User's Guide
Contents 2 Notations Used in This Guide 6 Introduction to Your Projector 7 Projector Features.............................................................................. 8 Quick and Easy Setup..................................................................................................................... 8 Easy Wireless Projection................................................................................................................ 8 Flexible Connectivity ...............................
Contents 3 Available Image Aspect Ratios ................................................................................................. 48 Projected Image Appearance with Each Aspect Mode .................................................. 49 Color Mode ....................................................................................... 50 Changing the Color Mode ......................................................................................................... 50 Available Color Modes........
Contents 4 Setting Up Monitoring Using SNMP............................................... 97 Maintaining the Projector Adjusting the Menu Settings Cleaning the Lens........................................................................... 125 98 Using the Projector's Menus ........................................................... 99 Using the On-screen Keyboard..................................................... 100 124 Cleaning the Projector Case...............................................
Contents 5 Solving Projector or Remote Control Operation Problems ....... 146 Solutions to Projector Power or Shut-Off Problems...................................................... 146 Solutions to Problems with the Remote Control............................................................ 146 Solutions to Password Problems........................................................................................... 147 Solving Network Problems ...........................................................
Notations Used in This Guide Safety Symbols The projector and its manuals use graphical symbols and labels to indicate content that tells you how to use the projector safely. Read and carefully follow the instructions that are marked with these symbols and labels to avoid injury to persons or damage to property. Warning Caution This symbol indicates information that, if ignored, could possibly result in personal injury or even death.
Introduction to Your Projector Refer to these sections to learn more about your projector's features and part names. g Related Links • "Projector Features" p.8 • "Projector Parts and Functions" p.
Projector Features This projector comes with this special features. Refer to these sections for more details. g Related Links • "Quick and Easy Setup" p.8 • "Easy Wireless Projection" p.8 • "Flexible Connectivity" p.9 8 Easy Wireless Projection • Screen Mirroring to connect your projector and mobile device wirelessly using Miracast technology (EB‑U42). Quick and Easy Setup • Direct Power On feature to turn on the projector as soon as you plug it in.
Projector Features a • When projecting images using a wireless LAN, you must install the Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection (EB‑W41/EB‑X41/EB‑S41/EB‑U05/EB‑W05/EB‑X05/EB‑S05/EB‑U1 40/EB‑W140/EB‑X140/EB‑S140/EB‑X450/EB‑X400/EB‑S400). Depending on your projector model, you may need to purchase the optional wireless LAN module. See the Quick Start Guide for a list of items supplied with your projector.
Projector Parts and Functions The following sections explain the projector parts and their functions. 10 Name All of the features in this guide are explained using illustrations of EB‑W05 unless otherwise mentioned. Function Warning g Related Links • "Projector Parts - Front" p.10 • "Projector Parts - Rear" p.11 • "Projector Parts - Base" p.12 • "Projector Parts - Control Panel" p.13 • "Projector Parts - Remote Control" p.14 Do not look into the vents.
Projector Parts and Functions Name Function 11 EB‑W42/EB‑W41/EB‑X41/EB‑S41/EB‑W05/EB‑X05/EB‑S05/EB‑W140/EB‑X1 40/EB‑S140/EB‑X450/EB‑X400/EB‑S400 K Security slot The security slot is compatible with the Microsaver Security System manufactured by Kensington. L Control panel Operates the projector. M Zoom ring Adjusts the image size. (EB‑U42/EB‑W42/EB‑ W41/EB‑X41/EB‑U05 /EB‑W05/EB‑X05/EB‑ U140/EB‑W140/EB‑X 140/EB‑X450/EB‑X40 0) N Focus ring Adjusts the image focus.
Projector Parts and Functions Name Function G HDMI1, HDMI2/MHL ports (EB‑U42/EB‑U05/EB‑ U140) HDMI/MHL port (EB‑W42/EB‑W41) HDMI port (EB‑X41/EB‑S41/EB‑ W05/EB‑X05/EB‑S05/ EB‑W140/EB‑X140/E B‑S140/EB‑X450/EB‑ X400/EB‑S400) Inputs video signals from HDMI compatible video equipment and computers. The HDMI/MHL port can also input video signals from MHL (Mobile High-Definition) compatible mobile devices. This projector is compatible with HDCP.
Projector Parts and Functions Name D Front adjustable foot 13 Function Name When the projector is set up on a surface such as a desk, extend the foot to adjust the position of the image. C Keystone adjustment buttons and arrow buttons Displays the Keystone screen allowing you to correct keystone distortion. Selects menu items while displaying the projector's menu or help. D [Esc] button Stops the current function. Moves back to the previous menu level while displaying the projector's menu.
Projector Parts and Functions Projector Parts - Remote Control 14 Name Function A Power button [ ] Turns the projector on or off. B [Computer] button Selects the Computer port as the image source. C [HDMI/Video] button Switches the image source between the HDMI and Video ports. D Numeric buttons Enters numbers in the projector's menu while holding down the [Num] button. E [Auto] button Optimizes Tracking, Sync.
Projector Parts and Functions Name Function Projects two images from different image sources O [Split] button (EB‑U42/EB‑W42/ simultaneously by splitting the projected screen. EB‑W41/EB‑U05/E B‑W05/EB‑U140/E B‑W140) P [Home] button Displays and closes the Home screen. Q [Freeze] button Pauses or resumes images. R [Volume] up/down buttons Adjusts the speaker volume. S [Pointer] button Displays the on-screen pointer. T [Esc] button Stops the current function.
Setting Up the Projector Follow the instructions in these sections to set up your projector. g Related Links • "Projector Placement" p.17 • "Projector Connections" p.19 • "Installing Batteries in the Remote Control" p.26 • "Remote Control Operation" p.27 • "Opening the Lens Cover" p.
Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location. An optional ceiling mount is required when suspending the projector from a ceiling. Note the following points when selecting a projector location: • Place the projector on a sturdy, level surface or install it using a compatible mount.
Projector Placement Projector Setup and Installation Options You can set up or install your projector in the following ways: Front/Rear 18 projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings. See the Appendix for details about how far to place the projector from the screen based on the size of the projected image. a When correcting keystone distortion, your image is slightly smaller.
Projector Connections You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images, with or without sound. 19 g Related Links • "Connecting to a Computer for VGA Video and Audio" p.19 • "Connecting to a Computer for USB Video and Audio" p.20 • "Connecting to a Computer for HDMI Video and Audio" p.21 Attention Check the shape and orientation of the connectors on any cable you plan to connect.
Projector Connections e Connect the other end to the projector's Audio ports. 20 c Turn on the projector and your computer. d Do one of the following to install the Epson USB Display software: a You only need to install this software the first time you connect the projector to the computer. • Windows: Select Run EMP_UDSE.EXE in the dialog box that is displayed to install the Epson USB Display software.
Projector Connections Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an HDMI cable and send the computer's audio with the projected image. a 21 a Connect the MHL cable to your device's Micro-USB port. the other end to the projector's HDMI/MHL port. b Connect EB‑U42/EB‑U05/EB‑U140 To connect a Mac that does not have an HDMI port, you need an adapter that allows you to connect to the projector's HDMI port.
