SERVICE MANUAL Copy Server EPSON Color Copy Station 8200 ® SEOT99005
Notice o All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic, mechanical, photocopying, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. o All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.
PRECAUTIONS Precautionary notations throughout the text are categorized relative to 1)Personal injury and 2) damage to equipment. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by DANGER Headings. WARNING Signals a precaution which, if ignored, could result in damage to equipment.
About This Manual This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of EPSON Color Copy Station 8200. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. Contents Symbols Used in This Manual This manual consists of six chapters and Appendix. CHAPTER 1.
Revision Status Revision Rev.
EPSON Color Copy Station 8200 Revision A Product Description Outline .......................................................................................................... Features ................................................................................................... System Diagram ....................................................................................... About EPL-C8200 ....................................................................................
EPSON Color Copy Station 8200 Revision A Mother Board Jumper Setting ................................................................ 55 Adjustment Adjustment ................................................................................................. 57 Hardware Check ..................................................................................... 57 LCD Panel Check ............................................................................... 57 ISA Board Check ..............................
CHAPTER 1 PRODUCT DESCRIPTION
EPSON Color Copy Station 8200 Revision A n 8 Job memories to save user-defined copy parameters 1.1 Outline n Standard copy protection for bills The Color Copy Station 8200 can be connected to EPSON scanner and EPSON color laser printer. It works not only as a stand-alone copier also as network scanner adapter. Further more, it offers some web-based functions to confirm the status of the system, to set the initial parameters, and to update the system firmware.
EPSON Color Copy Station 8200 Revision A 1.1.2 System Diagram 1.1.3 About EPL-C8200 Figure 1-2 shows the color copy system diagram. The 100 base-TX environment is recommended for using Network TWAIN on the Client PC, because the very large amount of data flows on the network and the traffic increases. Though EPL-C8200 has 64Mbyte memories as a default, the minimum size of memories required for Color Copy System is 160MB.
EPSON Color Copy Station 8200 Revision A 1.2 Basic Specifications 1.2.3 Safety, EMC 1.2.1 Local Copy Speed THROUGH PUT Table 1-1.
EPSON Color Copy Station 8200 Revision A n Humidity 1.2.9 Interfaces 10 ~ 90%, no condensation 1.2.9.1 SCSI n Vibration o Connector 1.0G D-Sub 50 pin half pitch (based on ANSI X3. 131-1986) 1.2.7 Reliability o Signals o MTBF Table 1-2. Connector Pin Alignment 10000 hours (not including the EL intensity loss) Pin number Signal name Pin Number Signal name 1 GND 26 DB0 2 GND 27 DB1 1.2.
EPSON Color Copy Station 8200 Revision A Table 1-2. Connector Pin Alignment Table 1-3. Connector Pin Alignment Pin number Signal name Pin Number Signal name Pin number Signal name Pin Number Signal name 20 GND 45 RST 11 BUSY 24 GND 21 GND 46 MSG 12 ERROR 25 GND 22 GND 47 SEL 13 SELECT - - 23 GND 48 C/D o Cable 24 GND 49 REQ 25 GND 50 I/O PRCB4N (recommended) 1.2.9.
EPSON Color Copy Station 8200 Revision A 1.3 Functions Table 1-4.
EPSON Color Copy Station 8200 Revision A AVAILABLE COMBINATION OF EACH FUNCTION Table 1-8. Scanner and Printer Option Table 1-6.
EPSON Color Copy Station 8200 Revision A 1.3.2 Local Copy A3W, Ledger, A3, B4, Legal, Letter (portrait), Letter (landscape), A4 (portrait), A4 (landscape), B5 (portrait), B5 (landscape), Executive (portrait), Executive (landscape) OPERATIONAL PRINCIPLE Local copy function is responsible for the image data scanned by GT-1000 to be processed by CCS 8200 and sent to the printer. Before starting copy, user can set some parameters, number of copy, brightness, contrast and so on, on the control panel.
