designer.book Page i Wednesday, August 22, 2001 2:03 PM Fiery Spark™ Designer Getting Started Printed on recycled paper.
designer.book Page ii Wednesday, August 22, 2001 2:03 PM ii | Copyright © 2001 by Epson America, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with these EPSON printers.
designer.book Page iii Wednesday, August 22, 2001 2:03 PM | iii Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Client . . .
designer.book Page 1 Wednesday, August 22, 2001 2:03 PM Introduction This guide provides basic installation instructions for the Fiery Spark™ Designer software in a client-server configuration. This configuration allows you to send print jobs to the printer from multiple Macintosh® computers configured over the network. For instructions on using the Fiery Spark software, see the User Guide on the Fiery Spark CD-ROM. This manual is in PDF format.
designer.book Page 2 Wednesday, August 22, 2001 2:03 PM 2 | Getting Started System Requirements Before you install the software, make sure your computer meets the minimum system requirements listed below: Server • Macintosh G3, G4, or iMac™ (G4 recommended) • System 8.6 to 9.x (9.
designer.book Page 3 Wednesday, August 22, 2001 2:03 PM Software Installation | 3 Software Installation Note Do not install the hardware key until after all the software is installed.
designer.book Page 4 Wednesday, August 22, 2001 2:03 PM 4 | Getting Started Installing Mac OS Runtime for Java (MRJ) You need to install Mac OS Runtime for Java (MRJ) 2.2.0 or later to run Fiery Spark. If you have an older version of MRJ, you need to uninstall that version and install version 2.2.4 from the Fiery Spark CD-ROM. Follow these steps: 1. On the Fiery Spark CD-ROM, open the Software > Fiery Spark folder. Installer icon in the MRJ folder. 2. Double-click the 3.
designer.book Page 5 Wednesday, August 22, 2001 2:03 PM Installing Screen Fonts | 5 Installing Screen Fonts The Fonts installer on the Fiery Spark CD-ROM includes screen and printer fonts that correspond to the 136 built-in PostScript printer fonts on the Fiery Spark. The Fonts installer copies both kinds of fonts to the System > Fonts folder on your hard drive. To be available to applications, the screen fonts must remain in this folder. The printer fonts can be copied to a folder of your choice.
designer.book Page 6 Wednesday, August 22, 2001 2:03 PM 6 | Getting Started Selecting Fiery Spark in the Chooser Before you print, select AdobePS and Fiery Spark from the Chooser, then close the Chooser. For instructions on using the Fiery Spark software, see the User Guide on the Fiery Spark CD-ROM. Hardware Key Installation After the software is installed, connect the hardware key to an available USB port on the server computer.
designer.book Page 7 Wednesday, August 22, 2001 2:03 PM Warranty | 7 WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device.
designer.book Page 8 Wednesday, August 22, 2001 2:03 PM 8 | Getting Started on the second business day. To secure the replacement of the key, you must provide Epson with a valid credit card number with sufficient credit to cover the price of the defective key. You will be billed at the Manufacturer’s Suggested Retail Price if the defective key is not returned to Epson within ten (10) business days of your call. TO RECEIVE A FREE REPLACEMENT KEY, YOU MUST BE ABLE TO PROVIDE EPSON WITH YOUR DEFECTIVE KEY.
