IMPORTANT NOTICE DISCLAIMER OF WARRANTY Epson America makes no representations or warranties, either express or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties ofmerchantability and fitness for a particular purpose or for any indirect, special, or consequential damages. Some states do not allow the exclusion of incidental or consequential damages, so this exclusion may not apply to you. COPYRIGHT NOTICE All rights reserved.
Important Safety Instructions Read all of these instructions and save them for later reference. Follow all warnings and instructions marked on the computer. Turn off the computer before cleaning. Clean with a damp cloth only. Do not spill liquid on the computer. Use only the type of power source indicated on the computer’s label. Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off. Do not let the computer’s power cord become damaged or frayed.
Importantes Instructions de Sécurité Lire attentivement les instructions suivantes et les conserver pour les consulter en cas de besoin. Observer soigneusement tous les avertissements et directives marques sur l’ordinateur. l l l l l l l Debrancher l’ordinateur avant de le nettoyer. N’utiliser qu’un chiffon humide. Veiller a ne pas renverser de liquides sur l’appareil. Utiliser seulement le type de source d’alimentation électrique indiqué sur l’etiquette.
Wichtige Sicherheitshinweise Bitte lesen Sie diese Sicherheitshinweise, und heben Sie sie zur späteren Verwendung auf. Beachten Sie alle Warnungen und Anweisungen, die auf dem Computer angebracht sind. Schalten Sie den Computer vor der Reinigung aus. Verwenden Sie zur Reinigung nur ein sauberes Tuch. Achten Sie darauf, daß keine Flüssigkeiten auf dem Computer verschüttet werden. Verwenden Sie nur die auf dem Typenschild des Computers angegebene Stromversorgung.
l Beachten Sie den folgenden Hinweis, wenn Sie den Computer in Deutschland in Betrieb nehmen: Beim Anschlulß des Computers an die Netzversorgung muß sichergestellt werden, dalß die Gebäudeinstallation mit einem 16 A Überstromschutzschalter abgesichert ist.
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception.
Contents Introduction Computer Features . . . . . . . . . . . . . . . . . . . . . . . . . . . Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . Power-saving Features . . . . . . . . . . . . . . . . . . . . . . . . . What This Manual Covers . . . . . . . . . . . . . . . . . . . . . . . Conventions Used in This Manual . . . . . . . . . . . . . . . Where to Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . CompuServe On-line Support . . . . . . . . . . . . . . . . . .
Chapter 2 Using Your Computer Caring for the Computer . . . . . . . . . . . . . . . . . . . . . . . . Protecting the Hard Disk . . . . . . . . . . . . . . . . . . . . . Using Energy Wisely . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Fn Key Functions . . . . . . . . . . . . . . . . . . . Using the Embedded Numeric Keypad . . . . . . . . . . . . Using the Trackpad . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4 Ins falling Optional De vices Connecting External Components . . . . . . . . . . . . . . . . . . . Using an External Monitor . . . . . . . . . . . . . . . . . . . . Using the Serial Port . . . . . . . . . . . . . . . . . . . . . . . . Using an External Keyboard or Mouse . . . . . . . . . . . . . Installing a PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and Replacing the Hard Disk . . . . . . . . . . . . . . . Installing Internal Components . . . . . . . . . . . . . . .
Appendix A Specifications CPU and Memory . . . . . . . . . . . . . . . . . . . . . . . . . Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trackpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fax/ Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction The EPSON ® ActionNote TM 800 Series notebook computers provide exceptional speed, display quality, and flexibilityall delivered by the latest in notebook computer technology. With the ActionNote’s standard memory and pre-installed M S - D O S ,® Microsoft ® Windows, TM and other software, you can run a vast array of the latest applications, utilities, and games designed for productivity and for fun.
Computer Features Upgradable 486 microprocessor with integrated math coprocessor and 8KB of internal cache memory in write-back mode 4MB or 8MB of RAM, expandable up to 24MB Backlit LCD screen; 9.5-inch monochrome version emulates VGA color with 64 shades of gray; 10.3-inch dual-scan STN and 10.
