BF Proof Sign-off: Nishi Grady _______ _______ Albatross Rev.
Proof Sign-off: Nishi Grady Albatross Rev.c _______ _______ A5 size 96/08/23 Front pass 0 title page ® Laser Printer All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein.
L Albatross Rev.c A5 size 96/08/23 Front pass 0 Declaration of Conformity According to ISO/IEC Guide 22 and EN 45014 Manufacturer: Address: SEIKO EPSON CORPORATION 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392 Japan Representative: Address: EPSON EUROPE B.V. Prof. J. H.
Albatross Rev.c A5 size 96/08/23 Front pass 0 Contents Getting Started About This Guide . . . . . . . . About Your Printer . . . . . . . Features . . . . . . . . . . . Options . . . . . . . . . . . . ENERGY STAR Compliance . . About Making Printer Settings . Printer Driver . . . . . . . . OneTouch modes . . . . . . SelecType . . . . . . . . . . Remote Control Panel utility Safety Information . . . . . . . . Ozone safety . . . . . . . . . Laser Printer Precautions . . . . Important Safety Instructions .
L Albatross Rev.c A5 size 96/08/23 Chapter 2 Front pass 0 Understanding Your Printer The Control Panel . Overview . . . . Display . . . . . Indicator lights Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2-2 2-3 2-4 2-5 Printer Options . . . . . . . . . . . . . . . . . Installing an Optional Paper Tray . . . . . . .
Albatross Rev.c A5 size 96/08/23 Chapter 4 Front pass 0 Remote Control Panel Utility Remote Control Panel Utility Overview . . . . . When to use the Remote Control Panel utility Installing the Remote Control Panel utility . Accessing the Remote Control Panel . . . . . LaserJet 4/EPSONScript Level 2 Mode . . . . ESCP2 Mode . . . . . . . . . . . . . . . . . . . FX Mode . . . . . . . . . . . . . . . . . . . . . I239X Mode . . . . . . . . . . . . . . . . . . . Page Setup Options . . . . . . . . . . . . . .
L Albatross Rev.c A5 size 96/08/23 Front pass 0 Using the OneTouch Modes . . . . . . . . Using Other Emulation Modes . . . . . . Changing emulation modes . . . . . . ESC/P 2 or FX Mode . . . . . . . . . . . . I239X Mode . . . . . . . . . . . . . . . . . EPSON GL/2 Mode . . . . . . . . . . . . . Before printing in EPSON GL/2 mode GL2 Menu . . . . . . . . . . . . . . . . Chapter 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Albatross Rev.c A5 size 96/08/23 Front pass 0 Appendix A Technical Specifications Paper . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . Printer . . . . . . . . . . . . . . . . . . . . . . . . . General . . . . . . . . . . . . . . . . . . . . . . Environmental . . . . . . . . . . . . . . . . . Mechanical . . . . . . . . . . . . . . . . . . . . Electrical . . . . . . . . . . . . . . . . . . . . . Interface . . . . . . . . . . . . . . . . . . . . . . . .
L Albatross Rev.c A5 size 96/08/23 Front pass 0 Appendix C Command Summary LaserJet 4 (LJ4) Emulation Commands GL/2 context commands . . . . . . ESC/P 2 and FX Commands . . . . . . ESC/P 2 mode . . . . . . . . . . . . FX mode . . . . . . . . . . . . . . . PJL Commands . . . . . . . . . . . . . I239X Emulation Commands . . . . . Page format . . . . . . . . . . . . . Text . . . . . . . . . . . . . . . . . . Auxiliary Functions . . . . . . . . . AGM Mode . . . . . . . . . . . . . . . . . . . . . . . . . .
Proof Sign-off: Nishi Grady _______ _______ Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 Getting Started The EPSON EPL-N2000 printer combines high performance and reliability with a wide range of features. To get started with your laser printer, please: ❏ Read the safety information, laser printer precautions, and important safety instructions in this section.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 Chapter 5, “SelecType,” contains detailed information on the settings you can make in SelecType. Read this chapter if you are not able to modify a printer setting from your software. Chapter 6, “Troubleshooting and Maintenance,” gives helpful information for what to do if you encounter a printer error and provides instructions on how to maintain your printer.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 About Your Printer Your printer is the latest in EPSON’s advanced line of laser printers. It emulates the Hewlett-Packard® LaserJet 4 (LJ4) printer, allowing you to print using the wide variety of software programs that support HP LaserJet printers.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 Toner Save Mode To reduce the amount of toner used in printing documents, you can print rough drafts by clicking the Toner Save box in the printer driver (explained in the next pages). Options Memory The printer comes with 4 MB of memory, which can be expanded up to 68 MB. Interface/Module The printer comes with two built-in bidirectional parallel interfaces and one built-in Ethernet interface.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 ENERGY STAR Compliance As an International ENERGY STAR Partner, EPSON has determined that this product meets the International ENERGY STAR Program guidelines for energy efficiency. The International ENERGY STAR Program promotes the voluntary development of energy-efficient computers, printers, and other peripheral equipment. About Making Printer Settings To print, you will need to make some printer settings.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 Printer Driver Use the printer driver to easily and conveniently make new printer settings. Most users may never need to use anything besides their application software and the printer driver to make printer settings. You can access the printer driver through an application‘s Print command or by choosing your printer in the Printers folder/program group in your operating system.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 Safety Information Laser safety This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This means that the printer does not produce hazardous laser radiation.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 Denmark Advarsel Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling. Klasse 1 laser produkt der opfylder IEC825 sikkerheds kravene. Finland and Sweden EPL-N2000 on lasertoiminen sivukirjoitin. Laserista ei aiheudu käyttäjälle vaaraa, kun kirjoitinta käytetään käyttöohjeiden mukaisesti.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 Norway Advarsel Dersom apparatet brukes på annen måte enn spesifisert i denne bruksanvisning, kan brukeren utsettes for unsynlig laserstråling som overskrider grensen for laser klasse 1. Dette er en halvleder laser. Maksimal effeckt til laserdiode er 5.0 × 10-3 W og bolgelengde er 785 +25 nm. −15 CDRH regulations The Center for Devices and Radiological Health (CDRH) of the U.S.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 Laser safety labels w Warning: Use of controls, adjustments, or performance of procedures other than those specified in this guide may result in hazardous radiation exposure. Your printer is a Class 1 laser product as defined in IEC 825 specifications. The label shown below is attached in countries where required. rg-1 Internal laser radiation Max. Radiation Power 8.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 For Denmark, Finland, Sweden, and Norway users An additional laser warning label is affixed to the inside of the printer, as shown below. rg-2 Ozone safety Ozone emission Ozone gas is generated by laser printers as a by-product of the printing process. Ozone is produced only when the printer is printing. Ozone exposure limit The recommended exposure limit for ozone is 0.
L Albatross Rev.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 ❏ Be careful not to touch the fuser, which is marked CAUTION Hot Surface Avoid Contact. If the printer has been in use, the fuser can be very hot. CAUTION Hot Surface Avoid Contact rg-3 ❏ Avoid touching the components inside the printer unless instructed to do so in this guide. ❏ Never force the printer’s components into place. Although the printer is designed to be sturdy, rough handling can damage it.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 ❏ Protect the light-sensitive drum from exposure to light. Avoid exposing the imaging cartridge to room light any longer than necessary. Do not open the drum’s protective cover. Overexposing the drum may cause abnormally dark or light areas to appear on the printed page and reduce the service life of the drum. rg-4 14 ❏ When handling the cartridge, always set it on a clean, smooth surface.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 ❏ Avoid touching the glass in front of the laser beam; otherwise, print quality may decline. rg-5 To get the best print quality, do not store the imaging cartridge in an area subject to direct sunlight, dust, salty air, or corrosive gasses (such as ammonia). Avoid locations subject to high temperatures or humidity or abrupt changes in temperature or humidity.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 Important Safety Instructions Read all of these instructions before operating your printer. 16 ❏ Follow all warnings and instructions marked on the printer. ❏ Unplug this printer from the wall outlet before cleaning. ❏ Use a damp cloth for cleaning and do not use liquid or aerosol cleaners. ❏ Do not use this printer near water. ❏ Do not place the printer on an unstable cart, stand, or table.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 ❏ Except as specifically explained in this guide, do not attempt to service this product yourself. Opening or removing those covers that are marked “Do Not Remove” may expose you to dangerous voltage points or other risks. Refer all servicing in those compartments to service personnel. ❏ Unplug this printer from the wall outlet and refer servicing to qualified service personnel under the following conditions: A.
