ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors ESC/VP21 Command User’s Guide for Business Projectors
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Table of Contents 1. Introduction to ESC/VP21.................................................................................................................................. 3 2. ESC/VP21 Command Formats........................................................................................................................... 4 3. Applicable models ......................................................................
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 1. Introduction to ESC/VP21 ESC/VP21 is a control command and protocol for Epson projectors, which is used for A/V controller to control and monitor Epson projectors. The command codes are comprised of ASCII codes. Therefore the command codes can be understood very easily and you can easily control projectors using a PC with a terminal emulator such as Microsoft Hyper terminal.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 2. ESC/VP21 Command Formats 2.1. Set command format A set command consists of a command and a parameter. Projector returns a colon after executing the command. There are two types of parameters. One is fixed such as ON, OFF, or 21. Other is a step parameter such as INC, DEC or INIT. INC: increments the parameter by one. DEC: decrements the parameter by one. INIT: initializes the parameter. 2.2.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 4. Projector state and commands 4.1. Standby state (Operation indicator is in orange) When a projector is in a standby state, executable commands depends on projector models and standby configuration (network on, network off). Refer to the following table.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 5. Command transmission timing 5.1. Standby state 1). For all mode with the standby configuration of “network on” The first command can be sent anytime and the subsequent commands should be sent after receiving a colon from the projector. 2). Other than 1) PWR ON can be sent any time. 5.2. Power on state A command should be sent after receiving the colon of the previous command from the projector.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 6. Error Status A projector returns the error status when a projector receives "ERR?" command. The following projectors can return the error status while the projectors become the error status after cooling down. EMP-1700/1705/1710/1715, 6000/6100/6110/6010, 1815/1810/1825, S5/X5/83/ EB-G5000/G5100/G5150/G5200W/G5300/G5350 And later models.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 7. Command list and applicable models 7.1.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Function Power Input source PinP setting A/V Mute Screen Command PWR SOURCE PINP MSEL AUTOKEYSTONE Auto Keystone G5350 G5300 G5200W G5150 G5100 G5000 S6/S62 X6/ W6 1735W/ 1730W/ 1725/ 1720 84/85/ 824/825 826W Z8000WU Z8050W S7/X7/ W7 S8 X8/ W8 1910/ 1915/ 1920W/ 1925W O O O O O O O O O O O O O O O O O O O O O O O O O O O - - O O - X6,W6 Only Aspect setting Color mode Lamp hour Brightness level A
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 7.2.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 8. Command Details 8.1. Command table 1 (Fixed parameter) Set commands PWR xx Get commands PWR? Parameter for set (Return code for get) ON OFF 00: “Standby” as the time of “Network off” Models Function All models Power ON/OFF 61/81, 830/835, 740/745/732/737 760/765, 821/828, 7900/7950.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands SOURCE xx Get commands SOURCE? Parameter for set (Return code for get) 11: PC1 (analog RGB) 12: PC1 (digital RGB) 13: PC1 (RGB-Video) 21: PC2 (analog RGB) 22: PC2 (RGB-Video) 23: Component Video (YCbCr) 24: Component Video (YPbPr) 41: Video (RCA) 42: Video (S) 11: RGB 14: Input1 (YCbCr) 15: Input1 (YPbPr) 40: Video 41: Video (RCA) 42: Video (S) 50: EasyMP 10: INPUT1 (D-Sub) 11: INPUT1 (analog RGB) 13: INPUT1
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands SOURCE xx Get commands SOURCE? Parameter for set (Return code of get) 10: Input 1 11: Input 1 (RGB) 14: Input 1 (Component) 20: Input 2 21: Input 2 (RGB) 24: Input 2 (Component) 40: Video 41: Video (RCA) 42: Video (S) 10: Input 1 11: Input 1 (RGB) 14: Input 1 (Component) 30: HDMI (W6 only) 40: Video 41: Video (RCA) 42: Video (S) 50: EasyMP 51: USB Display 52: Slideshow 10: INPUT1 (D-Sub) 11: INPUT1 (RGB) 14:
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands SOURCE xx Get commands SOURCE? Parameter for set (Return code of get) 10: INPUT1 11: INPUT1 (RGB) 14: INPUT1 (Component) 20: INPUT2 (D-Sub) 21: INPUT2 (RGB) 24: INPUT2 (Component) 40: Video 41: Video (RCA) 42: Video (S) 51: EasyMP (USB Display) 52: EasyMP (USB 85/824/825/826W only) 53: EasyMP (LAN 85/825/826W only) 10: INPUT1 11: INPUT1 (RGB Analog) 14: INPUT1 (Component) 24: INPUT2 (Component) 30: INPUT3 (DVI
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands Get commands SOURCE xx SOURCE? PINP [source posX posy size] (Ex) PINP 42_1_ 2_ 1 ? PINP xx MSEL xx ? MSEL? AUTOKEYSTONE xx AUTOKEYSTONE? Parameter for set (Return code of get) 10: INPUT1 11: INPUT1 (RGB) 14: INPUT1 (Component) 20: INPUT2 21: INPUT2 (RGB) 24: INPUT2 (Component) 40: Video 41: Video (RCA) 42: Video (S) 51: USB Display 52: USB 53: LAN Source: Video source of sub-screen (Video or S-video) p
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands ASPECT xx Parameter for set (Return code of get) Get commands ASPECT? 10:4:3 12: zoom 4:3 20: 16:9 10:4:3 20: 16:9 Input signal is PC 00: Normal 10: 4:3 20: 16:9 Input signal is Component/S-Video.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands Get commands ASPECT xx ASPECT? CMODE xx CMODE? Parameter for set (Return code of get) Input signal is PC 00: Normal 10: 4:3 20: 16:9 Input signal is video 10: 4:3 20: 16:9 Input signal is HDMI 10: 4:3 20: 16:9 30: Auto 01: sRGB 02: Normal 03: Meeting 04: Presentation 05: Theatre 06: Game 01: sRGB 04: Presentation 05: Theatre 08: Dynamic 01: sRGB 04: Presentation 05: Theatre 06: Living Room 08: Dynamic 01:
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands CMODE xx Get commands CMODE? Parameter for set (Return code of get) 01: sRGB 03: Presentation2 04: Presentation 05: Theatre 06: Dynamic 08: Sports 10: Custom 11: Black Board 14: Photo 01: sRGB 03: Presentation2 04: Presentation 05: Theatre 06: Dynamic 08: Sports 11: Black Board 14: Photo 01: sRGB 04: Presentation 05: Theatre 06: Dynamic 08: Sports 11: Black Board 12: White Board 14: Photo 01: sRGB 04: Presenta
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands LUMINANCE xx Parameter for set (Return code of get) Get commands LAMP? LUMINANCE? 0 ~ 65535 00: High 01: Low 00: Normal 01: Eco Models All models 73/53/74/54, 7800/7850 8300/8350/9300, 61/81 830/835, 740/745, 821 7900/7950, 732/737, S3/S4 760/765, 755/750, 82, 6100 1715/1710/1705/1700 1815/1810/1825, X5/822/823 G5350/G5100/G5200W S6/X6/W6 1735W/1730W/1725/1720 84/85/824/825/826W Z8000WU/Z8050W S7/X7/W7/S8/X
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Set commands FLWARNING xx Parameter for set (Return code of get) Get commands FLWARNING? FLTIME x1 x2 FILTER? ZOOM ZOOM? FOCUS FOCUS? LENS LENS? HLENS HLENS? Models Function 00: ON 01: OFF 6100/6110 Display setting of warning time of Air filter x1: Object of setting 00: All objects 01: Object 1 02; Object 2 03: Object 3 x2: Set time 0: １~ 100(100H) 1: 101~ 200 (200H) l 14: 1401 ~ 9999 (1500H)* 0 ~ 65535 6100/6
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 8.2.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors Initial value Set commands TINT xx 0 Steps -32 ~ 32 -15 ~ 15 VKEYSTONE xx 0 -5 ~ 5 -90 ~ 90 -80 ~ 80 -64 ~ 64 -60 ~ 60 HKEYSTONE xx 0 -60 ~ 59 -30 ~ 30 -64 ~ 64 -60 ~ 60 -40 ~ 40 -39 ~ 39 -29 ~ 29 Models 30/52, 73/53/74/54 S1/S1H, 61/81, S3, 82 740/745/732/737/760/765/755/750 S4, 6100, 1715/1710/1705/1700 1815/1810/1825, X5/822/823 G5350/G5100/G5200W 400W/410W, S6/X6/W6 1735W/1730W/1725/1720 84/85/824/825/826W Z80
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 9. Appendix 9.1. Communication specification A projector and a computer can be connected using a serial or USB port. The projector can be remotely controlled by sending commands to the projector.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors ■ USB connection (600/800/810/811/820, 720/730/520, 73/53/74/54, 735, 8300/9300, 7800/7850, 61/81, 830/835, 740/745/732/737/760/765, 821/828, 7900/7950, S3/S4, 755/750, 62/82/X3, 1715/1710/1705/1700, S5/X5/EX90,260, G5350/G5150, S6/X6/W6, 1735W/1730W/1725/1720, S7/X7/W7, S8/X8/W8, 1925W/1920W/1915/1910) ・ For 600/800/810/811/820, 74/54, select USB at advanced setting of the Menu.
ビジネスプロジェクター用 ESC/VP21 Command User’sESC/VP21 Guide forコマンド使用ガイド Business Projectors 10. Revision History Revision A B Issued date Sep 16, 2005 Oct 19, 2005 Page All pages All pages C D E F G H I Nov 4, 2005 Apr 17, 2006 Aug 11, 2006 Mar 19, 2007 Jun 4, 2007 Dec 21, 2007 Apr 23, 2008 All pages All pages All pages All pages All pages All pages All pages J K L Sep 19, 2008 Feb 25, 2009 Mar 25, 2009 All pages All pages All pages M Oct 9, 2009 All pages Description First release.