Preinstalled software on your hard disk drive, including the latest versions of MS-DOS and Microsoft Windows; on-line version of this User's Guide, Windows manual, and other manuals, providing instructions and information while you are on the road Your ActionNote has been configured for you and the hard disk drive already contains most of the software you need. In addition, drivers and utilities for your PCMCIA card slots, video system, and trackpad have already been installed.
External battery charger Security lock ActionPort Replicator Type I, II, and III PC cards. For information on purchasing optional equipment, see the Accessories icon in the About EPSON on-line group. Power-saving Features This computer complies with the United States Environmental Protection Agency’s Energy Star Program, which promotes the manufacture of energy-efficient printers, computers, and monitors.
What This Manual Covers You do not need to read everything in this book to use your computer; see the following chapter summaries: Chapter 1 provides steps for setting up your computer. Chapter 2 covers basic information about using the computer. Chapter 3 explains how to power your computer with the AC adapter or the battery and how to conserve battery power. Chapter 4 describes how to connect optional devices and upgrade your computer. Chapter 5 provides troubleshooting tips.
Conventions Used in This Manual This manual uses the following conventions in the text: ExampIe Meaning Enter Keysyou presson the keyboard Fn F10 Keysyou press at the same time; hold down the key marked Fn and press the F10 key C:\DOS Text as it appearson the screen DISKCOPY A: C: Text that you type exactly as shown Where to Get Help If you purchased your computer in the United States or Canada, EPSON provides customer support and service through a network of Authorized EPSON Customer Care Cente
You can purchase accessories, manuals, or parts for EPSON products from EPSON Accessories at (800) 873-7766 (U.S. sales only). In Canada, call (800) GO-EPSON. When you call for technical assistance, be ready to identify your system and its configuration, and provide any error messages to the support staff. See Chapter 5 for more information. If you purchased your computer in the United States or Canada, EPSON also provides Extra Care Road Service.
The fastest way to access helpful tips, specifications, drivers, application notes, and bulletins for EPSON products is through the Epson America Forum on CompuServe. To access the Epson America Forum in WinCIM, simply click on the green traffic light icon and type EPSON at the menu prompt.
Chapter- 1 Setting Up the Computer This chapter describes how to set up your computer. It covers: Opening the screen Identifying the system components Connecting the AC adapter Turning the computer on and off Reading the indicator lights Backing up files Running the Setup program Opening the Screen To open the LCD screen, slide the latches on each side of the computer’s lid and lift up the screen.
Identifying the System Components Before getting started, refer to the illustrations in this section to identify the different parts of your computer. Front View *These parts function only with the optional audio card installed.
Rear Panel and Left Side * Available only with the optional internal fax/modem installed. Using the AC Adapters The lightweight AC adapter included with your computer operates in the input ranges 100-240 VAC and 50/ 60 Hz. If you purchased your computer outside the United States, you will have the international AC adapter, which includes a ground pin and operates within the same input ranges as the lightweight adapter. EPSON also offers an auto adapter (A882241).
Connecting the Lightweight AC Adapter Connect the AC adapter cable to the DC-in port at the back of the computer. Then flip the adapter’s two prongs out of their compartment and connect the adapter to an electrical outlet. Connecting the International AC Adapter If you are using the international adapter in a country other than the one where you purchased your computer, make sure you have the correct power cable before you connect the AC adapter to an electrical outlet.
Follow these steps to connect the international AC adapter: 1. Connect the adapter cable to the DC-in port at the back of the computer. 2. Connect the power cable to the AC adapter 3. Connect the other end of the power cable to a grounded electrical outlet.
For more information about powering the computer with the AC adapter, see Chapter 3. For instructions on connecting optional equipment to your computer, see Chapter 4. Turning the Computer On and Off The first time you use your computer, the battery may not be charged; so make sure the AC adapter is connected. Then press the power button below the screen to turn on the computer.
