. Ideally, it should be 1024 × 768 (800p and 810p) or 800 × 600 (600p) to match the projector’s native resolution. If this option isn’t available, select one of the other compatible video formats listed on page 106.
The image contains static or noise. ■ Make sure the Comp1 Input and Comp2/ YCbCr options in the Setting menu are correct. See page 54. ■ If you’re using a computer cable longer than 6 feet (2 meters), or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables away from the power cord as much as possible to prevent interference. ■ The video signal may be split between the computer and the projector.
You see vertical stripes or the image still looks blurry after trying the solutions in the previous section. ■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice one or more vertical stripes or bands, or some of the characters may look heavy or blurred. Press the button on the projector or the Auto button on the remote control. This resets the projector’s tracking and sync settings.
The colors of the image are not right. ■ If you’re displaying a computer image, use the Color Mode option in the projector’s Video menu to adjust the color. If you’re displaying video, adjust the Color, Tint, and Color Mode settings on the Video menu. ■ Try changing the Color Adjustment setting on the Advanced menu. ■ Check your computer display settings to correct the color balance.
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. on/off switch ■ Make sure the remote control is turned on. ■ Make sure you are within 30 feet (9 meters) of the projector, and within range of the projector’s front or back sensor (approximately 30° to left or right and 15° above or below). ■ The remote control batteries may not be installed correctly or may be low on power. To change the batteries, see page 32.
Where To Get Help EPSON provides technical assistance through electronic support services and automated telephone services 24 hours a day, as listed in the following table. Electronic support services Service Access World Wide Web From the Internet, you can reach EPSON’s product support page at http://support.epson.com. After selecting your product, you can access troubleshooting information, download product documentation, and receive technical advice through e-mail.
Before you call, please have the following information ready: ■ Product name (EPSON PowerLite 600p, 800p, or 810p) ■ Product serial number (located on the bottom of the projector) ■ Computer configuration ■ Description of the problem You can purchase screens, carrying cases, or other accessories from EPSON at (800) 873-7766 or by visiting the EPSON Store at www.epsonstore.com (U.S. sales only). In Canada, please call (800) 873-7766 for dealer referral.
A Appendix A: Connecting to Additional Equipment This appendix explains how to connect the projector to a desktop PC or Macintosh, high-end workstation, more than one computer, or a DVI video source. It also provides guidance on setting up the projector in a permanent installation.
Installing the Projector The projector can be installed for four different viewing setups: front projection, ceiling mounting, rear projection onto a semi-transparent screen, or rear/ceiling projection, as shown: front projection rear projection ceiling mounting rear/ceiling projection To project from overhead, you’ll need to select Ceiling in the projector’s Advanced menu. To project from the rear, select Rear Proj. See “Setting Advanced Features” on page 55.
Connecting to an External Audio System The projector’s internal speakers are loud enough for most rooms. However, if your installation requires maximum volume and sound quality, you can connect the projector to external speakers or a public address (PA) system. This disables the projector’s internal speakers. If you’ve connected multiple audio and video sources to the projector, the projector will automatically switch the audio along with the video source whenever you choose a different video source.
Connecting to a PC Desktop Computer You can connect the projector to any IBM-compatible PC. This section includes instructions for the following: ■ Connecting the computer cable ■ Connecting the mouse cable (if you want to use the remote control as a mouse or use USB audio) ■ Connecting the audio cable (if you’ll be projecting with audio) Follow the steps in each section for the cables you need to connect. Before beginning, make sure the projector and computer are turned off.
3. Connect one end of the computer cable to the projector’s Computer2/Component Video port, as shown. Computer2/Component Video Port 4. Connect the other end of the cable to the computer’s video port. 5. Tighten the screws on the connectors.
Connecting the Mouse Cable note If you have a PC with a serial mouse port, you’ll need a serial mouse cable. See your projector dealer to obtain the correct cable. To use the remote control as a mouse, follow the steps below. You’ll use a different mouse cable, depending on whether your computer has a round PS/2 mouse port or a flat USB port. The USB cable also provides audio support.
