USER’S MANUAL VFD Customer Pole Display 48200530 March 2002, V1.
Preface & Contents This user’s manual illustrated how to install VFD Customer Pole Display and its technical settings. The Customer Pole Displays have integrated type for bundling POS PC system and stand alone type as well, the ideal products for Point-Of-Sale solutions. FCC Notice Federal Communications Commission (FCC) Radio Frequency Interference Statement This device complies with part 15 of the FCC Rules.
Contents 1. FEATURES ...................................................................................................................... 1 2. GENERAL SPECIFICATION ................................................................................... 2 3 UNPACKING AND CHECKING THE PARTS ..................................................... 3 3.1 VFD POLE DISPLAY FOR 720/750 M ONITOR ..........................................3 3..4. POLE DISPLAY FOR 800cx SERIES..............................................
7. COMMAND...................................................................................................................27 7.1. POS7300 SERIES COMMAND SET ...........................................................................27 7.2 CD5220 STANDARD M ODE COMMAND LIST ........................................................28 7.3 UTC STANDARD MODE COMMAND LIST .................................................................32 7.4 UTC ENHANCED MODE COMMAND LIST ......................................
9.22 RESET USER DEFINED CHARACTER SET ................................................................47 9.23 CANCEL USER DEFINED CHARACTERS..................................................................47 9.24 STORE THE USER DEFINED CHARACTER INTO EEPROM ...................................47 9.25 RESTORE THE USER DEFINED CHARACTER FROM EEPROM .............................48 9.26 CHARACTER FONT FORMAT ....................................................................................48 10.
1. Features (1) Data can be display on 20 columns x 2 lines. (2) Blue– green color and large character are easy to see (3)The DIP switches setting emulate commands mode, baud rate and international character. (4) Command emulation modes include POS7300/ CD5220 II/ ADM787/ UTC / AEDEX/ Epson/ DSP800. (5) User’s-defined character and message can be downloaded. (6) Display area can be controlled by window function. (7) Provides an interface based in RS-232C, and RS232C baud rate from 4800 to 38400 bps.
2.
3 Unpacking and Checking the Parts Please make sure following parts are found in the customer display box. 3.1 VFD Pole Display for 720/750 Monitor VFD Pole Display For 720/750 Monitor Figure :720 with 300dx PC and Pole Display The parts of the Pole Display kits: (Part no.
3..4. Pole Display for 800cx Series VFD Pole Display for 800cx series The parts of pole display kits: (Part no. P07308) (1) Pole Display Module (2) Flat Cable (RJ-45 to DB-9F flat cable connector) (3) Installation Guide (4) Two pieces of pole support (22cm x 1, 9cm x 1) (5) Pole Display cover kit Flat Type VFD Customer Display for 800cx The parts of pole display kits: (Part no.
3. 5 Stand Alo ne VFD Pole Display 225 mm The parts of pole display kits : (Part no.P07303 ) (1) Pole Display Module (2) Flat Cable (DB-9P to DB -9P flat cable connector) (3) Base Unit (4) Two pieces of pole support (1x22cm, 1x9cm) (5) User’s manual (6) Power Adapter 7 191 mm 93 mm 281 mm 501 mm Stand Alone VFD Customer Pole Display (Part no.
P 720 Mo nitor P 300dx PC 8
Set jumpers on 300dx mainboard COM1 JP4 COM2 JP3 COM3 JP9 COM4 JP5 1-2 (Default) 3-4 5-6 1-2(Default) 3-4 5-6 1-2(Default) 3-4 5-6 1-2(Default) 3-4 9 Data Line +5V +12V Data Line +5V +12V Data Line +5V +12V Data Line +5V
4.4. VFD Pole Display for 800cx series 1.Connect flat cable DB -9P end connector to 800cx serial port COM4. If COM 4 has been used by other device, please use COM1, COM2, or COM3 serial port. COM4 Figure: 800cx rear view 2. Pole Display Jumper setting (on the base of 800cx terminal ) (1).Set JP2 com4 port Pin 1-2 at +12V or Pin 7-8 at +12V. (2).If com4 has been used, select com1, com2, or com3 for Pole Display. (3).Below is the jumper setting label on the base of 800cx terminal.