Projector Connections work or you may not be able to perform operations using the projector's remote control. a • Charging may not work when using a lot of power, such as when playing a movie. • Charging does not work when the projector is in standby mode or the battery in a smartphone or tablet is depleted. 22 Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an HDMI cable and send the image source's audio with the projected image.
Projector Connections the component connectors to your video source's color-coded a Connect component video output ports. a The ports usually labeled Y, Pb, Pr or Y, Cb, Cr. If you are using an adapter, connect these connectors to your component video cable. b Connect the VGA connector to a Computer port on the projector. 23 If your image colors appear incorrectly, you may need to change the Input Signal setting in the projector's Signal menu.
Projector Connections d Connect the other end to the projector's Audio ports. 24 a • Digital cameras or smartphones must be USB-mounted devices, not TWAIN-compliant devices, and must be USB Mass Storage Classcompliant.
Projector Connections Attention • Use the USB cable supplied with or specified for use with the device. • Do not connect a USB hub or a USB cable longer than 3 meters, or the device may not operate correctly. c Connect the other end to your device, if necessary. Disconnecting a USB Device When you have finished presenting with a connected USB device, disconnect the device from the projector. a Turn off and unplug the device, if necessary. b Disconnect the USB device from the projector.
Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Attention Make sure you read the Safety Instructions before handling the batteries. a Remove the battery cover as shown. b Insert the batteries with the + and – ends facing as shown. 26 Warning Check the positions of the (+) and (–) marks inside the battery holder to ensure the batteries are inserted the correct way.
Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here. a Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you are not going to use the remote control for a long time, remove the batteries.
Opening the Lens Cover open the projector's lens cover, slide the A/V Mute slide lever until a Toit clicks. cover the lens or temporarily turn off the projected image and b Tosound, close the lens cover.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features. g Related Links • "Turning On the Projector" p.30 • "Turning Off the Projector" p.33 • "Selecting the Language for the Projector Menus" p.34 • "Projection Modes" p.35 • "Adjusting the Image Height" p.37 • "Image Shape" p.38 • "Resizing the Image with the Zoom Ring" p.43 • "Resizing the Image with the Buttons" p.44 • "Focusing the Image Using the Focus Ring" p.45 • "Selecting an Image Source" p.
Turning On the Projector Turn on the computer or video equipment you want to use after you turn on the projector. 30 c Open the projector's lens cover. the power cord to the projector's power inlet and plug it into a Connect an electrical outlet. Try the following if you do not see a projected image. The projector's power indicator turns blue. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode).
Turning On the Projector Warning • Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children. • When turning on the projector at a distance using the remote control, make sure there is no one looking into the lens. • During projection, do not block the light from the projector with a book or other objects.
Turning On the Projector F Projects two images from different image sources simultaneously by splitting the projected screen (EB‑U42/EB‑W42/EB‑W41/EB‑U05/EB‑W05/EB‑U140/EB‑W140). Selects the brightness mode of the projector lamp (EB‑X41/EB‑S41/EB‑X05/EB‑S05/EB‑X140/EB‑S140/EB‑X450/EB‑X400/EB‑S400 ). G Corrects the shape of an image that is an uneven rectangle. a The Home screen disappears after 10 minutes of inactivity. g Related Links • "Image Shape" p.38 • "Projector Setup Settings - Extended Menu" p.
Turning Off the Projector Turn off the projector after use. a • Turn off this product when it is not in use to prolong the life of the projector. Lamp life varies depending on the mode selected, environmental conditions, and usage. Brightness decreases over time. • Since the projector supports the direct shutdown feature, it can be turned off directly using the breaker.
Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. a Turn on the projector. b Press the [Menu] button on the control panel or remote control. c Select the Extended menu and press [Enter]. d Select the Language setting and press [Enter]. e Select the language you want to use and press [Enter]. 34 f Press [Menu] or [Esc] to exit the menus.
Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen.
Projection Modes d Select Projection and press [Enter]. e Select a projection mode and press [Enter]. f Press [Menu] or [Esc] to exit the menus.
Adjusting the Image Height If you are projecting from a table or other flat surface and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 37 d If the image is tilted, rotate the rear feet to adjust their height. The larger the angle of tilt, the harder it becomes to focus. Locate the projector so that it only needs to be tilted at a small angle. a Turn on the projector and display an image.
Image Shape You can project an even, rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilt it up or down, or off to the side, you may need to correct the image shape. g Related Links • "Auto V-Keystone" p.38 • "Correcting the Image Shape with the Horizontal Keystone Slider" p.38 • "Correcting the Image Shape with the Keystone Buttons" p.39 • "Correcting the Image Shape with Quick Corner" p.
Image Shape Correcting the Image Shape with the Keystone Buttons 39 c Press a keystone button to adjust the image shape. You can use the projector's keystone correction buttons to correct the shape of an image that is unevenly rectangular. You can use keystone buttons to correct images up to 30º right, left, up, or down. a Turn on the projector and display an image. one of the keystone adjustment buttons on the control panel to b Press display the Keystone adjustment screen.
Image Shape g Related Links • "Projector Feature Settings - Settings Menu" p.104 40 c Select the Settings menu and press [Enter]. Correcting the Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular. d Select Keystone and press [Enter]. a Turn on the projector and display an image. b Press the [Menu] button on the control panel or remote control.
Image Shape e Select Quick Corner and press [Enter]. Press [Enter] again if necessary. 41 a • If you see this screen, you cannot adjust the shape any further in the direction indicated by the gray triangle. You see the area selection screen. the arrow buttons to select the corner of the image you want to f Use adjust. Then press [Enter]. • To reset the Quick Corner corrections, hold down [Esc] for about 2 seconds while the Quick Corner adjustment screen is displayed, and select Reset Quick Corner.
Image Shape g Related Links • "Projector Feature Settings - Settings Menu" p.
Resizing the Image with the Zoom Ring You can resize the image using the projector's zoom ring (EB‑U42/EB‑W42/EB‑W41/EB‑X41/EB‑U05/EB‑W05/EB‑X05/EB‑U140/EB‑W 140/EB‑X140/EB‑X450/EB‑X400). a Turn on the projector and display an image. b Rotate the zoom ring to enlarge or reduce the image.
Resizing the Image with the Buttons You can resize the image using the Wide and Tele buttons (EB‑S41/EB‑S05/EB‑S140/EB‑S400). a Turn on the projector and display an image. the Wide button on the projector's control panel to enlarge the b Press image size. Press the Tele button to reduce the image size.
Focusing the Image Using the Focus Ring You can correct the focus using the focus ring.
Selecting an Image Source When multiple image sources are connected to the projector, such as a computer and DVD player, you can switch from one image source to the other. 46 a This screen is displayed when no image signal is detected. Check the cable connections between the projector and image source. a Make sure the connected image source you want to use is turned on. video image sources, insert a DVD or other video media and press b For play.
Selecting an Image Source • Press the [Home] button on the control panel or remote control. Then select the source you want to use from the screen displayed. a • Screen Mirroring is available only with the EB‑U42. • HDMI2 is available only with the EB‑U42/EB‑05.
Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally, the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen. If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's Signal menu. g Related Links • "Changing the Image Aspect Ratio" p.48 • "Available Image Aspect Ratios" p.
Image Aspect Ratio 49 Aspect mode Description Aspect mode Native Displays images as is (aspect ratio and resolution are maintained). Aspect ratio for input signals 16:10 16:9 4:3 16:9 For projectors with a resolution of XGA (1024 × 768) or SVGA (800 × 600) Full Aspect mode Description Auto Automatically sets the aspect ratio according to the input signal and the Resolution setting. Normal Displays images using the full projection area and maintains the aspect ratio of the image.
Color Mode The projector offers different color modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types. You can select the mode designed to match your image and environment, or experiment with the available modes. g Related Links • "Changing the Color Mode" p.50 • "Available Color Modes" p.50 • "Setting Auto Iris" p.50 Changing the Color Mode 50 a You can also set the Color Mode setting in the projector's Image menu.
Color Mode b Press the [Menu] button on the control panel or remote control. 51 d Select Auto Iris and press [Enter]. c Select the Image menu and press [Enter]. one of the following options and press [Enter]: e Choose • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment. f Press [Menu] or [Esc] to exit the menus.
Controlling the Volume with the Volume Buttons The volume buttons control the projector's internal speaker system. You must adjust the volume separately for each connected input source. a Turn on the projector and start a presentation. lower or raise the volume, press the [Volume] buttons on the b Tocontrol panel or remote control as shown. a The [Volume] buttons on the control panel are available only with EB‑U42/EB‑W42/EB‑W41/EB‑X41/EB‑U05/EB‑W05/EB‑X05/EB‑ U140/EB‑W140/EB‑X140/EB‑X450/EB‑X400.
Adjusting Projector Features Follow the instructions in these sections to use your projector's adjustment features. g Related Links • "Projecting Two Images Simultaneously" p.54 • "Projecting a PC Free Presentation" p.57 • "Shutting Off the Image and Sound Temporarily" p.62 • "Stopping Video Action Temporarily" p.63 • "Zooming Images" p.64 • "Using the Remote Control as a Wireless Mouse" p.65 • "Using the Remote Control as a Pointer" p.67 • "Saving a User's Logo Image" p.
Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources (EB‑U42/EB‑W42/EB‑W41/EB‑U05/EB‑W05/EB‑U140/EB‑W140). You can control the split screen feature using the remote control or the projector menus. 54 a Press the [Split] button on the remote control. The currently selected input source moves to the left of the screen. a You can perform the same operations from Split Screen in the projector's Settings menu.
Projecting Two Images Simultaneously an input source for the other image, select the Source setting, c Topressselect [Enter], select the input source, select Execute, and press [Enter]. 55 one image while reducing the other image, select Screen e ToSize,enlarge press [Enter], select a size, and press [Enter]. To exit the menu, press [Menu]. a Depending on the video input signals, the images may not appear at the same size even if you select Equal.
Projecting Two Images Simultaneously • • • • • Computer and Video HDMI1 and Screen Mirroring (EB‑U42) USB Display and USB/LAN USB and LAN LAN and Screen Mirroring (EB‑U42) Split Screen Projection Restrictions Operating restrictions The following operations cannot be performed during split screen projection.
Projecting a PC Free Presentation You can use your projector's PC Free feature whenever you connect a USB device that contains compatible presentation files. This lets you quickly and easily display a presentation and control it using the projector's remote control. g Related Links • "Supported PC Free File Types" p.57 • "Precautions on PC Free Projection" p.57 • "Starting a PC Free Slide Show" p.58 • "Starting a PC Free Movie Presentation" p.59 • "PC Free Display Options" p.
Projecting a PC Free Presentation • You may not be able to use the security features on certain USB storage devices with PC Free features. • When connecting a USB device that includes an AC adapter, connect the AC adapter to an electrical outlet when you use the device with your projector. • Some commercially available USB card readers may not be compatible with the projector. • The projector can recognize up to 5 cards inserted into the connected card reader at one time.
Projecting a PC Free Presentation • To display a slide show of all the images in a folder, press the arrow buttons to highlight the Slideshow option at the bottom of the screen and press [Enter]. a • You can change the image switching time by highlighting Option at the bottom of the screen and pressing [Enter]. • If any file names are longer than the display area or include unsupported symbols, the file names may be shortened or changed only on the screen display.
Projecting a PC Free Presentation a • If the Select Drive screen is displayed, press the arrow buttons to select the drive and press [Enter]. • To display the Select Drive screen, highlight Select Drive at the top of the file list screen and press [Enter]. 60 PC Free Display Options You can select these display options when using PC Free. To access this screen, highlight Option at the bottom of the PC Free file list screen and press [Enter].
Projecting a PC Free Presentation Setting Options Description Effect No No effect Wipe Transitions between images using a wipe effect Dissolve Transitions between images using a dissolve effect Random Transitions between images using a random variety of effects 61
Shutting Off the Image and Sound Temporarily You can temporarily turn off the projected image and sound if you want to redirect your audience's attention during a presentation. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. a If you want to display an image such as a company logo or picture when the [A/V Mute] button is pressed, you can select the screen displayed in the A/V Mute setting in the projector's Extended menu.
Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. the [Freeze] button on the remote control to stop the video a Press action. b To restart the video action in progress, press [Freeze] again.
Zooming Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen. 64 The enlarged image is projected and the enlargement ratio is displayed on the screen. You can enlarge the selected area to between one to four times in 25 incremental steps. When projecting images from an Epson document camera using a USB connection, you can enlarge the selected area from one to eight times its size in 57 incremental steps.
Using the Remote Control as a Wireless Mouse You can use the projector's remote control as a wireless mouse so you can control projection at a distance from the computer. a 65 the following buttons on the remote control to control your d Use presentation: You can use the wireless mouse features with Windows Vista and later, or OS X 10.7.x and later. the projector to a computer using the projector's USB-B, a Connect Computer, or HDMI port.
Using the Remote Control as a Wireless Mouse g Related Links • "Zooming Images" p.64 • "Using the Remote Control as a Pointer" p.
Using the Remote Control as a Pointer You can use the projector's remote control as a pointer to help you focus your audience on important information on the screen. The default pointer shape is an arrow. You can change the shape in the Pointer Shape setting in the projector's Settings menu. a Press the [Pointer] button on the remote control. the arrow buttons to move the pointer on the screen. To move the b Use pointer diagonally, press any pair of adjacent arrow buttons at the same time.
Saving a User's Logo Image You can save an image on the projector and display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using A/V Mute). This image is called the user's logo screen. 68 d Select User's Logo and press [Enter]. You can select a photo, graphic, or company logo as the user's logo, which is useful in identifying the projector's owner to help deter theft.
Saving a User's Logo Image the arrow buttons to surround the image area you want to use as f Use the user's logo and press [Enter]. You see a prompt asking if you want to select this image area. a You cannot change the image area size (400 × 300 pixels). Yes and press [Enter]. (If you want to change the selected area, g Select select No, press [Enter], and repeat the last step.) You see the User's Logo zoom factor menu. h Select a zoom percentage and press [Enter].