L Albatross Rev.c Reference Guide A5 size Introduction ’96/08/23 pass 0 Safety information Warning: This appliance must be earthed. Refer to rating plate for voltage and check that the appliance voltage corresponds to the supply voltage.
Albatross Rev.c R Reference Guide A5 size Introduction ’96/08/23 pass 0 Warnings, Cautions, and Notes w c Warnings must be followed carefully to avoid bodily injury. Cautions must be observed to avoid damage to your equipment. Notes contain important information and useful tips on the operation of your printer.
L Albatross Rev.
Proof Sign-off: Nishi Grady Albatross Rev.c _______ _______ A5 size 96/08/23 R Chapter 1 Pass 0, DR Chapter 1 Paper Handling 1 Loading Paper . . . . . . . . . . . . . . Manually loading paper . . . . . . Selecting the paper size . . . . . . . Loading an uncommon paper size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1-2 1-5 1-6 Choosing Paper . Labels . . . . . Envelopes . . . Colored paper Transparencies . . .
L Albatross Rev.c A5 size 96/08/23 Chapter 1 Pass 0, DR Loading Paper This section covers how to manually load paper to check print quality after each page is printed and how to choose special media. To load paper normally, see your Getting Ready guide. To load paper in an optional lower paper tray, see page 3-3. Note: If the weight of your paper is not between 60 to 90 g/m2 (16 to 24 lb), decrease the number of sheets you load. Manually loading paper You can manually load paper in the MP Tray.
Albatross Rev.c A5 size 96/08/23 Chapter 1 Pass 0, DR To load paper manually, follow the steps below. 1. Access the printer driver menus in one of the following ways: Note: If you have not installed the printer driver, see your Getting Ready! guide for installation instructions. ❑ For access through your application software, click the Print or Printer Setup command in the File menu. You also may need to click Setup, Options, Properties, or a combination of these buttons.
L Albatross Rev.c A5 size 96/08/23 Chapter 1 Pass 0, DR 4. If the correct paper size is already loaded, skip to step 4. Otherwise, open the front cover, and remove any paper remaining in the MP Tray. Insert a sheet or stack of the correct size paper into the MP Tray with the printable side up, as far as it will go. Adjust the paper guides to match the paper size you are loading. r1-3 5. Send a print job from your application. The control panel display shows Manual Feed and the selected page size. 6.
Albatross Rev.c A5 size 96/08/23 Chapter 1 Pass 0, DR Selecting the paper size By default, the printer driver is set up for A4 size paper to be loaded. If you load paper of a different size, you need to change the paper size setting using one of the following methods. Using the printer driver: Choose the paper size on the Printer Settings menu or the Paper menu. For more information on using the printer driver, see online help in the driver.
L Albatross Rev.c A5 size 96/08/23 Chapter 1 Pass 0, DR Loading an uncommon paper size To load an uncommon, or custom, paper size from 92 × 140 mm (3.6 × 5.5 inches) to 330.2 × 483 mm (13 × 19 inches), use the MP Tray (as described in your Getting Ready guide) and make the size setting according to one of the following methods: ❑ Access the printer driver, click inside the paper size box on the paper menu, and type an original name for your paper.
Albatross Rev.c A5 size 96/08/23 Chapter 1 Pass 0, DR For best results, store your paper supply in its original wrapper. Your printout can be marred by moisture absorbed in the paper. Do not store paper in a humid or damp environment. Below are some recommendations for selecting paper and other print media for the printer. Labels Use only labels designed for laser printers or plain-paper copiers. Use the MP Tray to print on these materials.
L Albatross Rev.c A5 size 96/08/23 Chapter 1 Pass 0, DR Colored paper You can use colored paper as long as it meets the weight limits shown in the paper specifications. Do not, however, use coated paper (paper to which a clear or colored coating has been added). Transparencies You can use overhead projector transparencies and adhesive drafting film if they are made for use with plain-paper copiers or laser printers. Use the MP Tray to print on these materials.
Proof Sign-off: Nishi Grady Albatross Rev.c _______ _______ A5 size ’96/08/23 R Chapter 2 pass 0 Chapter 2 Understanding Your Printer The Control Panel . Overview . . . . Display . . . . . Indicator lights . Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L Albatross Rev.c A5 size ’96/08/23 Chapter 2 pass 0 This chapter shows you how to use the control panel. Getting acquainted with your printer’s control panel may help you get more from your printer. For more information on the SelecType settings available from the control panel, including the OneTouch modes, see Chapter 5. Appendix E shows all SelecType menu categories and options. It can be used as a guide whenever you use SelecType.
Albatross Rev.c A5 size ’96/08/23 R Chapter 2 pass 0 Display The display shows the following: ❑ Status messages, such as Warming Up , indicate the printer’s current status. ❑ Error messages, such as Paper Out , identify maintenance procedures you must perform or error conditions you need to correct. ❑ SelecType options, such as Emulation , allow you to control printer mode, font selection, paper handling, and several other printer functions.
L Albatross Rev.c A5 size ’96/08/23 Chapter 2 pass 0 Indicator lights On Line On when the printer is on line, indicating the printer can receive and print data. When the printer is off line, this light is off. The light flashes as the system switches between on-line and off-line status. Form Feed On when data is received and stored in the printer’s buffer but not yet printed. Flashing indicates the printer is processing data.
Albatross Rev.c A5 size ’96/08/23 R Chapter 2 pass 0 Buttons Paper Source Page Size Manual Feed Orientation RITech Copies MP Tray Size Toner Save Mode Menu Item Value Enter Item Menu Continue (Reset) SelecType Value Enter (Status Sheet) Form Feed Status Sheet On Line SelecType Alt Continue Form Feed On Line Reset On Line Switches the printer between on line and off line status. SelecType (ALT) Selects a OneTouch mode or SelecType mode.
L Albatross Rev.c A5 size ’96/08/23 2-6 Chapter 2 pass 0 Menu Selects the corresponding OneTouch mode setting listed above this button, or selects the SelecType menu if in SelecType mode. Press this button when the printer is on line to enter SelecType mode. Item Selects the corresponding OneTouch mode setting listed above this button or selects the function available within the current menu after entering the SelecType mode.
Proof Sign-off: Nishi Grady _______ _______ Albatross Rev.c R Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Chapter 3 Options Printer Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Installing an Optional Paper Tray . . . . . . . . . . . . . . . . . 3-3 Installing the Optional Lower Paper Cassette . . . . . . . . . . 3-7 Installing the Duplex Unit . . . . . . . . . . . . . . . . . . . . . 3-8 Removing the Duplex Unit . . . . . . . . . . . . . . . . . . 3-12 PCMCIA Card . .
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Printer Options You can add to your printer’s capabilities by installing any of the following options: ❑ 250 Sheet Paper Tray (C81270✽) increases paper feeding capacity for many sizes of paper up to A3 size paper. The supported paper sizes are shown below. A3, B4, F4, A4, B5, A5, Ledger, Legal, GLG, Letter, GLT, Exective, HLT Note: The asterisk (✽) is a substitute for the last digit of the product number, which varies by country.
Albatross Rev.c R Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 ❑ Optional interface cards and modules provide a link that enables you to use the EPL-N2000 with a LocalTalk network, IBM mainframe, and so on. With the optional interfaces, you can connect up to five different interfaces to this printer. See page 3-21. If you purchased your printer and options at the same time, first set up the printer and run the print test by following the instructions in the Getting Ready! guide.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 2. Open the cover of the paper tray. n1-5 3. Press down the plate in the paper tray until it locks into position. n1-6 4. Slide the paper guide out.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 R 5. Fan a stack of paper and tap it on a flat surface to even the edges. Insert the paper printable side up into the tray. 35-p68, 36-p68 Note: The direction you should load the paper depends on the paper size; see the table below. Paper size Side towards back of printer A4, B5, A5, Letter, GLT, HLT Long side of paper A3, B4, F4, Ledger, Legal, GLG, Exective Short side of paper 6.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 7. Close the cover of the paper tray and replace the paper tray in the paper cassette. r3-1 8. Adjust the extension output tray to match the size of your paper.
Albatross Rev.c R Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Installing the Optional Lower Paper Cassette The optional lower paper cassette gives you a third paper source, in addition to the MP Tray and standard lower paper cassette. This section describes how to install the cassette and load paper. 1. Turn off the printer. 2. Unplug the printer’s power cord from the electrical outlet and from the printer. 3. Remove all interface cables from the interface connectors. 4. Lift the printer.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 5. Reconnect any interface cables you removed. 6. Make sure the power is turned off and then plug the power cord into the printer and into an electrical outlet. 7. Turn on the printer. To confirm that the lower paper cassette is installed correctly, print a status sheet. If the cassette is not listed on the status sheet, try reinstalling it. Be sure to select the paper source in your application program.