If you plan to use another operating system, such as OS/ 2, ® U N I X , ® or Windows NT, you can install it now. See the documentation that came with it for installation instructions. Before you turn off your computer, save your data and exit the program you are currently using. Make sure the computer is not accessing data from the diskette drive, hard disk drive, or a PC card; then press the power button to turn off the computer.
Reading the Indicator Lights The indicator lights on your computer provide information about the computer’s operation.
Making Backup Copies of Your Files Before you start using your computer, it’s a good idea to make a backup copy of your hard disk drive. Use the MWBACKUP utility in the Windows Applications group or the MS-DOS BACKUP command to back up the contents of the drive. Refer to the Windows Help utility for instructions on using MWBACKUP; use the MS-DOS help utility for instructions on using BACKUP.
When to Run Setup Because your computer was set up and configured for you, the configuration information may be correct for your needs. However, you may want to run Setup to enter the correct time and date, set a password, or customize the power management features. In addition, any time you change the computer’s configuration (by installing or removing optional devices, for example), you need to run Setup to update the configuration.
Help information is available for each option. Highlight the option you want to change and press F1 to get Help. Setup lets you change or verify the settings listed in the following tables.
The table below lists the power management options. For a complete description of the power management features, see Chapter 3.
The table below lists the Setup options for advanced features and support of external devices.
If you set a system password, the computer will prompt you to enter it each time you turn on or reset your computer. If you set a Setup password, the computer prompts you to enter it each time you press F8 to run Setup. Follow the instructions in the next sections to set, delete, or change your password. Then see the instructions in Chapter 3 for entering your password when the system prompts you for it. Setting a pass word Follow these steps to set a password: 1. Highlight the Password option.
7. You can now highlight the Security option and select either SETUP , which applies the password to the Setup program, or S Y S T E M , which applies the password to all programs and data on your computer. If you choose S Y S T E M , you will be prompted to enter the password whenever you turn on the computer or try to run Setup. Deleting or changing a password If you want to delete or change a password, follow these steps: 1. Highlight the Password option.
Exiting Setup When you are ready to exit the Setup program, press ESC You see the exit menu. Press one of the following keys: 1-16 Esc Returns you to the main Setup or Power Management Setup screen F4 Saves your settings and reboots the computer F5 Loads the default settings for all the options and returns to Setup F6 Exits Setup without saving your settings.
Using Your Computer This chapter describes the daily use of your computer, including: Caring for the computer Using energy wisely Using the keyboard Using the trackpad Resetting the computer Changing the CPU speed Adjusting the LCD screen Using password security Using diskettes Using video drivers and utilities Configuring PC cards.
Caring for the Computer Following these guidelines will keep your computer working well: Keep the computer and AC adapter dry, and do not subject them to extreme heat or cold. To prevent damage to the LCD, do not place external devices on top of the computer, even if it is closed. When you are not using the serial, parallel, or video ports, or the port replicator, keep their covers closed to prevent damage to the pins in the ports. Occasionally clean the exterior with a soft, damp cloth.
Although the hard disk is very reliable, be sure to back up your files regularly. Make copies of all your system and program diskettes before copying them to the hard disk. Caution When traveling by airplane, be sure to take your computer into the passenger compartment as carry-on luggage to prevent it from being stored in an unpressurized storage area. Using Energy Wisely By purchasing this Energy Star compliant computer, you join a growing number of users concerned about conserving energy.
Using the Keyboard Although the keyboard on your computer has only 85 keys, it provides all the functions of a full-sized (101- or 102-key) keyboard. It has an embedded numeric keypad that you can access using the Num Lock or Fn keys. You can also control other features, such as the LCD screen, using the Fn key. The embedded numeric keypad and the Fn key functions are described below. Note The keyboard on the ActionNote is available with different layouts for different languages.
Using the Embedded Numeric Keypad The embedded numeric keypad (shown below) allows you to enter numbers and symbols from a keypad arrangement on the main keyboard. You use the Num Lock key to control the operation of the embedded numeric keypad. Press Num Lock to turn Num Lock mode (and its indicator light) on and off. When you use a key in the embedded numeric keypad with Num Lock mode on, you see the number or symbol for that key instead of the letter.