Color Difference Correction when Projecting from Multiple Projectors When lining up multiple projectors to project images, you can correct the brightness and color tone of each projector's image so that the images match closely. 70 the arrow buttons to select the identification number you want to d Use use for the projector. Then press [Enter].
Color Difference Correction when Projecting from Multiple Projectors the remote control at the target projector and press the [ID] a Aim button. 71 holding the [ID] button, press the number button that matches b While the ID of the projector you want to operate. The current Projector ID is displayed on the projected screen. It disappears after about 3 seconds. The projector you want to operate is selected. the [ID] button to check if the ID-setting process worked.
Color Difference Correction when Projecting from Multiple Projectors Matching Multiple-Projector Display Quality You can match the display quality of multiple projectors that will project next to each other. on all the projectors on which you want to match the display a Turn quality. b Set ID numbers on each projector. c Make sure all the projectors are using the same Color Mode setting. d Select the remote control ID to match the first projector.
Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent people who do not know the password from using the projector, and prevent changes to the startup screen and other settings. This acts as an anti-theft function as the projector cannot be used even if it is stolen, and you can limit who can use the projector.
Projector Security Features b Select Password and press [Enter]. 74 The password displays as **** as it is entered. A confirmation prompt is displayed when you enter the fourth digit. the password again. e Enter You see the message "Password accepted". If you enter the password incorrectly, a message is displayed prompting you to re-enter the password. f Press [Esc] to return to the menu. g Make a note of the password and keep it in a safe place. You see the prompt "Change the password?".
Projector Security Features • To prevent changes to the projector's Screen Mirroring settings, select On as the Screen Mirroring Protec. setting (EB‑U42). You can attach the password protect sticker to the projector as an additional theft deterrent. a Be sure to keep the remote control in a safe place; if you lose it, you will not be able to enter the password. Entering a Password to Use the Projector When the password screen is displayed, enter the correct password. 75 The password screen closes.
Projector Security Features 76 b Select the Settings menu and press [Enter]. d Select Control Panel Lock and press [Enter]. c Select Lock Setting and press [Enter]. one of these lock types and press [Enter]: e Select • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. Yes and press [Enter]. f Select The Control Panel Lock setting takes effect.
Projector Security Features s Settings > Lock Setting > Control Panel Lock g Related Links • "Projector Feature Settings - Settings Menu" p.104 Installing a Security Cable You can install the security cable on the projector to deter theft. • Use the security slot on the projector to attach a Kensington Microsaver Security system. a For more details on the Microsaver Security System, see http://www.kensington.com/.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. g Related Links • "Wireless Network Projection" p.79 • "Wireless Network Projection from a Mobile Device (Screen Mirroring)" p.
Wireless Network Projection You can send images to your projector through a wireless network. • To do this, you must install the Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection (EB‑W41/EB‑X41/EB‑S41/EB‑U05/EB‑W05/EB‑X05/EB‑S05/EB‑U140/EB‑ W140/EB‑X140/EB‑S140/EB‑X450/EB‑X400/EB‑S400). • Some models have built-in wireless LAN modules (EB‑U42/EB‑W42). You don't need to install the Epson 802.11b/g/n wireless LAN module.
Wireless Network Projection b Connect the wireless LAN module to the USB-A port. 80 Selecting Wireless Network Settings Manually Before you can project from your wireless network, you need to select network settings for the projector. a Press the [Menu] button on the control panel or remote control. b Select the Network menu and press [Enter]. the wireless LAN module cover, and secure it in place with the c Attach screw.
Wireless Network Projection c Select Wireless LAN On as the Wireless Mode setting. 81 the basic options as necessary. f Select • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector using the Basic Control. (User name is EPSONREMOTE; default password is guest.
Wireless Network Projection g Select the Wireless LAN menu and press [Enter]. 82 • If you want to connect the projector to the network using IPv6, select IPv6 Settings to set the IPv6 setting to On, and then set the Auto Configuration and Use Temporary Address settings as necessary. prevent the SSID or IP address from being displayed on the LAN k Tostandby screen and Home screen, set the SSID Display setting or the IP Address Display setting to Off.
Wireless Network Projection Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. access your wireless utility software, double-click the network icon a Toon the Windows taskbar. connecting in Advanced connection mode, select the network b When name (SSID) of the network the projector is connecting to. c Click Connect.
Wireless Network Projection e Select the Security setting and press [Enter]. 84 the [LAN] button on the remote control. a Press The QR code is displayed on the projected surface. a • If you do not see the QR code, set the Display LAN Info. setting to Text & QR Code in the projector's Network menu. s Network > Network Configuration > Basic > Display LAN Info. • To hide the QR code, press the [Esc] button. • When the QR code is hidden, press the [Enter] button to display the code.
Wireless Network Projection sure the wireless LAN module is installed or built into your b Make projector. c Turn on the projector. the [LAN] button on the remote control. d Press The LAN standby screen is displayed. Verify that an SSID and IP address are displayed. one of the following to connect the USB key. e Do • Connect the USB key to the projector's USB-A port (EB‑U42/EB‑W42).
Wireless Network Projection from a Mobile Device (Screen Mirroring) You can send image to your projector from mobile devices such as laptops, smartphones, and tablets using Miracast technology (EB‑U42). If your device supports Miracast, you do not need to install any additional software. When using a Windows computer, make sure the necessary adapter for the Miracast connection is available. Note the following limitations when using Screen Mirroring features. • You cannot play an interlaced image.
Wireless Network Projection from a Mobile Device (Screen Mirroring) c Select Screen Mirroring On as the Wireless Mode setting. 87 e Set the Display Name setting as necessary. the Operation Mode setting. f Select • Basic lets you connect with basic options. d Select Screen Mirroring Settings and press [Enter]. • Extended lets you connect with advanced options. the Basic setting as necessary. g Select • Wireless LAN Sys. lets you select the type of wireless LAN system the projector is connecting to.
Wireless Network Projection from a Mobile Device (Screen Mirroring) the Display setting as necessary. i Select • Display PIN Code lets you display the PIN code on the projected 88 c Display Action Center, and then select Connect. image while projecting input sources other than Screen Mirroring. • Display Device Name lets you display the newly connected device name on the projected image while projecting input sources other than Screen Mirroring.
Wireless Network Projection from a Mobile Device (Screen Mirroring) a It may take some time until the connection is established. While connecting, do not disconnect the projector's power cord. Doing so may cause your device to freeze or malfunction. 89 d Select Add a wireless display. Connecting Using Screen Mirroring in Windows 8.1 You can set up your computer for wireless projection from Charms in Windows 8.1.
Wireless Network Projection from a Mobile Device (Screen Mirroring) a It may take some time until the connection is established. While connecting, do not disconnect the projector's power cord. Doing so may cause your device to freeze or malfunction. Connecting Using Screen Mirroring with the Miracast Function If your mobile device such as a smartphone supports Miracast, you can connect it to the projector wirelessly and project images.