EPSON Color Copy Station 8200 a1 b Revision A ZOOM a2 Table 1-10. User-defined and Pre-set Zoom Zoom User-Setting Ratio (%) Remarks User-defined Zoom - 25-400 in increments of 1% Pre-set Zoom LedgeràLetter 64 A3àA4/B4àB5 70 11x15àLetter 78 LegalàLetter 78 B4àA4 81 A3àB4/A4àB5 86 100% 100 B4àA3/B5àA4 115 LegalàLetter 121 A4àB4 122 LetteràLedger 129 A4àA3/B5àB4 141 5.5x8.5àLegal 154 c1 d c2 Paper Size Printing guaranteed area Figure 1-4.
EPSON Color Copy Station 8200 Revision A For all pre-set zoom, user can select just-fitting copy option by touching the just-fitting button on the control panel. When the just-fitting is valid, whole area of the document (including non-printed area) is scanned and the area is printed so that it is put in the print guaranteed area. Document (Scanner) MULTIPLE COPIES o Setting Range: 1-99 (default: 1) Scanning is done only one time. The multiple copy function is accomplished by printer’s copy function.
EPSON Color Copy Station 8200 Revision A SPLIT COPY This function enables to copy individual pages for opened-booklet located on the flat-bed. There are limitations as follows such as paper size must be one of A4, B5, Letter, and Executive. The combinations of copy parameters other than the following are not allowed and not supported by ADF either. Table 1-11.
EPSON Color Copy Station 8200 Revision A INTERNAL PROCESSING Table 1-12.
EPSON Color Copy Station 8200 Revision A Table 1-12.
EPSON Color Copy Station 8200 Revision A Table 1-14. Job Memory COPY ADJUSTMENT MODE Table 1-13. Copy Adjustment Mode RGB Adjustmen t Saturation Color / B/W Brightness Color ±3 step ±3 step ±3 step ±3 step ±3 step B/W ±3 step ±3 step N/A N/A N/A Contrast Hue Default value of each parameter is zero. (Center Value) JOB MEMORY CCS 8200 has 8 job memories to save some copy parameters. Parameters can be saved are as follows. Table 1-14.
EPSON Color Copy Station 8200 Revision A Table 1-15. Status Items Printer Scanner PRINTER CONTROL Status display Status print Model Name A A Current status A NA Tray 1 paper size A A Tray 2 paper size A A Tray 3 paper size A A Tray 4 paper size A A Toner Balance A Oil Roll Balance The maximum memories which can be allotted to the printer is 256MB and it is not enough to print some combinations of paper size and copy mode.
EPSON Color Copy Station 8200 Revision A 1.3.3 Network TWAIN Table 1-16.
EPSON Color Copy Station 8200 Revision A PROTOCOL 1.3.4 Web Status EPSON original protocol on TCP/IP (Peer to Peer connection) OPERATIONAL PRINCIPLES CLIENT OS Web Status functions is the one of three web-based utilities. Web Status module is JAVA applet written by JAVA language and works on the web master. When the user starts WebStatus, browser accesses to CCS 8200, loads WebStatus applet, and executes it.
EPSON Color Copy Station 8200 Revision A CLIENT OS STATUS ITEMS Table 1-20. Status Items Table 1-18. Client OS Software Name EPSON TWAIN Pro Network Items Client OS PC/AT Compatible machine CCS 8200 Windows95, Widows98 WindowsNT3.51 Workstation WindowsNT4.0 Workstation Remarks Registered Name Name registered by WebAdmin Division Division registered by WebAdmin IP address URL Current Status Printer http:///WebStatus.
EPSON Color Copy Station 8200 Revision A STATUS UPDATE TIMING 1.3.5 Web Admin The status displayed on Web Status is updated at the timing below. (Web Status doesn’t get the status from CCS 8200 periodically by itself) OPERATIONAL PRINCIPLES n When Web Status starts n When user clicks the icon of registered CCS 8200 on the WebStatus n When user press the re-load button on the web browser Web Admin function is the one of three web-based utilities for administrator.
EPSON Color Copy Station 8200 Revision A CLIENT OS LOCALIZATION Table 1-21. Client OS Software Name EPSON TWAIN Pro Network Client OS PC/AT Compatible machine Windows95, Widows98 WindowsNT4.0 Workstation Web Admin detects the language used on OS, and uses it for German, French, Spanish, Italian, and Portuguese. For the other languages, WebAdmin uses English. Table 1-22. Localization Client PC OS Localization WebAdmin Localization German German URL French French http:///WebStatus.
EPSON Color Copy Station 8200 Revision A 1.3.6 Web Upgrade Table 1-23.