Albatross Rev.c R Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 4. Facing the back of the printer, remove the screw and the cover as shown below. Note: Keep the screw and the cover in case you need to remove the Duplex Unit or need to transport the printer. r3-4 5. Attach the hooks that came with the Duplex Unit to the printer.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 6. Align the hooks on the printer with the holes at the bottom of the Duplex Unit. tori-aa 7. Attach the Duplex Unit to the printer, making sure the connectors and screws enter the proper holes. c Caution: Do not take off your hand until secure the Duplex Unit with the screws that came with the unit. Because the Duplex Unit may come off the printer, and damaged.
Albatross Rev.c R Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 8. Secure the Duplex Unit with two screws that came with the unit. c Caution: Be sure to secure the screws all the way; otherwise the printer may be damaged. r3-5 9. Reconnect any interface cables you removed. 10. Make sure the power is turned off and then plug the power cord into the printer and into an electrical outlet. 11. Turn on the printer. To confirm that the Duplex Unit is installed correctly, print a status sheet.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Removing the Duplex Unit 1. Perform steps 1 to 3 in “Installing the Duplex Unit,” page 3-8. 2. Facing the back of the printer, remove the two screws that secure the Duplex Unit to the printer. c Caution: Be sure you or someone else supports the Duplex Unit during removal; otherwise, the Duplex Unit may come off the printer and be damaged. r3-6 3. Pull the Duplex Unit, then lift it up gently.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 4. Remove the two hooks from the printer. Note: Save the hooks, in case you need to install the unit again in the future. 5. Secure the screw and the cover that you removed earlier when installing the Duplex Unit in step 4 on page 3-9. 6. Follow steps 9 through 11 in the previous section to complete the procedure. PCMCIA Card Install a PCMCIA card to increase printer memory.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Installing a PCMCIA card 1. Turn off the printer. 2. Open the IC card slot cover. r3-a 3. Insert the PCMCIA card as shown. Be sure the back side of the card is facing the inside of the printer. r3-b back side 4. Close the slot cover. 5. Turn on the printer.
Albatross Rev.c R Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Removing a PCMCIA card 1. Turn off the printer. 2. Open the IC card slot cover. 3. Press the Eject button to eject the card. r3-c 4. Close the slot cover. 5. Turn on the printer.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Memory Modules By installing a Single In-line Memory Module (SIMM) in both open slots, you can increase printer memory up to 68 MB. You may want to add additional memory if you are having difficulty printing complex, graphics-intensive pages or if you regularly use numerous downloaded fonts. You can purchase SIMMs from various vendors.
Albatross Rev.c R Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 4. Pull the latch on the right toward you to open the printer cover. g-1 5. Facing the left side of the printer, loosen the three screws that secure the side cover.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 6. Remove the printer’s side cover. r3-9 7. Insert the SIMM module into RAM SLOT 1 (if occupied use RAM SLOT 2), making sure the pin numbers of the slot and the SIMM match, either 1 or 72.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 R 8. Press the module in firmly until it clicks into place. Do not apply too much force. r3-11 9. Replace the printer’s side cover and secure the three screws that you loosened earlier.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 10. Gently press down on the printer cover until it clicks shut. r3-14 Removing a memory module 1. Perform steps 1 through 6 in the previous section to access the printer’s SIMM socket. 2. Pull the metal clips on each side of the SIMM socket outward to release the memory module.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 3. Grasp both sides of the SIMM and pull it out as shown above. 4. Follow steps 9 through 10 in the previous section to complete the procedure. ROM Module You can install the EPSONScript Level 2 module (C83226✽) using the same basic steps as those used to install the memory module. See “Installing a memory module” for installation instructions. However, this must be installed in the ROM SLOT rather than in the RAM SLOT.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 The coax and twinax connectors each contain a parallel interface. Since the printer’s built-in parallel interface remains active, this gives you three parallel interfaces and a coax or twinax interface. Print jobs can be sent to any connection, and the printer automatically switches between the active ports.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 R Installing the LocalTalk/Serial module Note: When using the module in LocalTalk mode, you should remove the Ethernet interface connector. For instructions on how to remove the connector, see “Installing a Type-B interface card,” steps 1 to 4, on the next page. 1. Perform steps 1 to 6 in “Installing a memory module,” page 3-16, to access the printer’s SIMM SLOT. 2.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 3. Position the module as shown below; then carefully insert its connector into printer connector CN4. Secure the module with the two screws that come with it. r3-15 4. Perform steps 9 to 10 on page 3-19 to complete this procedure. You can verify whether the interface is correctly installed by printing a status sheet. Installing a Type-B Interface Card 1. Turn off the printer.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 R 4. Loosen the two screws that secure the Ethernet interface connector card and remove the card. cor-3 5. With the component side of the Type-B interface card facing the outside of the printer, slide the interface card into the grooves in the interface slot as shown below. Push it in firmly to lock the card into place.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 6. Secure the Type-B interface card with the two retaining screws. r3-18 You can verify the interface is correctly installed by printing a status sheet. Using the Serial Interface To use a serial interface, you must purchase an appropriate interface cable. EPSON supplies several types of interface cables. You can use any interface cable that meets the printer specifications listed below.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 ❑ Current Loop Cable C836141 (0.4 m) from mini DIN (printer) to D-SUB 25-pin (interface cable) for both RS-232C and Current loop; a cable extension for printer to interface cable connection If you installed a serial interface, you need to ensure that the printer and the computer are using the same serial settings. If the serial settings do not match, you must make the appropriate settings.
L Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 For Windows 3.1 and Windows 3.11 for Workgroups 1. In the Main window, double-click the Control Panel icon. 2. Double-click the Printers icon. 3. In the Printers dialog box that appears, click the Connect button. 4. Select a COM (serial) port. 5. Click the OK button to save this setting. For Windows 95 1. Click the Start button, point to Settings, and then click Printers. 2.
Albatross Rev.c Reference Guide A5 size Chapter 3 ’96/08/23 DR, pass 0 Your printer supports the following serial interface baud rates: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, and 57600. If you want to use your printer with a higher baud rate that is supported by your computer system, you can use the utility to match the baud rate between the computer and printer. Note: This utility may not work with all computer systems. 1.
L Albatross Rev.
Proof Sign-off: Nishi Grady _______ _______ Albatross Rev.c A5 size ’96/08/23 R Chapter 4 DR, pass 0 Chapter 4 Remote Control Panel Utility Remote Control Panel Utility Overview . . . . . . When to use the Remote Control Panel utility . Installing the Remote Control Panel utility . . Accessing the Remote Control Panel . . . . . . LaserJet 4/EPSONScript Level 2 Mode . . . . . ESCP2 Mode . . . . . . . . . . . . . . . . . . . . FX Mode . . . . . . . . . . . . . . . . . . . . . . I239X Mode . . . . . . .
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Remote Control Panel Utility Overview The Remote Control Panel utility is software that allows you to change printer settings, such as the print quantity, paper size, and RITech setting. When to use the Remote Control Panel utility You do not normally need to use the Remote Control Panel to change printer settings.
Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 R Installing the Remote Control Panel utility To install the utility, follow these steps: 1. Insert the floppy disk containing the utility into your computer’s disk drive. 2. Type SETUP at the DOS prompt and press Enter. A:\SETUP 3. Follow the instructions on the screen to install the utility. Accessing the Remote Control Panel To start the Remote Control Panel, type the following at the DOS prompt and press Enter.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Click the button for the emulation mode you want to configure. Note: EpsonScript Level 2 is available only when the EpsonScript Level 2 option is installed. LaserJet 4/EPSONScript Level 2 Mode rcp1 The main menu displays the current printer settings for the selected printer mode. The buttons on the left open dialog boxes so you can change the settings listed under Printer Status.
Albatross Rev.
L Albatross Rev.
Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 If you are unable to make the settings that are available on the Page Setup menu from your software program, make the settings on this menu as follows: Page Size Selects the default paper size. You should change this item only if you cannot change the paper size from your software program. If your paper size is not listed below, you can define a new size using the Custom setting. Use the following settings when defining a custom page size: 92 to 330.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Copies Selects the number of copies to be printed. You can enter any number from 1 to 999. You should specify the number of copies from your software program. Form Specifies the number of horizontal lines on a page. You can enter any number from 5 to 128. This setting is available only in LJ4 mode. Orientation Specifies whether the page is printed in portrait (default) or landscape orientation.
Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 R Type Options Clicking the Type button on the Remote Control Panel menu opens the following menu. Note: The Type menu is available only in LJ4 mode. no8aa If you are unable to make the settings that are availabe on the Type menu from your software program, make the settings on this menu as follows: Typeface Specifies the typeface to use. Pitch / Point Size Specifies the point size for proportional and scalable fonts. The range of point sizes is 4.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Symbol Set Specifies the symbol set to use. If the typeface you selected is not available for the symbol set you select, the typeface is replaced with the currently selected symbol set. The following symbol sets are available: Roman-8 Italian Swedis2 UK German 8859-2 ISO PsMath WiTurkish VeMath Math-8 PcTk437 PsText IBM-DN PcMultilingual VeUS PcE.Europe WiAnsi Norweg1 ECM94-1 ANSI ASCII French2 Legal Spanish 8859-9 ISO MsPublishing DeskTop WiE.
Albatross Rev.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Page Protect Use this list to make use of the Page Protect function. This allows you to allocate additional printer memory for printing data, as opposed to receiving it. You may need to use Page Protect if you are printing a highly complex page. If a Print Overrun error occurs, change the setting to ON and reprint your data.
Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Auto Continue Permits the printer to automatically recover from a Print Overrun, Mem Overflow, or Paper Set error. The printer continues printing within a few seconds after one of these problems occurs. When Auto Continue is off, you must press the button on the control panel to resume printing. In most cases, leave Auto Continue off so you can tell when an error occurs and make the necessary corrections.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Other Options Clicking the Other button brings up the following dialog box. This menu is available only in ESC/P 2, FX, or I239X emulation modes. no10aa Condensed (ESCP2, FX only) Use this option to change the character spacing. Condensed printing is useful for spreadsheets and other applications that need to fit a large amount of information on each line. However, 15-cpi characters cannot be condensed. T.
Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Text Use this option to set the page length in lines. The unit of measure for this option is a 1/6 inch line. If you change the Orientation, Page Size, or T.Margin settings, the page length setting automatically returns to the default setting for each paper size. AutoCR Use the automatic carriage return option to perform a carriage-return line-feed (CR-LF) operation whenever the print position exceeds the right margin.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 ZeroChar This option determines whether the printer prints a slashed zero (0) or an unslashed zero (0). This feature is useful for clearly distinguishing between an uppercase letter O and zero when printing documents such as program lists. Alt.Graphics (I239X only) Turns the Alternate Graphics option on or off. The default setting is OFF. Character Set (I239X only) Selects the character table 1 or 2. Next (I239X only) Turn to the next page.
Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 R More Options Clicking the More button on the Remote Control Panel menu opens the following menu: no11aa If you are unable to make the settings available on the More menu from your software program, make the settings on this menu as follows: Source Symbol Set (LJ4 only) Available only when an optional font ROM is installed while in the LJ4 emulation mode.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Top Offset Allows you to adjust the vertical printing position on the page. The setting is in millimeters. You can move the printing position by approximately 0.5 mm increments from the top edge (the parameters are from -9 to 99). Left Offset Allows you to adjust the horizontal printing position on the page. The setting is in millimeters. You can move the printing position by approximately 0.
Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 R Country (ESCP2, FX only) Selects the international character set. CG Table (ESCP2, FX only) Selects the character tables. Character tables contain the characters and symbols used in different languages. The printer prints text based on the selected character table. Code Page (I239X only) Selects the character tables. Character tables contain the characters and symbols used in different languages.
L Albatross Rev.c A5 size ’96/08/23 Chapter 4 DR, pass 0 Duplex Selects the duplex printing on or off. This item is available only when the Duplex Unit is installed. Binding Selects the binding direction of the printout. This item is available only when the Duplex Unit is installed. Start Page Specifies to print from either front or back at first. This item is available only when the Duplex Unit is installed. Back Shift Adjusts the printing position on the back side when printing on both sides.
Proof Sign-off: Nishi Norum Grady Albatross Rev. c _______ _______ _______ A5 size 96/08/23 R Chapter 5 Pass 0, DR Chapter 5 SelecType 5 When to Use SelecType . . . . . . . . . . . . . . . . . . . . . . . 5-2 SelecType . . . . . . . Buttons . . . . . . Using SelecType . SelecType menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L Albatross Rev.
Albatross Rev. c A5 size 96/08/23 R Chapter 5 Pass 0, DR SelecType Before entering and using SelecType, you should understand how the buttons on the printer’s control panel work. Buttons The functions of the control panel buttons on the printer change when in SelecType mode.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR 2. To change the settings, press Menu, Item, or Value. ❑ To select a new menu (menu category), press Menu. ❑ To select an item (setting) in a menu, press Item. ❑ To select a value (parameter) for an item, press Value. ❑ To accept a new setting, press Enter. ❑ Press ALT to select a menu, item, or parameter in reverse order. See Appendix E for a map showing the order that selecType menus are displayed in. 3.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Emulation Menu These settings select the default emulation for each interface. Also see page 5-9. Parallel B, Parallel C, Serial*, L/T*, AUX** * available only when the LocalTalk/Serial module is installed **available only when the optional interface is installed. Printing Menu These settings are made in everyday use. Most can be set using your software.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Setup Menu These settings provide the printer with information necessary for printing. Also see page 5-15. Interface, Time Out, Standby, Lang, Printer Name, Toner, Page Count, SelecType Init Parallel B, Parallel C Menu These settings control communication between the printer and the computer when using a parallel interface. Also see page 5-16. Speed, Bi-D, Buffer Size Serial Menu* These settings control the serial interface settings.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR LJ4 Menu These settings control the fonts and symbol sets when in LJ4 mode. Also see page 5-19. FontSource, Font Number, Pitch, Height, SymSet, Form, Source SymSet, Dest SymSet GL2 Menu These settings are available only when the printer is in GL2 mode. Also see page 5-28. PS Menu These settings are available only when EPSONScript Level 2 is installed. For more information, refer to the EPSONScript Level 2 manual.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Understanding SelecType Settings Read this section for a complete description of the settings available on the SelecType menus. Test Menu For the settings below, press Enter to print. No values are selectable by pressing Value. c Caution: After you print these samples, user-defined data stored in the printer such as download fonts may be erased depending on which sample you printed.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Emulation Menu Use this menu to select the printer emulation mode. You can specify different emulations for each interface; in other words, for each computer you connect. Since each emulation mode has its own specific options, make settings in the LJ4, ESCP2, FX, GL2, or I239X menus, as necessary. The options you can set are the same for every interface.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Page Size Specifies the paper size. Orientation Specifies whether the page is printed in portrait or landscape orientation. This page is printed in portrait orientation. Copies Selects the number of copies to be printed, up to 999. Manual Feed Selects manual feed mode for the MP Tray. For details on manual feed mode, see Chapter 1. Resolution Switches the resolution between 300 and 600 dpi. Duplex Selects the duplex printing on or off.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Start Page Specifies to print from either front or back at first. This item is available only when the Duplex Unit is installed.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR LC1 Size Displays the actual paper size loaded in the standard lower paper cassette. Note: LC1 Size and LC2 Size only display the currently loaded paper size. You cannot change this parameter, it is set automatically. LC2 Size Displays the actual paper size loaded in the optional lower paper cassette.