user manual
Table Of Contents
- EPSON EPL-6200/EPL-6200L
- Contents
- Product Description
- 1.1 Outline
- 1.2 Basic Specifications
- 1.2.1 Process Specifications
- 1.2.2 Printer Basic Specifications
- 1.2.3 Paper Specification
- 1.2.4 Reliability, Durability, Serviceability
- 1.2.5 Operating Conditions (Including Consumables)
- 1.2.6 Storage and Transport of the Printer Main Unit and Optional Products (Consumables Packaged)
- 1.2.7 Electrical Features
- 1.2.8 Compliance with Standards and Regulations
- 1.2.9 Consumable Components
- 1.3 External Appearance and Parts Name
- 1.4 Controller Specification
- 1.5 Control Panel (EPL-6200)
- 1.6 Control Panel (EPL-6200L)
- 1.7 RAM Expansion
- 1.8 System Requirements (Only for EPL-6200L)
- 1.9 Paper Feed Specifications (Only for EPL-6200L)
- 1.10 Notes on Operation
- 1.11 Status Sheet
- 1.12 Ambient Conditions
- 1.13 Differences in Specifications between Intended Markets
- 1.14 Notes on Installation of Optional Units
- Operating Principles
- 2.1 Overview
- 2.2 Description of Mechanisms
- 2.3 Operating Principles of Electric Circuitry
- Troubleshooting
- 3.1 Overview
- 3.2 Troubleshooting When There is Error Display
- 3.2.1 Fuser warming up problem
- 3.2.2 Fan problem
- 3.2.3 Polygon Motor Error
- 3.2.4 Laser problem
- 3.2.5 High voltage circuit problem
- 3.2.6 Fuser high temperature problem
- 3.2.7 CPU Error
- 3.2.8 Engine Communication Error
- 3.2.9 Fuser low temperature problem
- 3.2.10 Standard RAM Error
- 3.2.11 RAM Error (Slot 0)
- 3.2.12 ROM Checksum Error (Font)
- 3.2.13 ROM Checksum Error (Program)
- 3.2.14 Option ROM Error
- 3.2.15 EEPROM Error
- 3.2.16 Engine Initialization Error
- 3.2.17 Other Hardware Error
- 3.2.18 Software Error
- 3.3 Troubleshooting for Paper Jam
- 3.4 Troubleshooting for Abnormal Operations
- 3.5 Troubleshooting for Electrical Parts
- 3.6 Troubleshooting for Print Quality Problems
- Disassembly and Assembly
- Adjustment
- Maintenance
- Appendix
EPSON EPL-6200/EPL-6200L Revision A
Disassembly and Assembly Removal and Installation of Major Components 153
4.5.2 Fuser Unit Disassembly
1.
Remove the Fuser Unit. (p.152)
2. Remove the two screws, and separate the Fuser Unit.
3. Remove the two shaft holders, and remove the Pressure Roller.
4. Remove the one screw, and remove the terminal board.
5. Pull out the Fusing Roller Heater Lamp.
6. Pull off the driving gear from the Fusing Roller.
7. Pull out the Fusing Roller.
8. Remove the four Fusing Separation Claws.
9. Remove the one screw, and remove the Thermistor.
10. Remove the two screws, and remove the Thermostat.
Figure 4-35. Disassembling the Fuser Unit
C A U T I O N
Do not touch the glass of the heater lamp with bare hands.
When you remove the Fusing Separation Claw, take care not to
lose the spring.
To avoid scratching the Fusing Roller surface by the Fusing
Separation Claw, keep the Fusing Separation Claw lifted when
removing or installing the Fusing Roller.
When installing the Thermistor, lead the harness as shown at
right.
Install the Fusing Roller Heater Lamp so that the voltage
indicator faces the gear side.
Install the shaft holder so that the groove in the shaft holder is
put on the rib of the Fuser Unit.