EPSON Color Copy Station 8200 Revision A 1.3.8 User Settings CLIENT OS 1.3.8.1 User Settings on the Operational Panel Table 1-24. Client OS Software Name EPSON TWAIN Pro Network Client OS PC/AT Compatible machine HOW TO MOVE TO USER SETTING MODE Windows95, Widows98 WindowsNT4.0 Workstation To enter the user setting mode, turn on the power switch while holding down “start” and “stop” key on the operational panel simultaneously. URL ITEMS http:///WebStatus.
EPSON Color Copy Station 8200 Revision A Table 1-25. Language Selection Table 1-26. Control Panel (No 1) Language Control Panel Web Status Web Admina Web Upgrade German German German English Spain Spain Spain English Portuguese Portuguese Portuguese English a. These three web utilities detect OS language by itself and changes its language to be used for user interface. For CCS 8200 the languages which are not shown in the upper table, English is selected.
EPSON Color Copy Station 8200 Revision A 1.3.9 Machine Functions Table 1-28. Web Admin Parameters Initial Value Registered Machine clear for all registered machines Output Tray Face Up Print Margin 0mm for Upper, Left, Right margin Server Scan Enable / Disable disable 1.3.9.1 H/W Check This function is used for manufacture and field supporter. o How to enter this mode To enter user setting mode, turn on the power switch while holding down “0”, “.
EPSON Color Copy Station 8200 Revision A o Available functions 3. The LED lamp on the Control Panel turns on according to the sequence below. n Local Copy Table 1-30. Sequence turn on the LED n Network TWAIN n WebStatus LED (WebAdmin and WebUpgrade can not be used in this mode.) Power ON 1.3.9.3 Firmware Update by Board to Board Copy CCS 8200 supports two ways to upgrade the firmware, one is by WebUpgrade, and the other is by Board to Board copy.
EPSON Color Copy Station 8200 Revision A 1.4 Appearance Table 1-32. Parts List Name 1.4.1 Main Unit Remarks Printer interface connector Scanner interface connector Power Switch Network interface connector Control Panel Interface connector Power Connector 1.4.2 Control Panel Card Slot 3 (ECP Board) Card Slot 4 (SCSI Board) F H G I All Color Card Slot 5 (Network Board) Doc Type Zoom Paper Size Card Slot 6 (ISA Target Board) 2 3 4 5 6 7 8 9 0 .
EPSON Color Copy Station 8200 Revision A 1.5 Accessories (C) Power lump (Green) ON: means CCS 8200 is powered on. OFF: means CCS 8200 is powered of. 1.5.1 Product Component (D) Intensity Adjustment volume A volume switch to adjust LCD intensity. The typical configuration contains the following components. (E) Ten key There are keys to set copy numbers, zoom, and so on. “C” key is used to clear copy numbers and so on for default.
EPSON Color Copy Station 8200 Revision A 1.6 Attention for forgery EPSON Color Copy Station 8200 is a Color Copier, and user can copy all kind of documents. But the administrator must forbid all users from copying bills, securities and so on which are inhibited by law. The system administrator has duty not to make illegal copies.
CHAPTER 2 OPERATING PRINCIPLES
EPSON Color Copy Station 8200 Revision A 2.1.2 Control Circuit 2.1 Operating Principles This section explains the operating principles of CCS 8200. Refer to each Service Manual for the operating principles of printer and scanner. Hardware architecture of this product is PC/AT personal computer, and interfaces of ISA and PCI for extension exist respectively. CPU adopts AMD K6-2 processor, which is driven by 300 MHz Clock, and has one 32MB RAM-DIMM on the mother board.
EPSON Color Copy Station 8200 Revision A o ASIC E02A27: Controls I/F of ISA board and ROM (to start the system), LCD of the control panel (panel module), and the touch panel and control bottom on the LCD. 2.1.3.1 ECP Board ECP Board (Image Processing Board, C850101/F-B) connects to the mother board through the PCI bus of Color Copy Station 8200. o Flash-ROM: Stores firmware, table etc. PCI bus TO update firmware, connect the master ISA board to an open ISA slot.