4. 5 Stand Alone VFD Pole Display 4.5.1. Specifications Data transmission: Synchronization: Handshaking: Serial Asynchronous DTR / DSR MARK = -3 to –15 V (logic “1”) SPACE = +3 to +15 V (logic “0”) 4800,9600,19200,38400 bps None, even 8 bits 1 or more Signal level: Baud rates: Parity: Bit length: Stop bits: 4.5.2.
4.5.3. Interface Below illustrate the configuration of Stand Alone VFD Pole Display base. Figure of Stand Alone Pole Display Base Interface connector on the bottom of Pole Display Base (standard ) CN2 CN3 CN6 CN2: RS-232C connects to PC/Host CN3: Connect to display panel CN6: Power supply connector CN1,CN4, CN5: No used Power Supply Connectors CN6 / Connector type: DC jack (5.5/2.
Pin assignment No + - Signal Vin GND RS232C link to PC/HOST connector CN2 / Connector type: D-sub 9 pin female Pin assignment No 2 3 4 5 6 8 Signal RXD TXD DSR GND DSR DSR Direction From PC/Host to display From printer to PC/Host From PC/Host to printer From display to PC/Host From display to PC/Host Function description Receive data Printer status data PC/Host ready signal Signal ground Display/printer ready signal Display/printer ready signal RS232C link to printer connector CN1 / Connector type: P
5. Dip Switch and Software Setting 5.1 Command type selection SW1 ON OFF ON OFF ON OFF ON OFF SW2 ON ON OFF OFF ON ON OFF OFF SW3 ON ON ON ON OFF OFF OFF OFF Command type POS7300 ESC/POS ADM 787 DSP800 AEDEX UTC/P UTC/S CD5220 5.2 Baud rate selection SW8 ON OFF ON OFF SW9 ON ON OFF OFF Baud rate (bps) 4800 9600 19200 38400 Default * 5.3 Parity check selection SW10 ON OFF Parity check None-parity Even-parity Default * 5.
5.4 International character set SW4 SW5 SW6 SW7 Character set Code table ( 80H-FFH) ON ON ON ON *default U.S.A. PC-437(USA, standard Europe) OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF FRANCE PC-850(multilingual) GERMANY PC-850(multilingual) U.K.
5.6. Software Status Setting When system POWER ON, there is no need to turn off to modify Command Type, Baud Rate, Parity, Demo Mode and International Character. To re-set DIP Switch to various Command Type under the following list of Command to modify the setting. The setup value will be stored in the EEPROM. When DIP Switch is OFF. Next time the system POWER ON previous setup value will be the default value and no need to modify. 5.6.1.
5.6.3 Command type select STX 05 C n ETX /Change command type/ ASCII Format STX 05 C n ETX Dec. Format [02][05][67] n [03] Hex. Format [02h][05h][43h] n [03h] 30h n 37h Description This command will change the command type and initialize the display. The display emulation mode is based on DSP800/ESC/ADM787/POS7301/AEDEX/UTC/C D5220 mode. The setting function will be saved to EEPROM.
5.6.5 Save data for demo display STX 05 L n m ETX /Save demo message to EEPROM/ ASCII Format STX 05 L n m ETX Dec. Format [02][05][76] n m [03] Hex. Format [02h][05h][4Ch] n m [03h] Description Save demo message for upper line and bottom line n = 31h save data message for upper line n = 32h save data message for lower line m=data message ; the maximum data character is under 200 5.6.6 Run Demo message STX 05 L n m ETX /Run demo message/ ASCII Format STX 05 D 08 ETX Dec. Format [02][05][68][08][03] Hex.
5.6.7 Set Communication parity STX 05 P n ETX /Parity check selection/ ASCII Format STX 05 P n ETX Dec. Format [02][05][80] n [03] Hex. Format [02h][05h][50h] n [03h] n=30h,31h Description Change the display communication parity. Set 8 data bit and the parity set for even or non-parity. N 30h 31h Parity check None-parity Even-parity 5.6.8 Show VFD Firmware Version STX 05 V 01 ETX /Show VFD Firmware Version/ ASCII Format STX 05 V 01 ETX Dec. Format [02][05][86][01][03] Hex.
6.