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Toner Save Turns the Toner Save mode on. When turned on, the printer saves toner by substituting a gray shade for the black inside of characters. The characters are outlined in full black on the right and lower edges. Note: You can also make the Toner Save setting item directly from OneTouch Mode 2. Density Adjusts the print density to make your printout lighter or darker. Note: Increasing the print density increases toner consumption.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Back Shift Adjusts the printing position on the back side when printing on both sides. Use this if the printout on the back side is not where you expected. This item is available only when the Duplex Unit is installed. Size Ignore Selects whether a paper size error is ignored. Turning this item on causes the printer to print even if the image size exceeds the printable area for the specified size of paper.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Image Optimum Reduces the amount of graphics data when the data reaches the memory limit, allowing complex documents to be printed. When this mode is on, graphics quality is reduced. Paper Type Allows you to use various types of paper. Thin is useful for the regular size plain paper under 75g/m2. Thick is useful for irregular size plain paper over 75g/m2 and envelopes that are less than 257mm wide. Trnsprnc is useful for transparencies.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Printer Name Displays the printer name instead of Ready when the printer is standing by. Toner Displays the amount of toner left in the imaging cartridge. E****F E*** F E** F E* F E F (100-75%) (75-50%) (50-25%) (25-0%) (0%) Page Count Displays the total number of sheets printed by this printer. SelecType Init. Erases all the SelecType settings you have changed, and resets them to the factory default settings.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Buffer Size Determines the amout of memory to be used for receiving data and printing data. If set to Maximum, more memory is allocated for receiving data. If set to Minimum, more memory is allocated for printing data. The factory default setting is Normal. Serial Menu Word Length You can select an 8-bit or 7-bit word length. See your computer manual and software documentation for the proper setting. The factory setting is 8-bit.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR XOn/XOff Use this option to set XOn/XOff communications protocol to On, Off, or Robust. You can use XOn/XOff protocol in combination with the DTR option setting. If set to Robust, the printer sends an XOn signal every second the printer is waiting to receive data. DTR Use DTR (Data Terminal Ready) to turn the printer’s DTR communications protocol on or off. You can use DTR protocol in combination with the XOn/XOff option setting.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR LJ4 Menu Note: If you always use the HP LaseJet 4 printer driver in your software, you should change settings using your software. The software settings always override the LJ4 menu options. FontSource Selects the default font source. Font Number Selects the default font number from the default font source. Pitch Specifies the default font pitch if the font is scalable and fixed-pitch. You can select from 0.44 to 99.99 CPI, in increments of 0.01 CPI.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Source SymSet Available only when an optional font ROM is installed. Dest SymSet Available only when an optional font ROM is installed. Setting Parameter FontSource Resident, SIMM, Card, Download Font Number 0 ~ 65535 Pitch 0.44 ~ 99.99 cpi Height 4.00 ~ 999.75 pt. SymSet Roman-8, ECM94-1, 8859-2 ISO, 8859-9 ISO, IBM-US, IBM-DN, PcMultiling, PcE.Europe, PcTk437, WiAnsi, WiE.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR R Using the OneTouch Modes The OneTouch modes are part of SelecType mode, but they are more limited and easier to use. The settings you make in these modes and SelecType are reflected in each other. To enter OneTouch mode 1, press the SelecType button (repeatedly if necessary) until the light next to Paper Source comes on indicating the printer is now in OneTouch mode 1.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Paper Source Specifies whether paper feeds into the printer from the MP Tray, the standard lower paper cassette, or from the optional lower paper cassette (if installed). If you select Auto , the paper source containing the paper that matches the setting in the Page Size menu will be used. Page Size Specifies the paper size. Manual Feed Turns Manual Feed on or off for the MP Tray. For details on the Manual Feed mode, see Chapter 2.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Using Other Emulation Modes Your printer is designed to work best in its LJ4 emulation mode. If you want to use an emulation other than LJ4, you can select ESC/P 2, FX, I239X, or GL/2 emulation mode. Match the emulation mode in the Emulation Menu with drivers or print data already formatted for EPSON LQ or FX series printers, or IBM printers. The available emulation modes are LJ4 (default), GL2, I239X, ESC/P 2, and FX.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR ESC/P 2 or FX Mode This section lists the ESCP2 menu and FX menu options. Unless specifically mentioned, the same items are available for either mode. Font The Font option selects a font by typeface. The factory default font is Courier. After selecting the desired font, you can also adjust the character spacing and size of the font with the Pitch and Condensed options described below.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR CG Table Use the character generator table option to select the graphics character table, or the italics table. The graphics table contains graphic characters for printing lines, corners, shaded areas, international characters, Greek characters, and mathematical symbols. Selecting the italics table defines the upper half of the character table as italic characters. Country Use this option to select one of the fifteen international symbol sets.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR The BarCode setting converts bit images to bar codes by automatically filling in any vertical gaps between dots. This produces unbroken vertical lines that can be read by a bar code reader. BarCode is not available in I239X mode. This mode reduces the size of the image being printed and may cause some distortion when printing bit-image graphics. ZeroChar This option determines whether the printer prints a slashed zero (0) or an unslashed zero (0).
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR I239X Mode I239X mode emulates IBM 2390/2391 Plus commands. For detailed information on most of the settings and parameters in the table below, refer to the previous section. Setting Parameter Font Courier, Prestige, Gothic, Orator, Script, Presentor, Sans serif Pitch 10 cpi, 12 cpi, 15 cpi, 17 cpi, 20 cpi, 24 cpi, Prop. Code Page 437, 850, 860, 863, 865 T. Margin 0.30 - 1.50 inch Text 1 - 81 Lines Auto CR Off, On Auto LF Off, On Alt.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR EPSON GL/2 Mode Note: You cannot change the GL/2 Mode items by SelecType. To change these items, use the GL/2 command listed in Appendix C. In EPSON GL/2 mode, you can use your printer with plotter applications. EPSON GL/2 has two operational modes. One is the LJ4GL2 mode; the other is the GLlike mode. The GLlike mode emulates some of the HP-GL plotter commands and includes all of the commands found in LJ4GL2 mode, plus two additional commands.
Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR Before printing in EPSON GL/2 mode You may need to change printer settings depending on your output needs. First, check the print settings to make sure they match the data you are trying to print. Check the following items; the information may be necessary later.
L Albatross Rev. c A5 size 96/08/23 Chapter 5 Pass 0, DR GL2 Menu GL Mode Selects the mode, GLlike or LJ4GL2. Scale Switches between original size or reduced size printing. Also, determines the reduction scale for reduced printing. You can print the data originally created for the paper size selected in the Scale setting onto the paper selected in the Page Size setting. For example, you can scale an A3 size page to an A4 size page.
Albatross Rev. c A5 size 96/08/23 R Chapter 5 Pass 0, DR End Determines the type of line ending. See the illustration below. Butt Square Triangular Round end Join Defines how the ends of lines are joined. See the illustration below. NONE MITERED MITEREDBEVELED ROUND BEVELED TRIANGULAR Pen 0, Pen 1, Pen 2, Pen 3, Pen 4, Pen 5, Pen 6 Selects the line width. You can select a value from 0.05mm to 5.00mm, in increments of 0.05 mm.
L Albatross Rev.
Proof Sign-off: Nishi Norum Grady Albatross Rev.c _______ _______ _______ A5 size 96/08/23 R Chapter 6 Pass 0, DR Chapter 6 Troubleshooting and Maintenance Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Paper Jam and Feeding Problems . . . . . . . . . . . . . . . . . 6-2 Preventing paper feed and paper jam problems . . . . . . . 6-5 Print Quality Problems . . . . . . . . . . . . . . . . . . . . . . . 6-9 Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . . .
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Introduction This chapter provides the information necessary for you to keep the printer in optimum condition. This chapter tells you how to ❑ Solve problems you may encounter ❑ Replace consumables ❑ Optimize print quality Also included is a complete description of the status, error, and warning messages shown on the printer’s control panel display. Paper Jam and Feeding Problems The printer stops and the Feed Jam message appears. 1.