Using the Trackpad The trackpad on your ActionNote is a state-of-the-art pointing device which you can use to move the cursor, select text or objects, cut and paste, or choose menu items. The trackpad is compatible with most software applications that support pointing devices with PS/2 compatible drivers. To use the trackpad, simply move your fingertip across the pad in the direction you want to move the cursor. If you get to the edge of the pad, lift your finger and place it back down on the other side.
To move objects around the screen (click and drag), tap twice and then hold your finger down and move it across the trackpad. This is like double-clicking, but you leave your finger down after the second tap. You can also use the buttons below the trackpad. To customize the trackpad and learn more about its features, use the Trackpad utility in the Control Panel. Resetting the Computer If necessary, you can reset the computer without turning it off by pressing a combination of keys.
Changing the CPU Speed Your computer’s processor can operate at two speeds: fast or slow (8 MHz). The slow speed is available to provide compatibility with older application programs, such as those that are copy-protected or have a specific timing requirement. You may also want to select the slower speed to save power when you are using programs that do not require a high processor speed. Your computer is set up to start at fast speed. If you want to switch to the slower speed, you can do so using Setup.
If you want to use a system or Setup password, run the Setup program as described in Chapter 1 to enter, change, or delete the password. When the computer prompts you to enter a password, see the next sections. Note Remember that once you set a system password, you cannot access your system unless you enter it correctly. Write down your password and keep it in a safe place. If you forget your password, call the EPSON Connection for assistance.
Entering a Setup Password When you have defined a Setup password, the computer prompts you for it only after you have pressed F8 to enter Setup. After you press F8 but before you see the main Setup screen, you see a message prompting you to enter your password. Type your password and press Enter. (The screen does not display the characters you type.) Then you see the Page 1 Setup screen. If you type your password incorrectly, the computer allows you three tries to retype it correctly.
To insert a diskette, hold it with the label facing up and the shutter leading into the drive. Slide it into the drive until it clicks into place. To remove the diskette, make sure the diskette drive light is off; then press the release button. When the diskette pops out, remove it and store it properly. Caution Never remove a diskette or reset or turn off the computer while the diskette drive is being accessed; you could lose data. Also, be sure to remove the diskette before you turn off the computer.
Using Video Drivers and Utilities Your system includes high-resolution video display drivers for Windows installed on your hard disk drive. You can use these drivers to display in resolutions up to 1024 x 768 in 16 colors on an external monitor. To select these drivers, you can use the Windows Setup utility or the ChipsCPL utility in the Windows Control Panel. ChipsCPL allows you to select the resolution (screen size), color, and font size for your display.
Your system also includes two DOS video utilities, SETVGA and SETCOL, located in the C:\ UTIL directory. For more information, type one of the following commands and press Enter at the DOS prompt in the C:\ UTIL directory: SETCOL SETVGA Configuring PC Cards Whenever you turn off or reset your computer, you see a prompt asking if you want to load the PC card drivers. You must load the drivers (the default setting) if you are going to use a PC card.
Using CardSoft The PCMCIA driver and utilities, collectively called CardSoft, help you configure and manage PC cards in the MS-DOS environment. The CardSoft programs are located in the CARDSOFT directory on your computer’s hard disk drive. The following drivers and utilities are already included in the CARDSOFT directory: SSVADEM.EXE PCMCIA Socket Services driver CS.EXE PCMCIA Card Services driver CSALLOC.EXE (described below) ATADRV.EXE Driver for ATA Type III hard disk drive cards or flash cards MTSRAM.
CSALLOC utility CSALLOC is an MS-DOS program that scans the system for available memory, I/O port, and IRQ resources each time you start your system and maintains the information it collects in a file called CSALLOC.INI. You need to run CSALLOC only if you want to display the available system resources if you’ve changed port, IRQ, or memory settings on your system.