Connecting the Audio Cable If your presentation includes sound and you want to use the projector’s built-in speakers, you’ll need to connect a stereo, mini-jack audio cable (not included). If you connected the USB cable, you may not need a separate audio cable. 1. Connect one end of the audio cable to the Audio 1 jack on the projector. Audio 1 jack audio cable 2. Connect the other end of the audio cable to the speaker or audio out port on the computer’s sound card.
Connecting to a Desktop Macintosh note Macintosh configurations vary. See your computer manual for the location of the ports needed to connect your projector. Older models may require a Macintosh adapter set, which you may purchase from EPSON; see page 8. You can connect the projector to any desktop Macintosh.
3. Connect one end of the computer cable to the projector’s Computer 2/ Component Video port, as shown. Computer2/Component Video port Macintosh desktop adapter (if needed) 4. Connect the other end of the computer cable to the video port on the Macintosh. If it doesn’t fit, you may have to use a Macintosh desktop adapter, which you can buy from EPSON (see page 8). To use the adapter, remove its cover as shown and set its DIP switches according to the resolution you want to use, such as 16-inch mode.
Connecting the Mouse Cable To use the remote control as a mouse follow the steps below. If the Macintosh has a USB port, you can use the USB mouse cable included with the projector. If it has a round mouse port, you’ll need a Macintosh mouse cable; see your projector dealer for help in obtaining the correct cable. The USB cable also provides audio suport. If your Macintosh supports USB and your presentation includes sound, you can play it through the projector’s speakers by connecting the USB cable. 1.
Connecting the Audio Cable If your presentation includes sound and you want to use the projector’s built-in speakers, you’ll need to connect a stereo, mini-jack audio cable (not included). If you connected the USB cable, you may not need a separate audio cable. 1. Connect one end of the audio cable to the Audio 1 jack on the projector. Audio1 jack audio cable 2. Connect the other end of the audio cable to the speaker or audio out port on the Macintosh.
Connecting to a Second Computer To connect a second computer to the projector, you need to use the projector’s Computer1 port. You’ll need an optional DVI-analog cable, unless the computer supports DVI (Digital Visual Interface) video. 1. Connect one end of the cable to the computer’s video port. 2. Connect the other end to the projector’s Computer1 port as shown. Computer 1 port 3. To display images properly, make sure the Comp1 Input option in the projector’s Setting menu is set correctly.
Connecting to a High-End Workstation There is no across-the-board standard for workstation video output. However, your PowerLite projector is capable of remapping input resolutions up to 1600 × 1200 pixels. Workstations that follow the SXGA standard and use the HD15 (standard VGA) connector won’t need an adapter cable or any special connection device. If your system varies, contact your computer dealer for help in connecting your workstation.
94 Appendix A: Connecting to Additional Equipment
B Appendix B: Notices T his chapter i ncludes safety instructions and other important information about your EPSON PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector.
96 Appendix B: Notices ■ Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector. ■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards. ■ Unplug the projector during lightning storms or when it will not be used for extended periods.
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: ■ There is an object between the remote control IR emitter and the IR receiver on the projector. ■ Ambient light is too bright. ■ Certain types of fluorescent lighting are used. ■ A strong light source shines into the IR receiver.
Declaration of Conformity According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: EPSON AMERICA, INC. 3840 Kilroy Airport Way MS: 6-43 Long Beach, CA 90806-2469 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Warranty Epson America, Inc. Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc.
FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC.
102 Appendix B: Notices
C Appendix C: Technical Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels Diagonal: 0.9 inches (22.9 mm) Lens F=1.74 to 2.06, f=28.3 mm to 37.98 mm Resolution (native format) 800p and 810p: 1024 × 768 pixels (XGA) 600p: 800 × 600 pixels (SVGA) Color reproduction 24 bit, 16.7 million colors Brightness 810p: 2000 lumens (ANSI) 800p: 1500 lumens (ANSI) 600p: 1700 lumens (ANSI) Contrast ratio 400:1 Image size 30 to 300 inches Projection distance 2.