Monitoring and Controlling the Projector Follow the instructions in these sections to monitor and control the projector over a network. g Related Links • "Epson Projector Management" p.92 • "Controlling a Networked Projector Using a Web Browser" p.93 • "Setting Up Projector Network E-Mail Alerts" p.96 • "Setting Up Monitoring Using SNMP" p.
Epson Projector Management Epson Projector Management software (Windows only) lets you monitor and control your projector through the network. See the Epson Projector Management Operation Guide for instructions. You can download Epson Projector Management from the following Web site. http://www.epson.
Controlling a Networked Projector Using a Web Browser Once you have connected your projector to your network, you can select projector settings and control projection using a compatible Web browser. This lets you access the projector remotely. a 93 You see the Epson Web Control screen. • Make sure the computer and projector are connected to the network. When projecting images using a wireless LAN, connect in Advanced connection mode. • You can use the following Web browsers. • Internet Explorer 9.
Controlling a Networked Projector Using a Web Browser the icon corresponding to the projector function you want to f Select control. 94 J Selects the network source K Selects the Screen Mirroring source (EB‑U42) L Selects Computer port source M Selects Video source N Searches for sources select projector menu settings, select Advanced on the Epson Web g ToControl screen. a • You can also change projector settings by accessing the projector menu system from OSD Control Pad.
Controlling a Networked Projector Using a Web Browser a • You cannot select the following settings using a Web browser. • Pointer Shape • User Button • User's Logo • Language • HDMI EQ Setting • Reset Lamp Hours • You can select the following settings only using a Web browser.
Setting Up Projector Network E-Mail Alerts You can set up the projector to send you an e-mail alert over the network if there is a problem with the projector. If you set the Standby Mode setting to Communication On in the projector's ECO menu, you can receive the e-mail alerts even if the projector is in standby mode (when the power is off). a Press the [Menu] button on the control panel or remote control. b Select the Network menu and press [Enter]. c Select Network Configuration and press [Enter].
Setting Up Monitoring Using SNMP Network administrators can install SNMP (Simple Network Management Protocol) software on network computers so they can monitor projectors. If your network uses this software, you can set up the projector for SNMP monitoring. a Press the [Menu] button on the control panel or remote control. b Select the Network menu and press [Enter]. c Select Network Configuration and press [Enter]. d Select the Notifications menu and press [Enter]. e Set the SNMP setting to On.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings. g Related Links • "Using the Projector's Menus" p.99 • "Using the On-screen Keyboard" p.100 • "Image Quality Settings - Image Menu" p.101 • "Input Signal Settings - Signal Menu" p.102 • "Projector Feature Settings - Settings Menu" p.104 • "Projector Setup Settings - Extended Menu" p.106 • "Projector Network Settings - Network Menu" p.
Using the Projector's Menus You can use the projector's menus to adjust the settings that control how your projector works. The projector displays the menus on the screen. a Press the [Menu] button on the control panel or remote control. You see the menu screen displaying the Image menu settings. the up or down arrow buttons to move through the menus listed b Press on the left. The settings for each menu are displayed on the right. a The available settings depend on the current input source.
Using the On-screen Keyboard 100 The on-screen keyboard is displayed when you need to enter numbers and characters. Text type Details Numbers 0123456789 the arrow buttons on the control panel or remote control to a Use highlight the number or character you want to enter and press the Alphabet ABCDEFGHIJKLMNOPQRSTUVWXY Z abcdefghijklmnopqrstuvwxyz Symbols !"#$%&'()*+,-./:;<=>?@[\] ^_`{|}~ [Enter] button.
Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source. 101 Setting Options Color Temp. Image Enhancement Sets the color tone based on color temperature. The image is tinted blue when a high value is selected and tinted red when a low value is selected. Color Temp. Color Temp.
Input Signal Settings - Signal Menu Normally the projector automatically detects and optimizes the input signal settings. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source. a a You cannot select settings on the Signal menu when the current input source is one of the following: • USB Display • USB • LAN • Screen Mirroring (EB‑U42) You can restore the default settings of the Tracking, Sync.
Input Signal Settings - Signal Menu Setting Reset Options Description Video Signal Video Signal: specifies the signal type from the input sources connected to the video ports. If interference appears or no image appears when set to Auto, select the appropriate signal according to the connected equipment. — Resets all adjustment values on the Signal menu to their default settings, except for the following: • Input Signal g Related Links • "Available Image Aspect Ratios" p.
Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features. 104 Setting Options Description Zoom ** Varying levels available Adjusts the size of the projected image. Volume Varying levels available Adjusts the volume of projector’s speaker system. Setting values are saved for each source. Lock Setting Control Panel Lock Controls projector button locking to secure the projector: Full Lock: locks all buttons.
Projector Feature Settings - Settings Menu Setting Options Description Test Pattern — Displays a test pattern to assist in focusing and zooming the image and correcting image shape (press the [Esc] button to cancel pattern display). Attention If a pattern is displayed for a long time, a residual image may be visible in projected images.
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features. 106 Setting Options Description Display Background Display Background: sets the screen color or logo to display when no signal is received. Startup Screen Startup Screen: set to On to display a logo when the projector starts up. A/V Mute A/V Mute: sets the screen color or logo to display when A/V Mute is turned on.
Projector Setup Settings - Extended Menu Setting Options Description HDMI EQ Setting Adjust the HDMI input signal level depending on the devices connected to the HDMI port. If there is a lot of interference in the image, or if a problem such as no image being projected occurs, change the setting. If no images are displayed using a thumb-sized media streaming device, select 1. Projector ID Off 1 through 9 Assigns an ID for the projector when you use multiple projectors.
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for controlling over a network. When you set Network Protection to On in the Password Protection screen, you cannot change the network settings. Set Network Protection to Off first. Setting Options Description Wireless Mode * Screen Mirroring On Wireless LAN On Both Settings Off Configures your wireless settings.
Projector Network Settings - Network Menu a Once you have connected your projector to your network, you can select projector settings and control projection using a compatible Web browser. This allows you to access the projector remotely. g Related Links • "Network Menu - Screen Mirroring Settings" p.109 • "Network Menu - Basic Menu" p.110 • "Network Menu - Wireless LAN Menu" p.111 • "Network Menu - Notifications Menu" p.112 • "Network Menu - Others Menu" p.113 • "Network Menu - Reset Menu" p.
Projector Network Settings - Network Menu 110 Setting Options Description Setting Options Description Display Display PIN Code Set to On to display the eight-digit PIN code on the projected image when projecting input sources other than Screen Mirroring. Projector Name Enter a name to identify the projector over the network. Display Device Name Set to On to display the newly connected device name on the projected image when projecting input sources other than Screen Mirroring.
Projector Network Settings - Network Menu Setting Options Description Display LAN Info. Text & QR Code Text Set the display format for the projector's network information. By simply reading the QR code with Epson iProjection, you can connect the mobile device to the projector through a network. The default value is Text & QR Code. 111 Setting Options Description Quick Quick: lets you connect to multiple smartphones, tablets, or computers directly using wireless communication.