Change to UTC enhanced mode Change to UTC standard mode O O Write string to upper line O O O O Write string to lower line Upper line message scroll continuously Bottom line message scroll continuously Message vertical down scroll continuously Message vertical upper scroll continuously O O O O O O O O Carriage return O O Line feed O O Back space O O Horizontal tab O Command type select O O O O O O O 25 O
Table-2 J2 PARTNER EPSON GIGA POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800 Upper line message scroll once pass O O Change attention code O O Two line display Clear upper line and move cursor to upper left-end position Clear bottom line and move cursor to bottom left-end position Set period to upper line, last n position O O O O O Set line blinking, upper line O O Clear line blinking, upper line Clear field 1 and move cursor to field 1, first position Clear field 2 and move cursor to field
7. Command 7.1. POS7300 series command set POS7300 Standard Mode Command List Command ESC F A .. CR ESC F B .. CR ESC F D .. CR ESC F O ..
7.2 CD5220 Standard Mode Command List Command ESC DC1 US SOH ESC DC2 US STX ESC DC3 US ETX ESC Q A .. CR Code (hex) 1B 11 1F 01 1B 12 1F 02 1B 13 1F 03 1B 51 41 [n]x20 0D ESC Q B .. CR 1B 51 42 [n]x20 0D ESC Q D ..
upper left-end position.
CD5220 Standard Mode Command List-2 Command ESC I x y CLR Code (hex) 1B 6C x y / 1F 24 x y 1x20, y=1,2 1F 24 x y 1x20,y=1,2 1B 40 1B 57 1 x1 x2 y 1x1x2 20 y=1,2 0C CAN 18 ESC * n US X n ESC & s n m [a (P1…Pa)]x (m -n+1) ESC ? n ESC % n 1B 2A n 1n 4 1F 58 n 1n 4 1B 26 1 n m [a(p1…pa)]x (m-n+1) 20 n m FF 1B 3F n n=20h~7Fh Deletes download characters. 1B 25 n n=00,01 Select/cancel download character set.
*2: The parameter of international fonts set control by command “ESC f n” Parameter ‘A’ ‘G’ ’I’ ‘J’ ‘U’ ‘F’ ‘S’ ‘N’ ‘W’ ‘D’ ‘E’ ‘L’ ‘R’ n International Font Set U.S.A. Germany Italy Japan U.K.
7.3 UTC standard mode command list Command BS HT LF CR DLE DC1 Code (hex) 08 09 0A 0D 10 n 0 n 28h 11 Function description Back space Horizontal tab Line feed Carriage return Display position Over write display mode DC2 DC3 DC4 US ESC d 12 13 14 1F 1B 64 Vertical scroll mode Cursor on Cursor off Clear display Change to UTC enhanced mode 7.4 UTC enhanced mode command list Command ESC u A .. CR ESC u B .. CR ESC u D ..
7.5 AEDEX mode command list Command ! # 1 … CR ! # 2 … CR ! # 4 … CR ! # 5 … CR ! # 8 … CR ! # 9 … CR ! # 6 … CR Code (hex) 21 23 31 [data x 40] 0D 21 23 32 [data x 40] 0D 21 23 34 [data x 40] 0D 21 23 35 h h ':' m m 0D h, m='0'-'9' 21 23 38 n m 0D 20H,n, m 21 23 39 [data x 40] 0D 21 23 36 [data x 40] 0D Function description Upper line display Bottom line display Upper line message scroll Display time Change attention code Two line display Upper line message scroll once pass 7.
7.
7.8 EPSON ESC/POS command list EPSON ESC/POS command list-1 Command Code (hex) HT 09 BS 08 US LF 1F 0A LF 0A US CR 1F 0D CR 0D HOM 0B US B 1F 42 US $ x y 1F 24 x y (x=1~20, y=01,02) CLR 0C US X n 1F 58 n (01 n 04) US E n 1F 45 n (n=00~ffh) ESC @ 1B 40 ESC t n 1B 74 n (n=00-0fh) ESC R n 1B 52 n (n=00-0fh) US r n 1F 72 n (n=00,01) US MD1 1F 01 US MD2 1F 02 US MD3 1F 03 ESC & s n m 1B 26 1 n m [a(p1..pa)]x [a(p1..
EPSON Esc/pos command list Command Code (hex) ESC W n s x1 y1 x2 y2 1 B 57 n s x1 y1 x2 y2 n=1,2,3,4 s=0,1 ESC = n US : 1B 3D n n=1,31,select printer n=2,32,select display n=3,33, select printer, display 1F 3A US ^ n m 1F 5E n m 00 (n, m) ff n=Word time m=show string time US @ US T h m US U ESC s 1 1F 40 1F 54 h m 0<=h<=17h, 0<=m<=3bh 1F 55 1B 73 01 ESC d 1 1B 64 01 Function description Specify/cancel the window range. 1<=x1<=x2<=20 1<=y1<=y2<=2 Select peripheral device.
