Wireless LAN unit User's Guide ELPAP03
Notations Used in This Guide f General information indications Attention q s Indicates procedures which may result in damage or injury if sufficient care is not taken. Indicates additional information and points which may be useful to know regarding a topic. Indicates a page where detailed information regarding a topic can be found. Procedure Indicates operating methods and the order of operations. The procedure indicated should be carried out in the order of the numbered steps.
Supplied Items List See the following check list to make sure that you have all of the supplied items. If anything is missing or damaged, please contact your dealer.
Safety Instructions Thank you very much for purchasing this product. Read this document carefully to use this unit safely and correctly. To allow you to solve any unknown points quickly, keep this information close to hand. So that you can use the product safely and correctly, symbols are applied in the documentation and on the product to indicate possible harm to the user or to others and the risk of damage to property. The indications and their meaning are as follows.
Precautions Notes on Handling and Storage • Do not store in locations with high temperatures or high humidity. It may in particular be damaged or deformed if left in a vehicle with the windows shut, or placed it locations with unusually high temperatures for extended periods such as in direct sunlight. • Do not get it wet. This may cause malfunctions to occur. • Do not use near microwave ovens. Wireless communication may be interrupted by electromagnetic interference generated by microwave ovens.
Precautions Notes on Security when Using Wireless LAN (Important information on customer rights (maintaining privacy)) The advantage of using a wireless LAN over a LAN cable is that, because information is exchanged using radio signals, you can easily connect to the network if you are within range of the radio signals.
Installing this Unit Installing Install this unit into the projector. 7 losing this unit and so on, make sure you C Tofix avoid it in place with the screw supplied. Procedure the cover for the projector's wireless LAN A Remove unit installation section. Screw hole for the Screw to fix the wireless LAN unit Reading the Wireless LAN Unit Access Lamp B Install this unit. There are two wireless LAN unit access lamps, one on top of the projector the other on this unit.
Installing this Unit : Flashing Status : Lit : Off The Projector's Indicator This Unit's Indicator Green Green This unit is not installed in the projector This unit is installed in the projector but not yet connected to the network This unit is installed in the projector and connected to the network This unit is installed in the projector, connected to the network, and communicating Green Green Green (Flashing quickly)
Steps for Connecting in "Quick Connection Mode" When this unit is installed in the projector, you can project computer images by wirelessly connecting the projector with a computer over a network. Type of Network Connection You can use the following two methods to connect a computer and the projector over a network by using EMP NS Connection found on the EPSON Projector Software for Meeting & Presentation CD-ROM supplied with the projector.
Steps for Connecting in "Quick Connection Mode" Steps before Connecting in "Quick Connection Mode" In the following illustration, you only need to perform the light blue sections the first time you connect.
Preparing the Computer To use "Quick Connection Mode" to connect the projector and the computer, you need to make the following settings on the computer. • Install EMP NS Connection You can find EMP NS Connection on the EPSON Projector Software for Meeting & Presentation CD-ROM supplied with the projector. If it is already installed, you do not need to install it again. See the documentation supplied with the projector for the installation method.
Connecting in "Quick Connection Mode" and Projecting Operating the Projector Before connecting, put the projector into connection standby status. 12 Operating the Computer In the following explanations, unless otherwise noted, Windows screens are used. You see the same screens even when using Macintosh. Procedure the [t] button on the remote control to turn A onPress the projector. Procedure A Start EMP NS Connection. For Windows B Press the [EasyMP] button on the remote control.
Connecting in "Quick Connection Mode" and Projecting the projector you want to connect to, and C Select then click "Connect". Projector Keyword is set to "On" from the D When projector, the keyword entry screen is displayed. Enter the keyword displayed on the EasyMP standby screen, and then click "OK". When the connection is complete, the computer's screen is projected. The following EMP NS Connection toolbar is displayed on the computer screen.
The Target Projector is Not Found Action 1. Restart the computer. Action 2. Check if the projector network settings are set to "Quick Connection Mode". See the documentation supplied with the projector for more details. Action 3. Check the following if actions 1 and 2 do not help. (If it is disconnected, check the following.) Is the indicator on the wireless LAN unit flashing? Not flashing Reinstall the wireless LAN unit.
Disconnecting There are two methods of disconnecting the projector and the computer. Disconnecting from the Computer Click the button on the toolbar. Disconnecting from the Projector Procedure A Press the [Esc] button on the remote control. "Exit", and then press the [Enter] button on B Select the remote control.
This Unit's General Specifications Conditions for Connecting to Compatible Wireless LAN Cards and Access Points This unit can be connected to the following products in accordance with IEEE 802.11g, 802.11b, and 802.11a. • Wireless LAN card • Computers with a built-in wireless LAN function • Access points However, you are unlikely to be able to make an ad hoc connection for wireless LAN equipment used with a computer in IEEE 802.11g. For details on wireless LAN equipment see the specifications.
DECLARATION of CONFORMITY According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: Tel: Epson America, Inc. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806 562-290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