EPSON Color Copy Station 8200 Revision A FUNCTIONAL EXPLANATION GENERAL DESCRIPTION OF THE BOARD FUNCTION o The board processes image data sent through PCI bus, and stores the image processed data to the SRAM (total memory: 1Mbit) mounted on the board. (DMA IN) o The board sends on the image processed data to the printer through Super I/O.
CHAPTER 3 TROUBLE SHOOTING
EPSON Color Copy Station 8200 Revision A 3.1 Error Message Table 3-1. Alert Message Color Copy Station 8200 is equipped with a self-error-detection function, and when an error occurs, it is indicated by LCD on the control panel or an error lamp. 3.1.
EPSON Color Copy Station 8200 Revision A Table 3-3. Unrecoverable Error Message Table 3-2. Auto Recovery Error Message Cause Copy Server Panel Screen Printer Panel Screen During the printing procedure, the print data were too complex for image processing to keep up with the printer engine speed. Printer Error Printer Overrun After Error Recovery Job will Continue Memory was insufficient for a processing task, and operation cannot continue.
EPSON Color Copy Station 8200 Revision A Table 3-3. Unrecoverable Error Message Cause Copy Server Panel Screen The paper output cover is open. Printer Error Cover Open After Error Recovery Job will Continue Exit Cover Open Continue The Fuser cover is open. Printer Error Fuser Unit Open After Error Recovery Job will Continue Fuser Unit Open Continue Printer Error Paper Unit Open After Error Recovery Job will Continue Paper Unit Open The paper feed unit is open.
EPSON Color Copy Station 8200 Revision A Table 3-3. Unrecoverable Error Message Cause Copy Server Panel Screen The PostScript card that cannot be used with this printer is inserted. Printer Error Post Script Error After Error Recovery Press the Stop button HDD is in trouble.
EPSON Color Copy Station 8200 Revision A Table 3-4. Details of Service Call Error Error Category e Error Code ffff C 0090 C Table 3-4.
EPSON Color Copy Station 8200 Revision A Table 3-5. Other Error Message Cause Copy Server Panel Screen Copy Activity Network Communication is error Printer Error Communication Error After Error Recovery Press the Stop button Cancel Printer is off-line Printer Error Off-line After Error Recovery Job will Continue Continue Printer is used by other AUX I/F or printer is resetting. Printer Error Printer Busy Press the Stop button Cancel Printer model is not right.
EPSON Color Copy Station 8200 Revision A 3.1.2 Scanner Error of Local Copy Mode 3.1.3 Network TWAIN Error Table 3-6. Scanner Error of Local Copy Mode Table 3-7. Network TWAIN Error Cause Copy Server Panel Screen Scanner is not connected. Scanner Error Communication Error Impossible After Error Recovery Press the Stop button Scanner ADF is in trouble. Scanner Error ADF Error Impossible After Error Recovery Press the Stop button A paper occurred at the ADF. Scanner cover is open.
CHAPTER 4 DISASSEMBLY AND ASSEMBLY
EPSON Color Copy Station 8200 Revision A 4.1 Overview 4.1.2 Tools This section describes procedures for disassembling the main components of Color Copy Station 8200. Unless otherwise specified, disassembly units or components can be reassembled by reversing disassembly procedure. Precautions for any disassembly or assembly procedures re described under the heading “CAUTION” or “WARNING”. Any adjustments required after disassembling the units are described under the heading “Required Adjustment”.
EPSON Color Copy Station 8200 Revision A 4.2 Disassembly and Assembly 4.2.2 Optional Board Removal This section explains disassembling procedure. 4.2.2.1 ISA Board Removal 1. Remove the upper case. (“Upper Case Removal” on page 46) C A U T IO N See “Precaution” on page -34 before starting disassembly and assembly procedures. 3.
EPSON Color Copy Station 8200 Revision A 4.2.2.2 SCSI Board Removal Table 4-2. PCI/ISA Slot, installing board Installing Board 1. Remove the upper case. (See “Upper Case Removal” on page 46) Slot Type PCI1 PCI ECP Board (for printer interface) PCI2 PCI SCSI Board (for scanner interface) PCI3 PCI Network Board 3. Remove SCSI board from the slot (PCI2) of the mother board. (See “ISA Board Removal” on page 46) PCI4/SLOT1 PCI/ISA ISA Board 4.
