Wireless Mirroring Adapter EHDMC10 Copyright©2014 Seiko Epson Corporation. All rights reserved. 2014.
Introduction Thank you very much for purchasing this product. Make sure you read this guide before using the product to ensure you use it safely and correctly. Keep this guide in a safe place so that you can access it easily if you have any questions in the future. Safety Instructions This documentation uses graphical symbols to show how to use the product safely and avoid injury to others or damage to property. These symbols and their meanings are shown below.
Do not place vases, containers containing water, or medical containers on this product. If any liquid spills from the container, a fire or electric shock could occur. Take care when handling the power plug. If it is not handled correctly, a fire or electric shock could occur. Note the following points when handling the plug. • Do not overload wall outlets, extension cables, or power strips. • Do not plug it in if there are any foreign substances, such as dust, attached to the plug.
Except as indicated in the "User's Guide", the case for this product should only be opened by qualified service personnel. Do not disassemble or remodel this product or its consumables. Many sections inside the product carry a high electrical charge which could cause a fire or electric shock to occur. Caution When moving the product, make sure you turn off the power, unplug the power cable from the electrical outlet, and disconnect any wiring before moving. Otherwise, a fire or electric shock could occur.
For safety reasons, make sure you unplug the power cable from the electrical outlet when the product is not in use. If the insulation has degraded, a fire could occur. When using this product, make sure it is at least 22 cm (8 inches) away from your body. WARNING: This product contains chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. (This notice is provided in accordance with Proposition 65 in the Cal.
Included Items Wireless/ Wireless Wireless Pass-Thru Connect Ready Link Base unit micro USB cable AC adapter (Depend on country) An HDMI cable is not included. To connect an HDMI device, you need to obtain a commercially available HDMI cable. Parts and Functions Ports Reset button A B C micro USB port A Supplies power to this unit. Connect to an electrical outlet using the supplied micro USB cable and AC adapter.
Buttons and Indicators Slide switch A Changes between the Source and Sink functions. Wireless/Pass-Thru button B When sliding the switch to [Source]: Switches the output device between the MOVERIO BT-200 and the device connected to the HDMI Output. When sliding the switch to [Sink]: Switches the input device between the MOVERIO BT-200 and the device connected to the HDMI Input. Wireless Connect button C Attempts to connect again when a disconnection occurs.
Connections Sending images from a video device to your MOVERIO BT-200 (Source function) Connect a commercially available HDMI cable to the HDMI Input port on this unit and to the HDMI output port on the device that is sending images. Set the slide switch to Source. Image sending device Image receiving device Wireless/ Wireless Wireless Pass-Thru Connect Ready Link Preparing to Connect (Wireless Mirroring Adapter Operations) Press the Wireless/Pass-Thru button.
Connecting (MOVERIO BT-200 Operations) 1. Launch MOVERIO Mirror that comes preinstalled on MOVERIO BT-200. 2. Tap [Sink] on the MOVERIO Mirror main screen. 3. Tap [Target Device]. 4. Tap the Adapter Name (EHDMC1-XXXXXX) attached to this unit from the list of available devices. The status displayed below Adapter Name changes to [Invited], and connection starts. You see the following screen on the device connected to the HDMI Output port while connecting.
Receiving images from MOVERIO BT-200 to output to a television (Sink function) Connect a commercially available HDMI cable to the HDMI Output port on this unit and to the HDMI input port on the device that is receiving images. Image receiving device Image sending device Wireless/ Wireless Wireless Pass-Thru Connect Ready Link Preparing to Connect (Wireless Mirroring Adapter Operations) Press the Wireless/Pass-Thru button. The Wireless Ready indicator flashes for approximately one minute.
Connecting (MOVERIO BT-200 Operations) 1. Launch MOVERIO Mirror that comes preinstalled on MOVERIO BT-200. 2. Tap [Source] on the MOVERIO Mirror main screen. 3. Tap [Target Device]. 4. Tap the Adapter Name (EHDMC1-XXXXXX) attached to this unit from the list of available devices. The status displayed below Adapter Name changes to [Invited], and connection starts. You see the following screen on the device connected to the HDMI Output port while connecting.
Setting You can make settings from the MOVERIO BT-200 web browser or on your computer. 1. Hold down the Wireless/Pass-Thru button and the Wireless Connect button at the same time for at least five seconds. The unit enters setup mode and the IP address for the unit is displayed on the device connected to the HDMI Output. The Wireless Ready and Link indicators flash at the same time. 2. Enter the displayed IP address in the URL bar on your browser. The setup screen is displayed. 3.
Troubleshooting Cannot send or receive images • Check that the micro USB cable is connected correctly. • Check that the AC adapter is connected to the electrical outlet correctly. • Check that the devices are connected to the HDMI Input or the HDMI Output correctly. • Check that the input source of the device connected to the HDMI Output is switched to HDMI. • Check that you have selected the Sink or Source settings correctly for this unit and the MOVERIO BT-200.
No audio is output • Check the volume on the device that is playing the images. • When you receive images from MOVERIO BT-200, audio is output only when you use MOVERIO Mirror to play back images. See the MOVERIO BT-200 User’s Guide for more details.
Storage environ- Temperature: -10 to +60 °C (14 to 140 °F) ment Humidity: 10 to 90% (no condensation) Dimensions Mass 115 x 115 x 30 mm (4.5 x 4.5 x 1.1 inches) 150 g Wireless standard: IEEE 802.11b/g/n Wireless specifica- Frequency band: 2.4 GHz, 1-13 ch tions Modulation: OFDM and DS-SS Assumed interference distance: 10m (32.8 feet) Information on Supported Devices Visit the http://www.epson.com web site for information on devices that can send and receive image content using this product.
Wireless Telegraphy Act Regulations The following acts are prohibited by the Wireless Telegraphy Act. • Modifying and disassembling (including the antenna) • Removing the label of conformance Restriction of Use This product is manufactured based on the specifications of the country of sale. When using this product outside the country of sale, contact your nearest support center.
JIS C 61000-3-2 conformity This product conforms to the current "JIS C 61000-3-2" harmonic standard. DECLARATION of CONFORMITY According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We : Epson America, Inc.
more of the following measures. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numèrique de la classe B est conforme à la norme NMB-003 du Canada. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