Albatross Rev.c A5 size 96/08/23 R Chapter 6 Pass 0, DR 2. Open the printer cover. Be sure to remove any pieces of paper that may have torn off or are remaining in the printer. w Warning: Opening the printer cover exposes the fuser, which is marked by a CAUTION Hot Surface Avoid Contact label. Be careful not to touch the fuser. If necessary, remove the Imaging Cartridge and any paper left in the paper feed path, and then reinsert the Imaging Cartridge. 3. Close the printer cover.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR 3. Tap the edge of the paper stack. Then reinsert it into the paper tray making sure the paper is evenly aligned and rests below the maximum paper mark. Make sure you are using the correct paper size. Also make sure you are using paper that meets the specifications for this printer. 4. Reinstall the paper tray in the lower paper cassette. 5. Press the Continue button. The jammed page’s print data is automatically reprinted.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Note: Because the toner on the paper inside the printer may not have been fixed on the page, toner may come off on your hands when you remove the paper. If you spill toner on your clothing, rinse it off with cold water. Using hot water may leave a permanent stain. 3. Reinstall the Imaging Cartridge. Then close the printer cover. 4. After a paper jam, the jammed page’s print data is automatically reprinted.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR The display panel stays blank when you turn the printer on. Turn off the printer and check the power cable connections between the printer and the electrical outlet; then turn the printer back on. If the electrical outlet is controlled by an outside source such as a wall switch, make sure the switch is turned on or plug another electrical device into the outlet to check whether the outlet is operating properly.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR The printer doesn’t print and the On Line light is off. Press On Line once to put the printer on line (the On Line light comes on). A font selected with software commands won’t print. The selected font is not installed in your printer. Be sure you have installed the correct font. See Appendix D for more information. Some or all of the output is garbled.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR The position of the printout is not correct. Make sure that you are using the correct page length and margin settings in your application program. Graphics don’t print correctly. Make sure that your software program is set for the printer emulation you are using. For example, if you are using the LJ4 emulation, be sure that your graphics software is set for a LaserJet 4 printer.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR You may not have reset the printer after making settings. Press the ALT button and Continue button at the same time to reset the printer and enable the new settings. When transporting the printer c Caution: Whenever you ship or transport the printer, first remove the Imaging Cartridge and place it in a plastic bag. Seal the bag to prevent the fine toner particles from spilling into the printer or onto your clothing.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Vertical black or white bands or lines Clean the printer lens. Remove the Imaging Cartridge and place it on a clean, flat surface. Clean the lens as shown below. r6-4 Wipe the lens from end to end with a dry, lint-free cloth. Then reinsert the imaging cartridge in the printer and close the printer cover. If the problem persists, install a new imaging cartridge as described later in this chapter and print several pages to check the print quality.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Horizontal black or white bands appear in your printout, or the printer prints a blank page Install a new Imaging Cartridge as described later in this chapter. Uneven darkness Take out the Imaging Cartridge, shake it from side to side, and reinstall it. Your paper may be moist or damp. Printing is sensitive to moisture absorbed by the paper. Do not store your paper in a humid or damp environment.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Missing areas on printed image Your paper may be moist or damp. Printing is sensitive to moisture absorbed by the paper. The higher the moisture content in the paper, the lighter the printed output. Do not store your paper in a humid or damp environment. You may not be using the correct type of paper for your printer. If the surface of your paper is too rough, printed characters appear distorted or broken.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Printed image is light or faint Darken the Density setting using the printer driver, Remote Control Panel utility, or the SelecType Config Menu. Your paper may be moist or damp. Printing is sensitive to moisture absorbed by the paper. The higher the moisture content in the paper, the lighter the printed output. Do not store your paper in a humid or damp environment.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Non-printed side of the page is dirty Toner may have spilled in the paper feed path. Remove the Imaging Cartridge and then clean the paper path of the printer using a soft, lint-free cloth. c Caution: Opening the printer exposes the fuser, which is marked by a CAUTION Hot Surface Avoid Contact label. Be careful not to touch the fuser.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Option Problems The message Illegal AUX I/F Card or Illegal I/F Module appears The message Illegal AUX I/F Card means that the printer cannot read the installed optional interface card. Turn off the printer, then remove the card. The message Illegal I/F Module means that the printer cannot read the installed optional LocalTalk/Serial module. Turn off the printer, then remove the module.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Feed Jam when using the optional lower paper cassette See “Feed Jam when using the lower paper cassette”, on page 6-3. Feed Jam when using the Duplex unit 1. Press the top of the Duplex unit and open the cover. r6-5 2. Remove any folded paper from the unit, and discard any curled or wrinkled sheets. Then close the cover. If you cannot remove the paper, follow the step 3 and 4.
Albatross Rev.c A5 size 96/08/23 R Chapter 6 Pass 0, DR 3. Pull open the lower cover. n6-7 4. Remove any folded paper from the unit, and discard any curled or wrinkled sheets. Then close the cover. r6-8 5. The jammed page’s print data is automatically reprinted.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Even with additional memory installed, complex pages don’t print and the Mem Overflow message still appears. The Page Protect setting in the printer driver, the Remote Control Panel utility, or SelecType may need to be changed. See “Memory Problems” in this chapter for more information. You may not have installed enough memory. If you are printing at 600 dpi, printing at 300 dpi may solve the problem.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR If you turn on Size Ignore in the SelecType Config menu, this error does not occur. Check Paper Size The paper size setting is different from the size loaded in the printer. Check to see if the correct size of paper is loaded in the tray; then press the Continue button to clear the message. If you turn on Size Ignore in the SelecType Config menu, this error does not occur. Check Serial I/F This error occurs in serial interfaces.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Duplex print was off Turn Duplex mode on in the SelecType menu, then press Continue to clear the message. If this doesn’t solve the problem, one of the conditions below has occured and needs to be fixed. 1) Paper Size is incorrectly set to CTM, MON, C10, DL, C5, or C6; set this option to a supported paper size. 2) Paper Type is set to something other than Normal; set this to Normal. 3) The Duplex Unit is not installed; install the Duplex Unit.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Form Feed When the printer is off line and data remains in the printer’s memory, pressing Form Feed prints out the data and clears the buffer. After printing, Ready appears on the display. Illegal AUX I/F Card The printer cannot read the installed optional interface card. Turn off the printer, then remove the card. Both the LocalTalk/Serial module (set in LocalTalk) and the LocalTalk Type B interface card are installed simultaneously.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Image Optimum The printer cannot print at the requested quality level because of insufficient memory, and the printer reduces the quality automatically so that the printer can continue printing. Check to see if the printout is acceptable. If not, add more memory (for a permanent solution) or set Device Resolution to Low (300 dpi) and Page Protect to Auto temporarily in the driver.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Operate Error Card The PCMCIA card is installed or removed while the printer is on. To correct the error, (1) reset the printer by pressing ALT and Reset at the same time or (2) turn off the printer; then turn it back on. Paper Jam Paper is jammed in the paper path. Open the printer cover and clear the jammed paper as described in the PAPER JAM section in this chapter. After the jam is cleared, the jammed page’s print data is automatically reprinted.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Paper Set XXX YY The paper loaded in the tray (XXX) does not match the required paper size, (YY). Replace the paper with the correct size of paper and press Continue. Print Overrun The time required to process data exceeds the print engine speed because the volume of data is too great. Press Continue to resume printing. If this message appears again, change the Page Protect setting in SelecType Config Menu. Printer Open The printer cover is open.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Reset All All printer settings have been reset to the user default configuration, the last settings that were saved. Reset to Save You have changed the SelecType setting but the new setting is not activated immediately after exiting SelecType.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Service Req.CXXX Service Req.EXXX A controller error or a print engine error has been detected. Write down the error number listed on the display and turn off the printer. Wait at least five seconds and then turn it back on. If the error message still appears, turn off the printer, unplug the power cord, and contact a qualified service person. Standby The printer is in its low power state; however, it is still on line if the On Line light is on.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Write Error Card The card is not able to write or the card is not installed. Otherwise, writing to the card was not finished correctly. To correct this error, (1) turn off the printer and remove the card, then turn on the printer, (2) remove the card while the printer is on, then press the Continue button, or (3) reset the printer by pressing the ALT and Reset button at the same time. Writing Card The printer is writing data in the PCMCIA card.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Hex Dump Mode Hex Dump Mode (also called data dump) is a special feature that makes it easy for experienced users to find the cause of communication problems between the printer and the computer. In Hex Dump Mode the printer produces an exact printout of the codes it receives. 1. Make sure the paper is loaded and the printer is off. 2. Hold down the Form Feed button while you turn on the printer.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Replacing the Imaging Cartridge The Imaging Cartridge prints up to 10,000 pages depending upon the complexity of your print jobs. If your printed images become faint, enter the SelecType Setup menu to use the Toner function to find out approximately how much toner remains in the imaging cartridge. Simply count the asterisks between the E (empty) and the F (full) on the display. Each asterisk represents about 25% of the total toner capacity.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR 4. While holding the cartridge horizontally, gently shake it a few times to distribute the toner evenly. s-8 5. Set the Imaging Cartridge on a clean, flat surface. Firmly grip the tab on the right side of the Imaging Cartridge. Pull the clear seal all the way out with firm, even pressure as shown.