Configuration Utility The configuration utility allows you to customize your system or reconfigure it when you have trouble using a PC card. You can change the following configurations for your PC cards using this utility: IRQs and COM port assignment order for fax/ modem cards I/O port address, IRQ, and memory areas for network cards Addresses for ATA cards Card insertion parameters. You can also use the utility to modify the resource allocation that the program scanned when you started your system.
Note If your system is working properly, you don’t need to edit any of the PC card configurations. The Resource Allocation option on the Utility pull-down menu provides a quick view of the system resources that are available to CardSoft. You can also edit these system resources. Caution Do not change any resource allocation values unless you understand how these resources work on your system.
Note If you are using an ATA hard disk or ATA flash card, make sure your CONFIG.SYS file contains this command: DEVICEHIGH=C:\CARDSOFT\ATADRV.EXE If you are using an SRAM card, make sure the CONFIG.SYS file contains this command: DEVICEHIGH=C:\CARDSOFT\MTSRAM.EXE Both of these drivers are loaded in your computer’s CONFIG.SYS file at the factory. The following table describes the removable storage card utilities.
Using Card View CardView for Windows provides a user-friendly, graphical interface for your CardSoft applications. CardView performs the following functions: Displays detailed information about installed cards, including vendor name and type of card Reconfigures PC cards and system resources, such as modem COM ports Notifies you of any status changes for the PC cards in your system, such as when you insert or remove a card or when the software detects a configuration conflict.
Using Fax/Modem PC Cards You may need to change your port settings to use a fax/ modem PC card in your ActionNote. With the card inserted, start CardView and follow these steps to make sure the settings are correct. 1. Select View. 2. Check the COM port number, IRQ line, and base I/O port address for the fax/ modem. The settings for the EPSON fax/ modem PC card are as follows: COM3 Base I/O port address 03E8 IRQ line 7 3. In the Windows Control Panel, select the Ports icon. 4. Select COM3. 5.
If you use Instant On or the Low Battery Save to HDD options, the PCMCIA services are not reinitialized. In this case, your computer recognizes SRAM PC cards, but does not recognize most other PC cards, such as fax/ modem or LAN PC cards. To reinitialize the services, exit any application programs you are using and exit Windows. Then press Ctrl Alt Del to reboot your computer. Installing Additional PC Card Drivers and Utilities While the ActionNote is fully compatible with PCMCIA version 2.1 and JEIDA 4.
2-22 Using Your Computer
Chapter 3 Powering the Computer You can power your ActionNote with the compact AC adapter, international AC adapter, removable NiMH battery, or optional automobile cigarette lighter adapter. This chapter describes: Using the AC adapter Using the battery Conserving energy by using the computer’s power management features.
The AC adapter included with your computer is designed to operate in 100-240 VAC ranges with a frequency of 50/60 Hz. If you use the international AC adapter in a country other than the one where you purchased your computer, be sure to use the correct plug adapter to fit the electrical outlet. To connect the AC adapter, see the instructions in Chapter 1. After you turn on your computer, the Power indicator light comes on.
Low Battery Protection The ActionNote includes special power management features that protect your data when your battery runs low. When you have only a few minutes of power left, the Power indicator light flashes and the computer beeps. At this point, you should immediately save your data. To resume activity, you must either turn off the computer and replace the battery (as described below), or connect the AC adapter.
4. Press the battery release lever. Then lift the battery up and out of the case. battery release lever Caution As you handle your batteries, avoid touching the battery contacts with any metal objects, such as keys or coins because they may short out the battery’s circuits. 5. Insert the new battery into the compartment at an angle and then lower it into place. Recharging the Battery The battery that comes with your system is rechargeable.
Note You can also purchase an optional external battery charger so you can charge an extra battery while using another in your computer. To charge the battery, leave it in the computer. Then connect the AC adapter. The computer automatically charges the battery whenever the AC adapter is attached. It takes approximately 1.5 hours to charge a completely discharged battery when the computer is off or when it is in Suspend mode. If you use the system while the battery is recharging, it can take up to 2.