Set international font for ESC/POS (Table 7-11) n 0 1 2 3 4 5 6 International font set U.S.A FRANCE GERMANY U.K. DENMARK I SWEDEN ITALY n 7 8 9 10 11 12 15 International font set SPAIN JAPAN NORWAY DENMARK II SLAVONIC RUSSIA Reserved Select code for ESC/POS (Table 7-12) n 0 1 2 3 4 5 6 7 International font set (80H~FFH) Page 0, (PC437: U.S.A.
8. Character Set 8.1 International Character Sets ASCII Code Country Hex 23 Dec 35 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E 36 64 91 92 93 94 96 123 124 125 126 U.S.A # $ @ [ \ ] ^ ` { | } ~ France # $ à ° ç § ` é ù è ¨ Germany # $ § Ä Ö Ü ` ä ö ü â U.
8.2 USA, Standard Character Sets (20H – 7EH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 20H SP ! “ # $ % & ‘ ( ) ς + , - . / 30H 0 1 2 3 4 5 6 7 8 9 : ; < = > ? 40H @ A B C D E F G H I J K L M N O 50H P Q R S T U V W X Y Z [ \ ] ^ _ 60H ` a b c d e f g h i j k l m n o 70H p q r s t u v w x y Z { | } ~ SP 8.
8.4 Page 1 (Katakana) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H á â ã 90H f § IE A0H SP ç è IR ë ì ð ñ ó ô -1 ² ³ x ½ 1 Ô / ± B0H C0H D0H " E0H « F0H » ~ 8.
8.6 Page 3 (PC860: Portuguese) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ã à Á ç ê Ê è Í Ô ì Ã Â 90H É À È ô õ ò Ú ù Ì Õ Ü ¢ £ Ù Pt Ó A0H á í ó ú ñ Ñ a o ¿ Ò ¬ ½ ¼ ¡ « » á â Ã ð Ó ó ì ô Ô è Ù ä B0H C0H D0H E0H F0H ± ÷ ø n ° ² SP 8.
8.8 Page 5 (PC865: Nordic) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ä à å ç ê ë è ï î ì Ä Å 90H É æ Æ ô ö ò û ù ÿ Ö Ü ø £ Ø Pt ƒ A0H á í ó ú ñ Ñ a o ¿ ¬ ½ ¼ ¡ « ¤ á â Ã ð Ó ó ì ô Ô Ù ä B0H C0H D0H E0H F0H ± ÷ è ° ø n · ² SP 8.
8.
9.Command details 9.1 Overwrite mode In this mode, the cursor will move rightward and begin from the upper left-end position. When the cursor reached the end of the upper line, the cursor will move down to the bottom left-end position to continue. When the cursor reached the end of the bottom line, it will move up the upper left-end position and overwrite the previous characters. 9.2 Vertical scroll mode In this mode, the cursor will move rightward.
9.6 Move cursor left When the current cursor is at the left-end position, this command operates differently depends on the display mode. Overwrite mode: When the cursor reached the left-end of the lower line, it will continue to the right-end of the upper line, overwrite previous characters. When it reached the left end of the upper line, it will continue to the right-end of the lower line.
the same position. Horizontal scroll mode: The cursor will remain stationary. 9.10 Move cursor to home position The cursor will move to the left-end position of the upper line 9.11 Move cursor to left-most position The cursor will be moved to the left-end position of the current line. 9.12 Move cursor to right-most position The cursor will be moved to the right-end position of the current line. 9.13 Move cursor to bottom position The cursor will be moved to the right-end position on the lower line. 9.
9.18 Clear current line, and cancel string mode The current line is cleared, and the string mode is cancelled. 9.19 Brightness adjustment Adjust the brightness of the vacuum fluorescent display. When n=3,brightness=70% When n=4,brightness=100% 9.20 Set cursor ON or OFF When n=0, cursor is OFF When n=1, cursor is ON 9.21 Set user-defined characters The n defines the beginning character code, and m defines the ending character code. When only one character is defined, use n=m.
9.25 Restore the user defined character from EEPROM If EEPROM is not supported, this command is ignored. 9.26 Character font format One font consists of 5 bytes’ string.
10.