Projector Network Settings - Network Menu Setting Options Description Passphrase Various passphrases from 8 to 32 characters (when entering from a Web browser: various passphrases from 8 to 63 characters) For WPA2-PSK and WPA/WPA2-PSK security, selects the pre-shared passphrase used on the network. When the passphrase is entered and the [Enter] button is pressed, the value is set and displayed as an asterisk (*). We recommend changing the passphrase periodically for security.
Projector Network Settings - Network Menu 113 Setting Options Description Setting Options Description Mail Notification On Off Set to On to send an email to the preset addresses when a problem or warning occurs with a projector. Community Name Set the SNMP community name. SMTP Server IP address Enter the IP address for the projector's SMTP server using 0 to 255 for each address field. Do not use these addresses: 127.x.x.x, 192.0.2.x or 224.0.0.0 through 255.255.255.
Projector Network Settings - Network Menu Network Menu - Reset Menu Settings on the Reset menu let you reset all of the network settings. s Network > Network Configuration > Reset Setting Options Description Reset network settings. Yes No Select Yes to reset all network settings.
Projector Setup Settings - ECO Menu Settings on the ECO menu let you customize projector functions to save power. Setting Options Description Light Optimizer On Off When set to On, the lamp brightness is adjusted according to the projected image. This helps to reduce the power consumption by lowering the lamp brightness according to the scene being projected. The setting is stored for each Color Mode. This item is enabled when: • Power Consumption is set to Normal. • Auto Iris is set to Off.
Projector Setup Settings - ECO Menu a • When the Sleep Mode Timer setting is enabled, the lamp dims for a short time before the timer limit is reached and the projector turns off. • When the Lens Cover Timer or A/V Mute Timer settings are enabled, the lamp uses less power when the lens cover is closed or A/V Mute is activated.
Projector Information Display - Info Menu You can display information about the projector and version by viewing the Info menu. However, you cannot change any settings in the menu. 117 Info Menu - Projector Info Menu You can display information about the projector and input sources by viewing the Projector Info menu in the projector's Info menu. Information item Description Projector Info Displays the projector information. Version Displays the projector's firmware version.
Projector Information Display - Info Menu Information item Description Video Signal Displays the video signal format of the current input source. Refresh Rate Displays the refresh rate of the current input source. Sync Info Displays information that may be needed by a service technician. Status Displays information about projector problems that may be needed by a service technician. Serial Number Displays the projector's serial number.
Projector Information Display - Info Menu Event ID code Cause and solution 0893 The WEP/TKIP/AES encryption type does not match. Make sure the wireless network security settings are correct. 0894 Communication with an unauthorized access point was disconnected. Contact your network administrator. 0898 Failed to acquire DHCP. Make sure the DHCP server is operating correctly. If you are not using DHCP, set the DHCP setting to Off in the projector's Network menu.
Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset menu. Setting Options Description Reset Lamp Hours — Reset the projector's lamp usage timer to zero when you replace the lamp. Reset All Config — Resets most of the projector settings to their default values.
Copying Menu Settings Between Projectors (Batch Setup) After selecting the projector's menu settings for one projector, you can use the following methods to copy the settings to other projectors, as long as they are the same model. • by using a USB flash drive • by connecting a computer and projector using a USB cable Menu settings such as the following are not copied to the other projector.
Copying Menu Settings Between Projectors (Batch Setup) the USB flash drive containing the saved batch setup file to the g Connect projector's USB-A port. down the [Menu] button on the remote control or the control h Hold panel and connect the power cord to the projector. all of the projector's indicators turn on, release the [Menu] i When button. When all of the indicators start flashing, the settings are being written. When writing is finished, the projector turns off.
Copying Menu Settings Between Projectors (Batch Setup) the batch setup file (PJCONFDATA.bin) that you saved to your l Copy computer to the top level folder of the removable disk. a Indicator status • Lamp: Orange - flashing fast • Temp: Orange - flashing fast Writing the settings may have failed and an error may have occurred in the projector's firmware. Stop using the projector, remove the power plug from the electrical outlet. Contact Epson for help. When writing is finished, the projector turns off.
Maintaining the Projector You may need to clean the projector's lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation. The only parts you should replace are the lamp, air filter, and remote control batteries. If any other part needs replacing, contact Epson or an authorized Epson servicer. Warning Before cleaning any part of the projector, turn it off and unplug the power cord.
Cleaning the Lens Clean the projector's lens periodically, or whenever you notice dust or smudges on the surface. • To remove dust or smudges, gently wipe the lens with lens-cleaning paper. • To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Cleaning the Projector Case Before cleaning the projector case, turn off the projector and unplug the power cord. • To remove dust or dirt, use a soft, dry, lint-free cloth. • To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector. Attention Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the projector case. These can damage the case. Do not use canned air, or the gases may leave a flammable residue.
Air Filter and Vent Maintenance Regular filter maintenance is important to maintaining your projector. Clean the air filer when a message appears telling you the temperature inside the projector has reached a high level. It is recommended that you clean these parts over a 6000-hour period. Clean them more often than this if you use the projector in a particularly dusty environment.
Air Filter and Vent Maintenance b Open the air filter cover. 128 c Pull the air filter out of the projector. a Dispose of used air filters according to local regulations.
Air Filter and Vent Maintenance the new air filter in the projector as shown and push gently until d Place it clicks into place. e Close the air filter cover. g Related Links • "Replacement Parts" p.
Projector Lamp Maintenance The projector monitors the number of hours the lamp is used and displays this information in the projector's menu system.
Projector Lamp Maintenance the screwdriver included with the replacement lamp to loosen the c Use screw securing the lamp cover. 131 d Slide the lamp cover out and lift it off. Warning When replacing the lamp, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is cracked, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently.
Projector Lamp Maintenance f Grip the raised section of the lamp and remove it. 132 Attention Do not touch any glass on the lamp assembly to avoid premature lamp failure. h Push in the lamp firmly and tighten the screws to secure it. a • If you notice the lamp is cracked when removing the lamp, contact Epson for help. • The lamp(s) in this product contain mercury (Hg). Check your local laws and regulations regarding disposal or recycling. Do not put in the trash.
Projector Lamp Maintenance a • Make sure the lamp cover is securely installed or the lamp will not turn on. • Do not replace the lamp cover with too much force and make sure the lamp cover is not deformed. 133 d Select Reset Lamp Hours and press [Enter]. Reset the lamp timer to zero to monitor the new lamp's usage. g Related Links • "Replacement Parts" p.
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Attention Make sure you read the Safety Instructions before handling the batteries. a Remove the battery cover as shown. b Remove the old batteries. c Insert the batteries with the + and – ends facing as shown. 134 Warning Check the positions of the (+) and (–) marks inside the battery holder to ensure the batteries are inserted the correct way.
Solving Problems Check the solutions in these sections if you have any problems using the projector. g Related Links • "Projection Problems" p.136 • "Projector Indicator Status" p.137 • "Using the Projector Help Displays" p.139 • "Solving Image or Sound Problems" p.140 • "Solving Projector or Remote Control Operation Problems" p.146 • "Solving Network Problems" p.