The computer’s charge light changes color as follows to show the battery charging status: Green-battery is fully charged Orange-battery is charging norm ally Flashing orange-the battery is not installed properly or is damaged; remove the battery, examine it, and try reinstalling it. Using the Power Management Features Your ActionNote offers a variety of automatic and manual power management features to help you conserve battery power.
The three power-saving modes are summarized in the following table: Power-saving operations Mode Entered when...
The Power Management screen also lets you do the following: Disable any or all of the power-saving modes Set individual timeout periods for the video and hard disk drive components Set up the computer to enter Suspend mode or save your data automatically when your battery power is low Enable Instant On (See Chapter 1 for information on setting the Power Management screen options.
With a fully charged battery, the system can operate in Suspend mode for several hours without losing data. To resume activity, press the Suspend/ Resume button again. The computer resumes normal operation at the point at which you suspended it. Note The Power Management option is set to AC Disabled and the Low Battery option is set to Suspend at the factory. This protects your data by allowing the system to enter Suspend mode automatically if you are running only on battery power and the battery runs low.
Your hard disk drive is partitioned at the factory so that you can use the Instant On or Save to HDD o p t i o n s . A 2 5 M B area of your disk is set aside for the saved data; this ensures that there is enough space for all memory configurations. Because this area is a non-DOS partition, it is invisible to your DOS-based software. The amount of disk space available to you for normal data storage is reduced.
Windows provides a Power icon in the Control Panel that allows you to select Standard, Advanced, or no power management modes and includes a battery status gauge. Use the Windows Power utility on-line help for more information about these features.
3-12 Powering the Computer
Chapter- 4 Installing Optional Devices This chapter explains how to connect or install these devices: External monitor Serial device External keyboard, keypad, mouse, or other PS/2 device PC card Hard disk drive Expansion memory module Higher-performance microprocessor In tern al fax/ modem. Connecting External Components You can use the ports on the back of your computer to connect an external monitor, parallel printer or scanner, serial device such as a mouse or modem, or an external keyboard or keypad.
See the instructions that came with the port replicator for information about connecting it and using it with your computer. Use the following illustration to locate the ports on the back of your computer as you connect external components. Follow these steps to connect external components: 4-2 1. Make sure both the computer and external component are turned off. 2. If necessary, open the port cover on the back of the computer. 3. Connect the component to the appropriate port. 4.
Using an External Monitor When you connect an external monitor, make sure you turn it on before you turn on the computer. Your system automatically detects the external monitor and displays your data on its screen. You can press Fn F10 to switch your display from the monitor to the LCD screen or to display on both screens simultaneously. You can also change the default display mode at start-up through the Boot Display option in Setup. See Chapter 1 for instructions.
Using an External Keyboard or Mouse You can use the external keyboard/ mouse port to connect a variety of PSI 2 compatible devices, including an external keyboard, keypad, or mouse. Your computer automatically detects and configures the device you connect (as long as the computer is off before you connect it). Note When you connect a pointing device to this port, the built-in trackpad is au tom atically disabled.
Follow these steps to install a PC card: 1. Open the door covering the PC card bay on the left side of your computer. 2. Hold the PC card so the 68-pin connector on the edge of the card faces the PC card slot and the card’s label faces up. release buttons 3. Align the card in the card guides of the appropriate slot. Then push the card gently but firmly into the slot as far as it will go. (Part of the card extends from the slot.) When you feel resistance, stop pushing; do not force it into the slot.
Caution Do not change the setting of a PC memory card’s write-protect switch while the card is installed in the computer or you may damage the card. First eject the card, then change the switch setting and reinsert it. When you want to remove the PC card, check the PC card indicator light to verify that the computer is not accessing the card. If you are using a LAN card, you may also want to log out.
Follow these steps to remove and replace the drive: 1. Turn off the computer and disconnect any external devices or cables. 2. Close the LCD screen and turn the computer over. 3. Press the latch away from hard disk drive cover and slide the cover back slightly. Then lift the cover off, as shown below.
4-8 4. Pull up on the two metal tabs to disconnect the drive, and remove it from the case. 5. Grasp the connector card by the edges and pull it away from the drive, as shown below. Set the drive aside.