EPSON Color Copy Station 8200 Revision A 4.2.3 Power Supply Unit Removal 4.2.4 Mother Board Removal 1. Remove the upper case. (See “Upper Case Removal” on page 46) 1. Remove the upper case. (See “Upper Case Removal” on page 46) 2. Remove 4 screws (SMH/W6# X 6N) securing the power supply unit to the body case, and pull out the power supply unit toward back of the CCS 8200 until its stoppers touches the body case. 2. Remove the optional board (ISA / SCSI / Network / ECP Board).
EPSON Color Copy Station 8200 Revision A 4.2.5 Panel Board Removal 1. Remove the harness (control panel cable) from the CCS 8200. C A U T IO N 2. Remove 8 CPB screws (3x12) securing the upper panel case and lower panel case. Then remove the lower panel case. C P B (3x8) C P B (3x8) When tightening screws, use a hand in order to avoid loosen screws. Do not use motor driver. n When installing the panel board to the upper panel case, electrolytic condensers on the board may touch the upper panel case.
EPSON Color Copy Station 8200 Revision A 4.3 Firmware Version-Up Control program, each application, and tables for image processing are stored in the Flash ROM mounted on the ISA board. Therefore, in case of firmware version-up, it is necessary to re-install the program by transferring the firmware form the Master Board to the target board (originally installed in ISA board).
EPSON Color Copy Station 8200 Revision A 4. Turn the Color Copy Station 8200 on. The LED indicators show the update status; refer to the table below for details. Master Board Table 4-4. Control Panel indicators Update Process Error (red) Ready (green) Power (green) Contents Power ON l l m Deleting Target Data l m m Reading from MASTER m m m Writing to TARGET l ¥ m Update Successful ¥ l m Update Failure â 4.
EPSON Color Copy Station 8200 Revision A 4.4.3 BIOS Re-Setting Table 4-5. SP97 Mother Board BIOS Setting Value Setting Item Setting Value 1. Remove the mother board. (Remove SCSI, ISA and PCI boards and connect the power supply unit) Primary Master Auto 2. Install the video card (EGA/VGA) to the open slot. Primary Slave Auto àNone Secondary Master Auto àNone Secondary Slave Auto àNone 4. Connect the keyboard to the keyboard connector on the mother board.
EPSON Color Copy Station 8200 Revision A Table 4-5. SP97 Mother Board BIOS Setting Value Setting Item Table 4-5.
EPSON Color Copy Station 8200 Revision A Table 4-5. SP97 Mother Board BIOS Setting Value Setting Item CPU Fan Speed Table 4-5. SP97 Mother Board BIOS Setting Value Setting Value Setting Item Setting Value xxxx RPM IRQ 15 Used By ISA No / ICU xxC / xxxF IRQ 1 Used by ISA No / ICU IRQ 3 Used By ISA No / ICU IRQ 5 Used By ISA No / ICU ISA MEM Block BASE Auto SYMBIOS SCSI BIOS Auto ** Thermal Monitor ** CPU Temperature ** Voltage Monitor ** VCORE Voltage 2.2V + 3.3V Voltage 3.
EPSON Color Copy Station 8200 Revision A 4.4.4 Mother Board Jumper Setting Setting of the jumper switch (KB_UP, DIP1, DIP2) on the mother board is as follows. (See “Mother Board Removal” on page 48) Table 4-6. Jumper Switch Setting Jumper Switch No.
CHAPTER 5 ADJUSTMENT
EPSON Color Copy Station 8200 Revision A 5.1 Adjustment VARIOUS HARDWARE CHECK This chapter explains the following adjustments which are required to do for maintenance. o LCD panel check o ISA board check o Color Calibration Function o ECP board check o Mechanical Precision Adjustment o Flash ROM check sum confirmation o Hardware Check o H/W all check print o size collection 5.1.1 Hardware Check This function is used to check the hardware of the copy server.
EPSON Color Copy Station 8200 Revision A This function makes all the elements on the LCD show black. Due to this, you can check dots missing on the LCD. Press the “STOP” button and go back to the panel unit check main menu. If you press twelve ten key and three special key, the pressed indicator will disappear. When all the key pressed, the screen goes back to the panel unit check main menu. o GRAY SHADE Check The LCD is divided into four screens and indicates four graduations.
