Start Here Card

ManualsBrandsEpson ManualsPrintersCX6400

1 Insert the paper support into the slots behind the printer, as shown.

2 Lower the feeder guard into the slots behind the scanner lid.

(Insert the hinges on the feeder guard into the corresponding

slots on the printer.)

EPSON Stylus

CX6400

Start Here

1 Wait until you see “Initial Charge” displayed on the control panel.

2 Lift up the scanner section.

3 Shake the package of ink cartridges four or five times.

Then remove the cartridges from the package.

Caution: You must install all cartridges and leave them installed

for all types of printing. To avoid damaging the Stylus CX, never

move the print head by hand.

4 Open the cartridge cover.

5 Place each cartridge in its holder.

6 Press down on each cartridge until it clicks into place.

Install Ink Cartridges

1 Extend the output tray.

2 Slide the edge guide to the left.

3 Place a stack of paper against the right side of the feeder,

but don’t push it in. Slide the edge guide against the paper.

7 Close the ink cartridge cover, then close the scanner section.

The Stylus CX begins charging the ink delivery system.

Charging takes about 2 minutes. The green light flashes and the

Stylus CX makes various sounds. Don’t turn it off while the green

light is flashing or you’ll waste ink.

1 Make sure you have all the parts shown here. If any parts are missing,

contact EPSON

as described on the back of this sheet.

2 Remove all blue packing tape from the printer.

3 Lift up the scanner section. If it doesn’t open, make sure you have

removed all the tape.

4 Peel off the tape from the ink cartridge holder.

5 Close the scanner section.

Unpack

Turn over

Load Paper

Attach the Parts

1 Plug the Stylus CX into a grounded electrical outlet.

Caution: Do not connect the USB cable until instructed.

2 Press and hold the On button until the green lights come on.

Plug In and Turn On

Paper support

Software

CD-ROM

Quick Reference

EPSON Stylus CX6400

Ink cartridges Feeder guard

Don’t touch the green part

CPD-16930R1 4049040-00 XXX

On button

continue

Summary of content (8 pages)

PAGE 1
Start Here EPSON Stylus CX6400 4 Install Ink Cartridges ® 1 Unpack CPD-16930R1 4049040-00 XXX 1 2 Attach the Parts 1 1 Wait until you see “Initial Charge” displayed on the control panel. 2 Lift up the scanner section. 7 Close the ink cartridge cover, then close the scanner section. Insert the paper support into the slots behind the printer, as shown. Make sure you have all the parts shown here. If any parts are missing, contact EPSON® as described on the back of this sheet.
PAGE 2
Start Here EPSON Stylus CX6400 4 Install Ink Cartridges ® 1 Unpack CPD-16930R1 4049040-00 XXX 1 2 Attach the Parts 1 1 Wait until you see “Initial Charge” displayed on the control panel. 2 Lift up the scanner section. 7 Close the ink cartridge cover, then close the scanner section. Insert the paper support into the slots behind the printer, as shown. Make sure you have all the parts shown here. If any parts are missing, contact EPSON® as described on the back of this sheet.
PAGE 3
Start Here EPSON Stylus CX6400 4 Install Ink Cartridges ® 1 Unpack CPD-16930R1 4049040-00 XXX 1 2 Attach the Parts 1 1 Wait until you see “Initial Charge” displayed on the control panel. 2 Lift up the scanner section. 7 Close the ink cartridge cover, then close the scanner section. Insert the paper support into the slots behind the printer, as shown. Make sure you have all the parts shown here. If any parts are missing, contact EPSON® as described on the back of this sheet.
PAGE 4
Start Here EPSON Stylus CX6400 4 Install Ink Cartridges ® 1 Unpack CPD-16930R1 4049040-00 XXX 1 2 Attach the Parts 1 1 Wait until you see “Initial Charge” displayed on the control panel. 2 Lift up the scanner section. 7 Close the ink cartridge cover, then close the scanner section. Insert the paper support into the slots behind the printer, as shown. Make sure you have all the parts shown here. If any parts are missing, contact EPSON® as described on the back of this sheet.
PAGE 5
6 Install Software and Connect to Your Computer The software works with Windows® 98, Me, 2000, and XP, and Macintosh® OS 8.6 to 9.x and 10.2 to 10.3. Follow the steps below (for Windows), or the steps in the next column (for Macintosh). Macintosh Selecting the Stylus CX for Mac OS X Any Questions? 1 1 Here’s where to look for answers: 2 Note: There is a Security Lock program on your CD-ROM that lets you prevent unauthorized use of your CX6400.
PAGE 6
Install Software and Connect to Your Computer The software works with Windows® 98, Me, 2000, and XP, and Macintosh® OS 8.6 to 9.x and 10.2 to 10.3. Follow the steps below (for Windows), or the steps in the next column (for Macintosh). Macintosh Selecting the Stylus CX for Mac OS X Any Questions? 1 1 Here’s where to look for answers: 2 Note: There is a Security Lock program on your CD-ROM that lets you prevent unauthorized use of your CX6400.
PAGE 7
6 Install Software and Connect to Your Computer The software works with Windows® 98, Me, 2000, and XP, and Macintosh® OS 8.6 to 9.x and 10.2 to 10.3. Follow the steps below (for Windows), or the steps in the next column (for Macintosh). Macintosh Selecting the Stylus CX for Mac OS X Any Questions? 1 1 Here’s where to look for answers: 2 Note: There is a Security Lock program on your CD-ROM that lets you prevent unauthorized use of your CX6400.
PAGE 8
6 Install Software and Connect to Your Computer The software works with Windows® 98, Me, 2000, and XP, and Macintosh® OS 8.6 to 9.x and 10.2 to 10.3. Follow the steps below (for Windows), or the steps in the next column (for Macintosh). Macintosh Selecting the Stylus CX for Mac OS X Any Questions? 1 1 Here’s where to look for answers: 2 Note: There is a Security Lock program on your CD-ROM that lets you prevent unauthorized use of your CX6400.