Projection Lamp Type UHE (Ultra High Efficiency) Power consumption 200 W Lamp life About 1500 hours Part number ELPLP15 Remote Control Range 32.8 feet (10 meters) Batteries Alkaline AA (2) Mouse Compatibility Supports PS/2 and USB Dimensions Height 4.1 inches (104 mm) Width 13.7 inches (348 mm) Depth 10.8 inches (274 mm) Weight 9.3 lb (4.2 kg) Electrical 104 Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC, 3.1A 200 to 240 VAC, 1.
Environmental Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (-10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Safety United States FCC Part 15J Class B UL1950 Rev. 3 Canada DOC SOR/88-475 CSA C22.2 No. 950 Rev.
Compatible Video Formats The projector supports NTSC, PAL, and SECAM international video standards, as well as the monitor display formats listed below. To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector; see the following table for compatible formats. As noted below, some images are automatically resized to display in one of the projector’s “native” formats (such as XGA).
Mode SXGA3—75 SXGA3—85 SXGA+60 SXGA+75 SXGA+85 UXGA48i UXGA60 UXGA65 UXGA70 UXGA75 UXGA80 UXGA85 iMAC VGA iMAC SVGA iMAC XGA MAC II 13 MAC16 MAC19 MAC21 TV525i TV625i SDTV525p HDTV750p HDTV1125i NTSC NTSC4.
Computer Video Port Pin Assignments The Computer2/Component Video port is a female video RGB, 15-pin micro-D-style connector. Here are its pin assignments: 108 Pin no.
Index A A/V Mute, 28, 52, 54 A/V Mute button, 28, 34 About menu, 42, 56 to 57, 65 Accessories, 7 to 8, 80 Adobe Acrobat Reader, 3 to 4 Advanced menu, 42, 55 to 56 Air filter, cleaning and replacing, 61 to 62 Anti-theft device, 8, 11 Arrow button, remote control, 40 Aspect ratio, 27, 103 Audio adjusting tone, 49 adjusting volume, 28, 34, 49 connecting desktop, 87, 91 connecting laptop, 14 connecting second computer, 92 menu, 42, 49 outputting to external sound system, 83 problems, troubleshooting, 77 turning
D I Declaration of Conformity, 98 Default settings, restoring, 44, 57 Desktop adapter, Macintosh, 88 to 89 Desktop computer, connecting, 84 to 87, 88 to 91 Digital visual interface, see DVI Distance from projector to screen, 10, 103 Down arrow button, remote control, 40 Drawing on the screen, 37 to 38 DVI (Digital Visual Interface) cable, 7, 8 source, connecting to, 93 iBook, connecting to, 12 iMac, connecting to, 7 Image adjusting, 24 to 27, 45 to 47 capturing and saving in projector, 51 to 52 correctin
M Options for projector, 8 Problems color, 77 image, 72 to 77 remote control, 78 sound, 77 Projection lamp See Lamp Projector carrying case, 8, 66 cleaning, 60 to 62 connections, see Connecting projector distance from screen, 10, 103 feet, adjusting height with, 25 installing, 82 to 83 lamp specifications, 104 options, 8 positioning, 10 to 11 resolution, 1, 103 specifications, 103 to 108 transporting, 66 troubleshooting, 67 to 77 turning off, 29 turning on, 20 to 23 unpacking, 6 to 7 viewing information a
Resizing image, 27, 35 Resolution, 1, 47, 103 S Safety instructions, 95 to 97 specifications, 105 Screen blank, 22 to 23 distance from projector, 10 Screen image See Image Setting menu, 42, 53 to 54 Shift button, 76 Sleep mode, 29, 54 Sound adjusting, 49 See Audio turning off (using A/V Mute), 28 Source, selecting, 28, 33 Speaker, specifications, 103 Speakers, connecting to external, 83 Special effects buttons, 37 to 38 Specifications brightness, 1, 103 dimensions, 104 electrical, 104 environmental, 105 ge
Volume adjusting, 28, 34, 49 button, 28, 34 setting, 49 W Warning lights, 69 to 72 Warranty, 5, 100 to 101 Workstations, connecting projector to, 93 Z Zoom ratio, 103 Zooming image, 24 to 25, 35 Index 113
114 Index