Projection Problems If the projector is not working properly, turn it off, unplug it, and then plug it back in and turn it on. If this does not solve the problem, check the following: • The indicators on the projector may indicate the problem. • The projector's Help system can display information about common problems. • The solutions in this manual can help you solve many problems. If none of these solutions help, contact Epson for technical support.
Projector Indicator Status The indicators on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the indicators and then refer to this table for a solution. a • If the indicators display a pattern not listed in the table below, turn the projector off, unplug it, and contact Epson for help.
Projector Indicator Status 138 Indicator and status Problem and solutions Indicator and status Problem and solutions Power: Off Status: Flashing blue Lamp: Lit orange Temp: Off Lamp has a problem. • Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary. • Clean the air filter. • If operating the projector at high altitude, set the High Altitude Mode setting to On in the projector's Extended menu.
Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 139 the up and down arrow buttons to highlight the problem you want d Use to solve. a Turn on the projector. b Press the [Home] button on the control panel or remote control. e Press [Enter] to view the solutions. one of the following actions when you are finished. f Perform • To select another problem to solve, press [Esc]. c Select Help on the Home screen.
Solving Image or Sound Problems Check the solutions in these sections if you have any problems with projected images or sound. g Related Links • "Solutions When No Image Appears" p.140 • "Solutions When Image is Incorrect Using the USB Display Function" p.141 • "Solutions When "No Signal" Message Appears" p.141 • "Solutions When "Not Supported" Message Appears" p.142 • "Solutions When Only a Partial Image Appears" p.142 • "Solutions When the Image is not Rectangular" p.
Solving Image or Sound Problems Solutions When Image is Incorrect Using the USB Display Function If no image appears or if the image appears incorrectly using the USB Display function, try the following solutions: • Press the [USB] button on the remote control. • Make sure the Epson USB Display software has been installed correctly. Depending on your OS or computer settings, the software may not have been installed automatically. Download the latest software from the following Web site and install it.
Solving Image or Sound Problems enabled and extended desktop mode is disabled. (See your computer or Windows manual for instructions.) d If necessary, check your video card settings and set the multiple display option to Clone or Mirror. Displaying From a Mac Laptop If the message "No Signal" is displayed when projecting from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.) a Open the System Preferences utility and select Displays.
Solving Image or Sound Problems 143 s Settings > Keystone > H/V-Keystone > Auto V-Keystone • Turn on horizontal keystone slider in the projector's Settings menu. Then adjust the slider until the image is evenly rectangular. s Settings > Keystone > H/V-Keystone > H-Keystone Adjuster • If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape. • Adjust the Quick Corner setting to correct the image shape.
Solving Image or Sound Problems • If you are projecting from a computer, press the [Auto] button on the remote control to automatically adjust the tracking and sync. If any bands or overall blurriness remain, display a uniformly patterned image on the screen and manually adjust the Tracking and Sync. settings in the projector's Signal menu. • If you are projecting from a computer, use a lower resolution or select a resolution that matches the projector's native resolution.
Solving Image or Sound Problems • If the volume for the computer is set to the minimum while the projector is set to the maximum, the noise may be mixed. Turn up the computer's volume and turn down the projector's volume. (When you use Epson iProjection (Windows/Mac) or USB Display.) g Related Links • "Projector Connections" p.19 • "Controlling the Volume with the Volume Buttons" p.
Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control. g Related Links • "Solutions to Projector Power or Shut-Off Problems" p.146 • "Solutions to Problems with the Remote Control" p.146 • "Solutions to Password Problems" p.
Solving Projector or Remote Control Operation Problems g Related Links • "Remote Control Operation" p.27 • "Projector Feature Settings - Settings Menu" p.104 • "Selecting the Projector You want to Operate" p.70 • "Replacing the Remote Control Batteries" p.134 Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control.
Solving Network Problems Check the solutions in these sections if you have problems using the projector on a network. g Related Links • "Solutions When You Cannot Access the Projector Through the Web" p.148 • "Solutions When Network Alert E-Mails are not Received" p.148 • "Solutions When the Image Contains Static During Network Projection" p.148 • "Solutions When You Cannot Connect Using Screen Mirroring" p.149 • "Solutions When the Image or Sound Contains Static During Screen Mirroring Connection" p.
Solving Network Problems • If the wireless connection is slow or your projected image contains noise, check for interference from other equipment, such as a Bluetooth device or microwave. Move the interfering device farther away or expand your wireless bandwidth. • Reduce the number of connected devices if the connection speed declines.
Appendix Check these sections for the technical specifications and important notices about your projector. g Related Links • "Optional Accessories and Replacement Parts" p.151 • "Screen Size and Projection Distance" p.153 • "Supported Monitor Display Resolutions" p.157 • "Projector Specifications" p.159 • "External Dimensions" p.161 • "USB Display System Requirements" p.163 • "List of Safety Symbols (corresponding to IEC60950-1 A2)" p.164 • "Glossary" p.166 • "Notices" p.
Optional Accessories and Replacement Parts The following optional accessories and replacement parts are available. Please purchase these products as and when needed. The following list of optional accessories and replacement parts is current as of: April 2017. Details of accessories are subject to change without notice and availability may vary depending on the country of purchase. g Related Links • "Screens" p.151 • "Cables" p.151 • "Mounts" p.151 • "For Wireless Connection" p.151 • "External Devices" p.
Optional Accessories and Replacement Parts External Devices Document Camera ELPDC21/ELPDC13/ELPDC07 Use when projecting image such as books, OHP documents, or slides. Soft carrying case ELPKS69 Use this to carry the projector by hand. Replacement Parts Lamp unit ELPLP96 Use as a replacement for used lamps. Air filter ELPAF32 Use as a replacement for used air filters.
Screen Size and Projection Distance 153 Check the table here to determine how far to place the projector from the screen based on the size of the projected image.
Screen Size and Projection Distance 16:9 screen size A 154 4:3 screen size B Minimum (Wide) to Maximum (Tele) A B Minimum (Wide) to Maximum (Tele) 30" 66 × 37 90 - 110 -2 29" 59 × 44 90 - 109 -4 35" 78 × 44 105 - 129 -2 30" 61 × 46 94 - 113 -4 40" 89 × 50 121 - 148 -2 40" 81 × 61 126 - 152 -5 50" 111 × 62 152 - 185 -3 50" 102 × 76 158 - 190 -7 60" 133 × 75 183 - 223 -3 60" 122 × 91 190 - 229 -8 70" 155 × 87 214 - 261 -4 70" 142 × 106 222 - 267 -10 80"
Screen Size and Projection Distance 155 XGA (EB‑‑X41/EB‑‑X05/EB‑‑X140/EB‑‑X450/EB‑‑X400) 4:3 screen size A 16:10 screen size 30" 61 × 46 89 - 107 -5 40" 81 × 61 119 - 143 -7 50" 102 × 76 150 - 180 -8 60" 122 × 91 180 - 217 -10 80" 163 × 122 241 - 290 -14 100" 203 × 152 302 - 363 -17 150" 305 × 229 454 - 546 -25 200" 406 × 305 607 - 729 -34 250" 508 × 381 759 - 912 -42 300" 610 × 457 912 - 1095 -51 A B 16:9 screen size B Minimum (Wide) to Maximum (Tele) B Mi
Screen Size and Projection Distance 16:9 screen size 156 A B Minimum (Wide) to Maximum (Tele) Minimum (Wide) 28" 62 × 35 89 - 121 1 30" 66 × 37 96 - 130 1 50" 111 × 62 161 - 218 1 60" 133 × 75 193 - 262 2 70" 155 × 87 226 - 306 2 80" 177 × 100 258 - 349 2 100" 221 × 125 323 - 437 3 150" 332 × 187 486 - 657 4 200" 443 × 249 649 - 877 5 300" 664 × 374 974 8 320" 708 × 399 1040 9 A B Minimum (Wide) to Maximum (Tele) Minimum (Wide) 16:10 screen size 29" 63
Supported Monitor Display Resolutions 157 The table here list the compatible refresh rate and resolution for each compatible video display format.