Albatross Rev.c A5 size 96/08/23 R Chapter 6 Pass 0, DR 6. Insert the pins on each side of the Imaging Cartridge into the grooves inside the printer, and slide the cartridge gently into place. Then push down the handle until the Imaging Cartridge is horizontal. r6-9 7. Gently press down on the printer cover until it clicks shut. r6-10 c Caution: Never transport the printer with the Imaging Cartridge installed.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Optimizing Print Quality Adjusting RITech Resolution Improvement Technology (RITech) is EPSON’s new printer technology that improves the appearance of printed lines, text, and graphics. The RITech setting The factory setting for RITech gives the best quality text and graphics for nearly all purposes. You may not need to set or adjust anything. Occasionally, however, adjusting the RITech setting may further improve the print quality.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR If the test pattern seems too heavy, change the setting to Light as described below; if it seems too light, change the setting to Dark; if you are printing gray shading or screen patterns, change the setting to Off. To change the RITech setting, follow these steps: Using the printer driver: Changing the RITech setting on the Printer SelecType menu in the printer driver.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Using the printer driver: Change the Density setting on the Printer SelecType menu in the printer driver. Using the Remote Control Panel utility: Bring up the Remote Control Panel utility by typing EPRCPO at the DOS prompt; select the appropriate emulation from the main Remote Control Panel window; click the Printer Setup button; then change the Density setting. Using the SelecType mode: For information on using SelecType, see Chapter 5.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR R Cleaning the Printer The printer needs only minimal cleaning. If you notice a decline in print quality, clean the glass lens and the inside of the printer, as described in this section. You should also clean the paper feeder and the printer cover every few months. These procedures are described later in this section. Follow the steps below to clean the inside of the printer and the paper feeder: 1. Make sure the printer is turned off. 2.
L Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR 5. Reinstall the Imaging Cartridge. 6. Close the printer cover. 7. Open the front cover and clean the paper feeder with a soft cloth. Removing spilled toner If toner spills inside the printer, do not use the printer until you remove all the spilled toner. Follow these steps: 1. If only a small amount of toner is present, carefully wipe out the inside of the printer with a dry cloth. 2.
Albatross Rev.c A5 size 96/08/23 Chapter 6 Pass 0, DR Cleaning the printer case If the printer’s outer case is dirty or dusty, turn off the printer and clean it with a soft, clean cloth dampened with a mild detergent. c Caution: Never use alcohol or thinner to clean the printer cover; these chemicals can damage the components and the case. Be careful not to get water on the printer mechanism or any electronic components.
L Albatross Rev.
Proof Sign-off: Nishi Norum Grady Albatross Rev.c _______ _______ _______ A5 size 96/08/23 R Appendix A pass 0 Appendix A Technical Specifications Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Printer . . . . . . . General . . . . Environmental Mechanical . . Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 Paper Specifications Note: Since the quality of any particular brand or type of paper may be changed by the manufacturer at any time, EPSON cannot guarantee the guality of any type of paper. Always test samples of paper stock before purchasing large quantities or printing large jobs.
Albatross Rev.c A5 size 96/08/23 Envelopes: c Appendix A pass 0 Monarch (3 7/8 × 7 1/2 inches) Commercial 10 (4 1/8 × 9 1/2 inches) DL (110 mm × 220 mm) C5 (162 mm × 229 mm) International B5 (176 mm × 250 mm) C6 (114 mm × 162 mm) Caution: Only load paper sizes that are listed above. Printable area: 4 mm minimum margin on all sides (A3+: 297 mm × 420 mm) Note: Printable area varies according to the emulation mode.
L Albatross Rev.
Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 Electrical 120 V model 230 V model Voltage 108 V to 132 V 207 V to 253 V Rated frequency 50 Hz to 60 Hz ± 3 Hz 50Hz to 60Hz ± 3Hz Rated current 7A 4A Power consumption Less than 750 W Less than 750 W Power consumption * in Standby mode Less than 45 W Less than 45 W * No option installed Note: Check the label on the back of the printer for the voltage of your printer.
L Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 Pin No.
Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 Parallel C interface The parallel C (IEEE 1284-II compliant) interface connector pin assignments and a description of the interface signals are shown in the table below. Pin No.
L Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 nStrobe/HostClk Compatibility mode: Latch pulse used to read in print data. When low, DATA is valid. negotiation phase: Latch pulse used to read in extensibility request values. Nibble mode: Always high. ECP mode: Used to transfer data and addresses from the host to the printer with handshaking via PeriphAck (Busy). DATA1 to DATA8 (bidirectional, but may always be an input if ECP or EPP mode is not supported) Compatibility mode: Forward channel data.
Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 Busy/PtrBusy/PeriphClk Compatibility mode: High signal indicates that the printer is not ready to receive data. negotiation phase: Reflects the BUSY status of the forward channel. reverse data transfer phase: In nibble mode, this signal serves as nibble data bit 3 and then 7. reverse idle phase: Reflects the BUSY status of the forward channel. ECP mode: Used for forward direction flow control.
L Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 nAutoFd/HostBusy/HostAck Compatibility mode: Not used. negotiation phase: In order to request 1284 mode, this signal is set low and IEEE 1284 Active (nSelectln) is set high. Afterwards, this signal is set high when PtrClk (nAck) is set low. reverse data transfer phase: In nibble mode, setting this signal low indicates to the printer that the host is ready to receive data.
Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 nFault/nDataAvail/nPeriphRequest Compatibility mode: Low signal indicates that an error occurred. negotiation phase: This signal is set high in order to authorize 1284 compatibility. In nibble mode, after the host sets HostBusy (nAutoFd) high, this signal is set low in order to indicate that the transmission data is ready. reverse data transfer phase: This signal is set low in order to indicate to a nibble mode host that the transmission data is ready.
L Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 Ethernet Interface You can use a IEEE 802.3 10BASE2 RG-58A/U coaxial cable via BNC connector or IEEE 802.3 10BASE-T straight-through twisted pair modular cable via RJ45 connector.
Albatross Rev.
L Albatross Rev.c A5 size 96/08/23 Appendix A pass 0 Imaging Cartridge (S051035) Storage temperature: 0 to 35°C (32 to 95°F) Storage humidity: 30 to 85% RH Shelf life: 18 months after production Life: Up to 10,000 pages under the following conditions: Letter or A4-size paper, continuous printing, and 5% print ratio The number of pages you can print with an imaging cartridge varies depending on the type of printing.
Proof Sign-off: Nishi Grady _______ _______ Albatross Rev.c A5 size 96/08/23 R Appendix B pass 0 Appendix B Symbol Sets Introduction to Symbol Sets . . . . . . . . . . . . . . . . . . . . . . B-2 In LJ4 Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . B-3 International Set for ISO sets . . . . . . . . . . . . . . . . . . . . B-18 In ESC/P 2 or FX Modes . . . . . . . . . . . . . . . . . . . . . . . . B-19 International Character Sets . . . . . . . . . . . . . . . . . . . .
L Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 Introduction to Symbol Sets Your printer can access a variety of symbol sets. Many of these symbol sets differ only in the international characters specific to each language. Note: Normally, your software handles fonts and symbols, so you probably never need to adjust the printer’s settings.
Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 In LJ4 Emulation Mode The following table lists the symbol sets available in LJ4 emulation mode. A table of the characters for each set is included later in this chapter. Symbol set name Roman-8* (includes another 19 sets) Roman Extension ECM94-1 Legal 8859-2 ISO PsMath 8859-9 ISO WiTurkish MsPublishing VeMath DeskTop Math-8 WiE.Europe PcTk437 Windows PsText IBM-US IBM-DN McText PcMultilingual VeInternational VeUS PiFont PcE.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 Math-8M Math-8 WiE.Europe (9E) WiE.
Albatross Rev.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 PcE.Europe (17U) Pce.
Albatross Rev.
L Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 International Set for ISO sets To obtain the symbol sets listed below, substitute the characters in the ANSI ASCII sets with the characters in the table below.
Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 R In ESC/P 2 or FX Modes PC 437, 850, 860, 863, 865 857, 852, BRASCII, Abicamp PC 437 EPSON Roman N × × Courier SWC N N × EPSON Sans serif N × × EPSON Prestige N × × EPSON Script N × × Letter Gothic SWC N N × Swiss 721 SWM N N × Dutch 801 SWM N N × OCR B × × N *Available only in ESC/P 2 mode. PC437 (U.S.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 Italic Italic No characters are available for hex code 15 in the italic character table.
Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 International Character Sets You can select one of the following international character sets using either SelecType or the ESC R command. For example, when you select “Italic France” in SelecType, the characters in the “France” row in the table below are used in the italic character table.
L Albatross Rev.c A5 size 96/08/23 Appendix B pass 0 Characters available with the ESC (^ command To print the characters in the table below, use the ESC (^ command. In I239X Emulation Mode Available symbol sets in I239X mode are PC437, PC850, PC860, PC863, and PC865. Refer to “ESC/P 2 or FX modes” in the previous section. Available fonts are EPSON Sans Serif, Courier SWC, EPSON Prestige, EPSON Gothic, EPSON Presentor, EPSON Orator, and EPSON Script.