EPSON Color Copy Station 8200 Revision A o TOUCH KEY Check If you start this check, the LCD indicates as shown below. If you touch the black TOUCH KEY, the black color at the touched position will become the back ground color. If you clear all the black panel, the screen goes back to the panel unit check main menu. o All Check This function checks all from ALL BACK Check to TOUCH KEY Check. Go to check by “START” button.
EPSON Color Copy Station 8200 Revision A 5.1.1.2 ISA Board Check 5.1.1.3 ECP Board Check This hardware check function connects and assures the performance of SRAM for ISA board indicator and EEPROM. If you press “2” of ten key, the following panel unit check main menu appears. If you select this mode, OK / NG is indicated with the following display. This hard ware check function conceits and assures performance of various parts of PCI board.
EPSON Color Copy Station 8200 Revision A n RGB DATA PASS n MEMORY Check On the RGB CONTROL menu, press “3” of ten key, this function performs DMA transfer through ECP board in the following order: ASIC PCI à TET à MOIRE à SHARP à CMN à DMA, and checks BUS. On the RGB CONTROL menu, press “1” of ten key, and this function checks TET, MOIRE, SHARP, CMM, SRAM on the ECP board as shown below. Based on its check result, the display indicates "OK" if it performs right and indicates ’NG’ if it does not. 1.
EPSON Color Copy Station 8200 Revision A o B UNIT Check This function checks interruption from bill recognition unit (BILL) and memory and RGB input. Based on the test result, the display indicates "OK" if it performs right and indicates ’NG’ if it does not. [3.2] B UNIT a. ROM b. RAM c. INTERRUPT d. RGB1 e. RGB2 5.1.1.5 H/W All Check Printing On the maintenance mood main view, press “5” of ten key. After the hardware all check done inside, the check result will be printed out.
EPSON Color Copy Station 8200 Revision A 5.1.2 Size Collection (Adjusting the Precision) This function adjusts the mechanical precision (the individual differences) between the scanner and the printer, and minimizes the measurement gap between the original and the copy result.
EPSON Color Copy Station 8200 4. Revision A Set the printed mechanical precision adjustment pattern on the scanner and push down the “START” button. The scanner scans the data. [6] SIZE_CORRECT Size Correct in progress Please wait EXIT: STOP BUTTON NOTE: If an error occurs while scanning, re-try function works. 5. The adjusting measure is automatically calculated, and when the process finishes, the display goes back to the maintenance mood main view.
CHAPTER 6 MAINTENANCE
EPSON Color Copy Station 8200 Revision A 6.1 Maintenance For outer cases, wipe stain off with a clean and dry soft cloth. To remove sever stain, use neutral detergent. For inner parts, use the vacuum cleaner to remove dust or foreign objects. C A U T IO N Do not use chemical solvents, such as thinner and benzine for cleaning. These chemicals may damage the plastic and rubber parts.
CHAPTER 7 APPENDIX
EPSON Color Copy Station 8200 Revision A 7.1 Unit Connection CCS-8200 unit connection is as follows. CCS-8200 Mother Board P5S-B PCI Slot ECP Board C85010*IF-B ISA Slot SCSI Board AVA-2904BE ISA Slot ISA Board C85010*IF ISA Slot 100 Base TX Interface DE-500BA (DEC) Printer LP-8200C SCANNER ES-6000 Control Panel Switching Hub Power Supply Unit TSS-1500NS Figure 7-1.
EPSON Color Copy Station 8200 Revision A 7.2 Component Layout Figure 7-2. C85010 I/F (ISA Board) Component Layout (1) Appendix Figure 7-3.
EPSON Color Copy Station 8200 Revision A Figure 7-4.
EPSON Color Copy Station 8200 Revision A 7.3 Exploded Diagram 112 100 450 113 114 111 104 101 104 102 112 240 200 104 103 113 104 104 104 104 107 110 104 104 230 111 104 400 220 100 A 104 300 250 108 104 402 INTERFACE CABLE (Printer Cable) 109 106 104 260 include 100 410 (2 pcs CS-6000N) 331 105 LABEL CAUTION (Stick on S canner) 210 104 104 CS-6000N Rev.01 1942 Figure 7-5.
EPSON Color Copy Station 8200 Revision A 7.4 Electric Circuit Diagrams Refer to the corresponding pages for the Electric Circuit Diagrams listed below.