6. To install a new drive, you first need to attach the connector card. Align the holes in the card with the group of 44 pins on the right side of the drive connector. The metal tabs on the card should be facing up. Make sure the connector does not cover the group of four pins on the left side of the drive connector. 7. When you are sure the holes and pins are properly aligned, carefully push the card straight onto the pins, pressing firmly on the card until it is fully seated.
8. 4-10 Insert the drive and card into the drive compartment, aligning the connector on the card with the pins in the compartment. Press down on the metal tabs until the drive is fully seated.
9. Position the drive cover over the compartment so that the small arrow on the cover aligns with the first notch in the latch. Lower the cover and then slide it until it snaps shut 10. Run Setup as described in Chapter 1 to make sure the computer recognizes your new drive. If you want to use the Instant On or Low Battery Save to HDD features, you need to run FDISK and leave sufficient space on the disk unpartitioned. The amount of space should be equal to your system memory plus 2MB.
Installing Internal Components You can easily upgrade your computer by installing the following internal components: Memory module Higher-performance microprocessor Fax/ modem. You must first remove the computer’s keyboard, as described in the following section. Caution Be sure to ground yourself when you install internal components. If you are not properly grounded, you could generate an electric shock that could damage one of the computer’s components when you touch it.
Removing the Keyboard Follow these steps to remove the keyboard : 1. Turn off the computer, remove the battery, and disconnect the AC adapter. 2. Disconnect any peripheral devices 3. Remove the plastic caps on both sides of the case below the screen. Use a small screwdriver to release each cap and then slide it off, as shown.
4. 5. 4-14 Use a small screwdriver to gently loosen the plastic strip above the keyboard. Lift up the strip and remove it from the case.
6. Gently lift the keyboard from the top edge, remove it from the case, and place it on a flat surface in front of the computer. Be careful not to pull on the keyboard cables. Replacing the Keyboard When you are ready to replace the keyboard, refer to the illustrations above and on page 4-14 as you follow these steps: 1. Carefully lift up the keyboard and position it over the case. 2. Insert the bottom edge of the keyboard into the case 3.
4. Position the plastic strip above the keyboard and snap it into place. The strip fits tightly, but it should not obstruct the function keys. 5. Slide the plastic caps over the screws on each side of the case below the screen and snap them into position. Make sure you use the correct cap for the left or right side; they will not slide into place on the wrong side. After you have replaced the keyboard, check that the function keys operate smoothly.
2. Press one of the plastic retaining clips toward the side of the socket and lift up on the edge of the memory module until it is released. (See the illustration below.) 3. Grasp the module firmly and pull it out of the socket. You are now ready to install the new memory module. Follow these steps to install the new memory module: 1. Holding the memory module with the notch on the upper right corner, align it with the connector at the edge of the socket. 2.
4. If you are finished installing internal components, replace the keyboard as described on pages 4-15 to 4-16. 5. Run the Setup program, as described in Chapter 1, to make sure your computer recognizes the new memory configuration. (As soon as you turn on the computer, it will prompt you to run Setup because of the memory size mismatch.) If you later remove or change the memory module, be sure to run the Setup program again.
Caution Removing the existing microprocessor requires the use of a chip puller. The microprocessor can be easily damaged and is expensive to replace; so if you don’t feel confident about installing it yourself, ask your Authorized EPSON Servicer for assistance. Depending on the type of microprocessor you are installing, you may need to adjust one of the processor switches. If you need to set the CPU type switch, you must do so before you install the processor chip.
Caution Make sure you ground yourself before you touch the processor chip. Then remain as stationary as possible while you install it. Do not touch the pins on the processor chip. Handle the microprocessor only by the edges of its case. 3. Position the chip puller between the processor chip and the socket. 4. Gently pull the processor chip straight up and set it aside. 5. Remove the new chip from its package and inspect the pins. If they are bent, do not install the chip.