Proof Sign-off: Nishi Grady Albatross Rev.c _______ _______ A5 size 96/08/23 R Appendix C pass 0 Appendix C Command Summary C LaserJet 4 (LJ4) Emulation Commands . . . . . . . . . . . . . . . . C-3 GL/2 context commands . . . . . . . . . . . . . . . . . . . . . . C-7 ESC/P 2 and FX Commands . . . . . . . . . . . . . . . . . . . . . . C-9 ESC/P 2 mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9 FX mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-12 PJL Commands .
L Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 Your printer has the ability to emulate the following printers depending on the printer emulation mode: LJ-4 Hewlett-Packard LaserJet 4 (PCL5e) ESC/P 2 EPSON LQ-570 (24-pin) FX EPSON FX-870/1170, or LX-100 (9-pin) GL/2 Hewlett-Packard GL/2 graphics language In addition, the following printer control languages are supported: PJL Printer Job Language EJL EPSON Job Control Language This appendix lists the printer commands for these modes.
Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 LaserJet 4 (LJ4) Emulation Commands This section lists the printer commands supported in the LJ4 emulation mode. For more information on printer commands, see HewlettPackard’s LaserJet 4 reference manual.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.
Albatross Rev.
L Albatross Rev.
Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 ESC/P 2 and FX Commands This section lists the printer commands supported in the ESC/P 2 and FX emulation modes.
L Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 Print position motion Set absolute horizontal print position Set relative horizontal print position Set absolute vertical print position Set relative vertical print position Set horizontal tabs Tab horizontally Set vertical tabs Tab vertically Advance paper n/180 inch Reverse paper n/180 inch ESC $ n1 n2 ESC \ n1 n2 ESC ( V nn ESC ( v nn ESC D nn HT ESC B nn VT ESC J n ESC j n Font selection Select typeface Select font by pitch and point Select 10.
Albatross Rev.
L Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 FX mode Printer commands arranged by topic The following section lists and describes all FX and LQ commands by topic.
Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 Horizontal motion Set absolute horizontal print position Set relative horizontal print position Set left margin Set right margin Tab horizontally Set horizontal tabs ESC $ n1 n2 ESC\n1 n2 ESC l n ESC Q n HT ESC D nn Overall printing style Select letter quality or draft ESC x n Note: The print quality and speed cannot be changed even if you send the ESC x command.
L Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 Font enhancement Select emphasized mode Cancel emphasized mode Select double-strike mode Cancel double-strike mode ESC E ESC F ESC G ESC H Note: The ESC G and ESC E commands produce identical effects, so you cannot obtain darker print by combining the two.
Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 PJL Commands This section lists the available commands for printer job language mode (PJL). For more information on PJL, refer to the Printer Job Language Technical Reference Manual from Hewlett-Packard.
L Albatross Rev.c A5 size 96/08/23 Appendix C pass 0 I239X Emulation Commands This section lists the printer commands supported in the I239X emulation mode. For more information on these commands, see IBM’s 2390/2391 reference manual.
Albatross Rev.
L Albatross Rev.
Albatross Rev.
Proof Sign-off: Nishi Grady Albatross Rev.c _______ _______ A5 size ’96/08/23 R Appendix d pass 0 Appendix D Working with Fonts Printer and Screen Fonts . . . . . . . . . . . . . . . . . . . . . . D-2 Available Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3 Adding More Fonts . . . . . . . . . . . . . . . . . . . . . . . . . Downloading fonts . . . . . . . . . . . . . . . . . . . . . . . D-6 D-6 Selecting Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L Albatross Rev.c A5 size ’96/08/23 Appendix d pass 0 Read this section if you would like to know more about fonts and see samples of the installed fonts. To select a font, use your application program. Font problems are uncommon but some may occur, such as: ❑ The printer substitutes a font other than the one you selected with your software. ❑ The printed page does not exactly match what is on screen.
Albatross Rev.c A5 size ’96/08/23 R Appendix d pass 0 d-1 screen font printer font Note: The distinction between printer and screen fonts is not as important when you are using TrueType fonts, which are included with Windows. TrueType is an outline font format that can be used by both the printer and the screen. Available Fonts The following table lists the fonts that are installed on your printer.
L Albatross Rev.
Albatross Rev.c A5 size ’96/08/23 Appendix d pass 0 Font name Bitmap font OCR B - Font name Scalable font EPSON Sans serif - Courier SWC Medium, Bold EPSON Prestige - EPSON Gothic - EPSON Presentor - I239X mode EPSON Orator - EPSON Script - Font name Bitmap font OCR B - To see the font samples, use the Test Menu in SelecType. 1. Make sure that paper is loaded. 2. Press Menu while the printer is on line. 3. Press Item until the font sample you want appears. 4.
L Albatross Rev.c A5 size ’96/08/23 Appendix d pass 0 Adding More Fonts Fonts that reside on your computer’s hard disk can be downloaded, or transferred, to the printer so they can be printed. Downloaded fonts, also called soft fonts, remain in printer memory until you turn off the printer or otherwise reinitialize it. If you plan on downloading many fonts, make sure your printer has sufficient memory. Downloading fonts Most font packages make it easy to install fonts by providing their own installer.
Proof Sign-off: Nishi Grady _______ _______ Albatross Rev.
L Albatross Rev.c A5 size 96/08/23 Appendix E A5 size pass 0 Switching between SelecType Menus The following menu maps show the possible menus and options in SelecType. KEY Pressing the Menu button displays the next menu. Pressing the Alt + Menu buttons displays the prior menu. ( ) This is only available with option.
Albatross Rev.
L Albatross Rev.
Proof Sign-off: Nishi Grady _______ _______ Albatross Rev.c A5 size ’96/08/23 R Glossary DR, pass 0 Glossary ASCII American Standard Code for Information Interchange. A standardized way of assigning codes to characters and control codes. The system is widely used by manufacturers of computers, printers, and software. auto line feed A printer feature in which each carriage return code (CR) is automatically accompanied by a line feed (LF) code. bitmap font The dot-by-dot representation of a font.
L Albatross Rev.c A5 size ’96/08/23 Glossary DR, pass 0 drum The part of the printer mechanism where the image is formed and transferred to the paper. emulation See printer emulation. fixed-width font A font whose characters are allotted the same amount of horizontal space, no matter the width of the character. Thus the uppercase M receives the same amount of space as the letter l. font A set of characters and symbols that share a common typographic design and style.
Albatross Rev.c A5 size ’96/08/23 R Glossary DR, pass 0 orientation Refers to the direction in which characters are printed on a page. This direction is either portrait, like this page, or landscape with the text printed on a page turned sideways. outline font A font whose outline is described mathematically, allowing it to be rendered (printed or drawn) smoothly at any size. PCL The command language built into the Hewlett-Packard LaserJet series printers.
L Albatross Rev.c A5 size ’96/08/23 Glossary DR, pass 0 reset To refresh the printer’s memory and erase the current print jobs. resident font A font that is stored permanently in the printer’s memory. resolution A measure of the fineness and clarity of images produced by the printer or monitor. Printer resolution is measured in dots per inch. Monitor resolution is measured in pixels. RITech Resolution Improvement Technology. A feature that smooths the jagged edges of printed lines or shapes.
Proof Sign-off: Nishi Grady _______ _______ Albatross A5 size 08-23-96 Rev.
L Albatross A5 size 08-23-96 Rev.
Albatross A5 size 08-23-96 Problem memory, 6-14 paper jam, 6-2, 6-23 print quality, 6-9 Rev.
L Albatross A5 size 08-23-96 IN-4 Rev.
EPSON OVERSEAS MARKETING LOCATIONS EPSON AMERICA, INC. EPSON UK LTD. 20770 Madrona Ave. Campus 100, Maylands Avenue, P.O. Box 2842 Hemel Hempstead, Herts, Torrance, CA 90509-2842 HP2 7TJ, U.K. Phone: (800) 922-8911 Phone: (+44) 01442 61144 Fax: (310) 782-5220 Fax: (+44) 01442 227227 EPSON DEUTSCHLAND GmbH EPSON FRANCE S.A. Zülpicher Straße 6, 68 bis, rue Marjolin 40549 Düsseldorf Germany 92300, Levallois-Perret, France Phone: (0211) 56030 Phone: 33.1.40.87.37.
EPSON® IMPORTANT NOTICE Using the LocalTalk Interface with EPL-N2000PS Version Printers The EPL-N2000PS is supplied with interfaces for connection to either EtherNet or LocalTalk Networks. As shipped, the EPL-N2000PS has the EtherNet interface installed. Should you wish to connect to a LocalTalk network, the EtherNet interface MUST be removed prior to installation of the LocalTalk interface.
