L R4C4450 Quick Reference Rev.C A5 size 7/18/00 Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ QUICK.FM Pass 0 Replacing Consumable Products 3. You must replace the following consumable products when a notice message appears on the LCD panel or in the EPSON Status Monitor 3 utility. See which color currently appears in the cartridge installation window. If you can see the color that you need to replace, go to step 5.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ 5. Turn the cartridge knob counterclockwise 90 degrees so that the O symbol on the knob is in the position shown below. By turning the knob, the cartridge extends slightly. 6. Pull the cartridge out of the slot. 7. Take a new cartridge out of its package, and gently shake it back and forth and front to back as shown below to distribute the toner evenly. R R4C4450 Quick Reference Rev.C A5 size 7/18/00 QUICK.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 QUICK.FM Pass 0 Replacing the photoconductor unit 1. Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ 4. Turn the small lever to the right. 5. Pull the photoconductor unit about 30 cm out of the printer. Turn off the printer. Note: Before replacing the photoconductor unit, be sure to turn off the printer. 2. 3. Open the front cover. Turn the large lever counterclockwise 90 degrees.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ 6. Hold the handle at the top of the photoconductor unit and gently pull it all the way out. A5 size 7/18/00 8. QUICK.FM Pass 0 Hold the handle on top of the photoconductor unit and place the unit on the guide rails. Insert it all the way into the printer. c 7. R R4C4450 Quick Reference Rev.C Caution: Be sure not to touch the surface of the drum.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ QUICK.FM Pass 0 10. Turn the large lever clockwise 90 degrees. 2. Grasp the handle and tab of the waste toner collector to release the lock. 3. Pull out the waste toner collector. 4. Take out a new waste toner collector. 11. Close the front cover. Replacing the waste toner collector 1. Open the front cover.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ 5. Hold the handle of the collector and insert it into the slot all the way until the tab clicks into place. 6. Close the front cover. A5 size 7/18/00 2. Pull down the Face-up Tray. 3. QUICK.FM Pass 0 Hold the handle of the fuser unit and pull it all the way out. w Replacing the fuser oil roll 1. R R4C4450 Quick Reference Rev.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 4. QUICK.FM Pass 0 Take a new fuser oil roll out of its box, and remove the cover and two shipping pins as shown below: Note: Do not touch the white roll surface. 5. Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ 6. Push the roll down firmly until it clicks into place. 7. Push the fuser unit into the printer until it clicks.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ Clearing Jammed Paper R R4C4450 Quick Reference Rev.C A5 size 7/18/00 QUICK.FM Pass 0 2. Remove the jammed or crumpled paper. If the paper is torn, be sure to remove all pieces. 3. Replace the paper in the paper cassette and close it. 4. Pull the paper path unit out slowly until it stops. Be careful not to tear the jammed paper.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ QUICK.FM Pass 0 5. Pull out the jammed paper from the bottom of the paper path unit. 6. Close the paper path unit firmly. 2. Pull the paper path unit out until it stops. Be careful not to tear the jammed paper. 3. Open the unit cover by grasping the handle and pulling up. Clearing the MP tray 1. Pull the jammed paper out gently.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ 4. 5. Turn the knob on the unit clockwise as shown below. The jammed paper should come out. After the jammed paper is ejected halfway, pull the paper up as shown below. R R4C4450 Quick Reference Rev.C A5 size 7/18/00 QUICK.FM Pass 0 6. Close the cover of the unit. 7. Close the paper path unit firmly.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 1. Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ QUICK.FM Pass 0 c Pull the fuser unit out gently until it stops. Be careful not to tear the jammed paper. Caution: ❏ Do not touch the fuser, which is marked CAUTION! HIGH TEMPERATURE, or the surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very hot. ❏ Reattach the fuser oil roll as soon as you clear any jammed paper.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ 4. Pull out the jammed paper. A5 size 7/18/00 1. Re-install the fuser oil roll. 6. Close the fuser unit firmly. QUICK.FM Pass 0 Clearing the output path cover c 5. R R4C4450 Quick Reference Rev.C Caution: When paper is jammed in the path to the face-down tray, clear it from the fuser unit. Do not pull jammed paper out from the face-down tray. Open the output path cover on the left side of the printer.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 2. Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ QUICK.FM Pass 0 Remove all jammed paper. If paper has jammed at the top of the output path, gently lift it out. If it has jammed near the bottom of the output path cover, carefully pull it out of the printer. 2. Pull the jammed paper out gently. Be careful not to tear the paper. 3. Close the feeder cover.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ Control Panel Messages Status message list Messages Description Form Feed The printer is feeding paper. Ready The printer is ready to print. Reset The printer's current interface has been reset and the buffer is cleared. Reset All All printer settings have been reset to the user default configuration, the last settings that were saved. Reset to Save You should reset the printer to save the current settings.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 QUICK.FM Pass 0 Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ Messages Description Messages Description Collate was disabled Printing by specifying the number of copies is no longer possible due to lack of memory or free space on the Hard Disk Drive. If this error occurs, print only one copy and end printing. Format Error ROM A/Format Error ROM B An unformatted ROM has been inserted.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ A5 size 7/18/00 QUICK.FM Pass 0 Messages Description Messages Description Image Optimum There is insufficient memory to print the page at the specified print quality. The printer automatically lowers the print quality so that it can continue printing. If the printout is not acceptable, try simplifying the page by limiting the number of graphics or reducing the number and sizes of fonts.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 QUICK.FM Pass 0 Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ Messages Description Messages Description Mem Overflow The printer has insufficient memory to execute the current task. To correct the error, press the Continue button on the control panel. If the message remains, reset the printer. You can also clear this message by turning the printer off, waiting 10 seconds, and then turning it back on.
Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ A5 size 7/18/00 QUICK.FM Pass 0 Messages Description Messages Description Print Overrun The required time to process the print data exceeds the print engine speed because the current page is too complex. Press the Continue button to resume printing. If this message appears again, turn on Page Protect in the SelecType Config menu. Replace Waste T Box The waste toner collector has become full.
L R4C4450 Quick Reference Rev.C A5 size 7/18/00 QUICK.FM Pass 0 Proof Sign-off: ABE K.Tsuno H.Kimura_______ H.Kimura _______ ABE J.Holmes _______ Messages Description Messages Description Warning Photocondctr The photoconductor unit is near the end of its service life. You can continue to print until there is no remaining service life but early replacement is recommended to maintain high print quality. XXXX Toner Crtg Out The indicated (XXXX) toner cartridge is not installed in the printer.