Supported Monitor Display Resolutions HDMI Port Input Signals 158 MHL Input Signal (EB‑‑U42/EB‑‑W42/EB‑‑W41/EB‑‑U05/EB‑‑U140) Signal Refresh rate (Hz) Resolution (dots) Signal Refresh rate (Hz) Resolution (dots) VGA 60 640 × 480 VGA 60 640 × 480 SVGA 60 800 × 600 SDTV (480i/480p) 60 720 × 480 XGA 60 1024 × 768 SDTV (576i/576p) 50 720 × 576 WXGA 60 1280 × 800 HDTV (720p) 50/60 1280 × 720 60 1366 × 768 HDTV (1080i) 50/60 1920 × 1080 WXGA+ 60 1440 × 900 HDTV (1080p) 24
Projector Specifications Product name EB‑U42/EB‑W42/EB‑W41/EB‑X41/EB‑S41/EB‑U05/EB‑W05 /EB‑X05/EB‑S05/EB‑U140/EB‑W140/EB‑X140/EB‑S140/EB‑ X450/EB‑X400/EB‑S400 Dimensions EB‑‑U42/EB‑‑U05/EB‑‑U140: 302 (W) × 87 (H) × 249 (D) mm (not including raised section) EB‑‑W42/EB‑‑W41/EB‑‑X41/EB‑‑S41/EB‑‑W05/EB‑‑X05/EB‑‑S0 5/EB‑‑W140/EB‑‑X140/EB‑‑S140/EB‑‑X450/EB‑‑X400/EB‑‑S40 0: 302 (W) × 77 (H) × 234 (D) mm (not including raised section) LCD panel size EB‑‑U42/EB‑‑U05/EB‑‑U140: 0.
Projector Specifications Power consumption (220 to 240 V area) EB‑‑U42: Operating: 298 W Standby power consumption (Communication On): 2.2 W Standby power consumption (Communication Off): 0.2 W EB‑‑W42/EB‑‑W41/EB‑‑X41/EB‑‑S41/EB‑‑W05/EB‑‑X05/EB‑‑S0 5/EB‑‑W140/EB‑‑X140/EB‑‑S140/EB‑‑X450/EB‑‑X400/EB‑‑S40 0: Operating: 282 W Standby power consumption (Communication On): 2.0 W Standby power consumption (Communication Off): 0.2 W EB‑‑U05/EB‑‑U140 Operating: 298 W Standby power consumption (Communication On): 2.
External Dimensions EB‑‑U42/EB‑‑U05/EB‑‑U140 EB‑‑W42/EB‑‑W41/EB‑‑X41/EB‑‑S41/EB‑‑W05/EB‑‑X05/EB‑‑S05/EB‑‑W140/EB‑‑ X140/EB‑‑S140/EB‑‑X450/EB‑‑X400/EB‑‑S400 A Center of lens B Distance from center of lens to suspension bracket fixing point 161 EB‑‑U42/EB‑‑U05/EB‑‑U140
External Dimensions EB‑‑W42/EB‑‑W41/EB‑‑X41/EB‑‑S41/EB‑‑W05/EB‑‑X05/EB‑‑S05/EB‑‑W140/EB‑‑ X140/EB‑‑S140/EB‑‑X450/EB‑‑X400/EB‑‑S400 The unit in these illustrations is mm.
USB Display System Requirements To use the projector's Epson USB Display software, your computer must meet the following system requirements. Requirement Windows Operating system Windows Vista • Ultimate (32-bit) • Enterprise (32-bit) • Business (32-bit) • Home Premium (32-bit) • Home Basic (32-bit) Windows 7 • Ultimate (32- and 64-bit) • Enterprise (32- and 64-bit) • Professional (32- and 64-bit) • Home Premium (32- and 64bit) • Home Basic (32-bit) • Starter (32-bit) Mac OS X • 10.7.
List of Safety Symbols (corresponding to IEC60950-1 A2) 164 The following table lists the meaning of the safety symbols labeled on the equipment. No. Symbol mark Approved standards Description No. Symbol mark Approved standards Description I — The same as No.8. A IEC60417 No.5007 "ON" (power) To indicate connection to the mains. J IEC60417 No.5001B B IEC60417 No.5008 "OFF" (power) To indicate disconnection from the mains. Battery, general On battery powered equipment.
List of Safety Symbols (corresponding to IEC60950-1 A2) No. Symbol mark Approved standards Description Q IEC60417 No.5172 Class II equipment To identify equipment meeting the safety requirements specified for Class II equipment according to IEC 61140. R ISO 3864 General prohibition To identify actions or operations that are prohibited. S ISO 3864 Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment.
Glossary 166 This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications. Aspect Ratio The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens. SDTV and general computer displays have an aspect ratio of 4:3. HDMI™ An abbreviation for High Definition Multimedia Interface.
Glossary 167 SDTV An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV High-Definition Television. SNMP An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and computers connected to a TCP/IP network.
Notices 168 Check these sections for important notices about your projector. Model: H838C/H839C/H840C/H841C/H842C/H843C/H844C/H845C/H846C g Related Links • "FCC Compliance Statement" p.168 • "Indication of the manufacturer and the importer in accordance with requirements of EU directive" p.169 • "Restriction of Use" p.169 • "Operating System References" p.169 • "Trademarks" p.169 • "Copyright Notice" p.170 • "Copyright Attribution" p.
Notices Indication of the manufacturer and the importer in accordance with requirements of EU directive Manufacturer: SEIKO EPSON CORPORATION Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan Telephone: 81-266-52-3131 http://www.epson.com/ Importer: EPSON EUROPE B.V. Address: Atlas Arena, Asia Building, Hoogoorddreef 5,1101 BA Amsterdam Zuidoost The Netherlands Telephone: 31-20-314-5000 http://www.epson.
Notices MHL, the MHL logo, and Mobile High-Definition Link are the trademarks or registered trademarks of MHL and LLC in the United States and/or other countries. "QR Code" is a registered trademark of DENSO WAVE INCORPORATED. Intel® is a registered trademark of Intel Corporation in the U.S. and/or other countries. Miracast™ and Wi-Fi Protected Setup™ are trademarks of the Wi-Fi Alliance.