Caution Note that two holes in the socket are labeled “pin l." If you are installing a processor chip directly in the socket, insert pin 1 in the second row of holes from the right. You will see an empty row of holes in the socket to the right of the chip. If you are installing a processor on a daughterboard, insert pin 1 in the outer row of holes. 7. When you are sure the microprocessor is positioned correctly, gently push it straight into the socket, pressing evenly on all sides.
Setting the Processor Speed, CPU Type, and Voltage Switches Check the table on page 4-18 or refer to the processor’s documentation to determine the external frequency (speed) and supply voltage of the processor you installed. If necessary, follow these steps to adjust the processor speed, CPU type, and voltage switches for the new microprocessor. 1.
2. To set the processor speed switch, use the tip of a small screwdriver or other tool to move the switch to the appropriate position. 25 3. 40 If necessary, use the tip of a small screwdriver or other tool to set the CPU type switches, located in the processor socket. Intel QFP/PGA 4. 33 Cyrix PGA Cyrix QFP If necessary, use the tip of a small screwdriver or other tool to set the voltage switch, located on the underside of the power converter board. 4.0 3.6 3.
5. If you are finished installing internal components, replace the keyboard as described on pages 4-15 to 4-16. 6. Run the Setup program, as described in Chapter 1, to update your computer’s configuration with the new microprocessor. Installing the Fax/Modem If your computer did not come with the internal fax/ modem, you can install it yourself. See the Introduction for information about obtaining optional accessories for your ActionNote computer. Follow these steps to install the fax/ modem: 4-24 1.
4. Insert the phone jack end of the fax/ modem card through the port opening and align the connector on the card with the connector on the system board, as shown: fax/modem connectors 5. Make sure the pins in the fax/ modem connector are directly over the holes in the connector on the system board. Then gently push the card straight into the connector. 6. If you are finished installing internal components, replace the keyboard as described on pages 4-15 to 4-16. 7.
Connecting a Phone Line You can connect your telephone line directly to the fax/ modem in your ActionNote with a standard RJ-11 telephone cable. Position the phone line connector so the tab faces down and aligns with the notch in the phone jack on the left side of your computer. Then insert the cable into the phone jack. (Connect the other end of the cable to the modular jack outlet for your phone line, if necessary.
Chapter- 5 Troubleshooting You probably won’t encounter any difficulties as you set up and use your ActionNote. If anything out of the ordinary happens, however, refer to this chapter for help.
If the suggestions here do not solve the problem, perform the steps below to identify your system and make a note of any error messages your computer displays. Then contact your Authorized EPSON Servicer or call the EPSON Connection at (800) 922-8911 (in the U.S.) or (800) GO-EPSON (in Canada).
Software versions In Windows applications, select About from the Help menu, or read the version number from the banner screen displayed when the program starts, or check your software manual. MS-DOS version In Windows, select the MS-DOS Prompt icon. When the MS-DOS prompt appears, type V ER and press Enter to display the MS-DOS version number. CONFIG.SYS In Windows, use the Sysedit utility in the Applications group to see a list of the system configuration commands in the file.
Note Your hard disk drive includes a C:\ BACKUP directory containing important system configuration files. If you need to restore the original versions of these files, use DOS or the Windows File Manager to copy them from the BACKUP directory. Copy CONFIG.SYS and AUTOEXEC.BAT to C:\ Copy *.INI to C:\WINDOWS. Error Messages Your computer’s built-in memory (ROM) contains a series of diagnostic programs, called power-on diagnostics, which your computer runs automatically every time you turn it on.
The Computer Won't Start If your computer does not start when you press the power button, try the following: 1. Check the Power light. If the light is not on, go to step 3. If it is on, check the Suspend light. If the light is on, press any key. If it is flashing, press the Suspend/ Resume key. 2. Check the Charge light. If it is flashing orange, the battery may be damaged or incorrectly installed. 3. Press the power button to turn off the computer.
3. If the charge light is flashing orange, the battery may not be installed properly. Try removing and reinstalling it according to the instructions in Chapter 3. 4. Connect the AC adapter to the computer and plug the adapter into an electrical outlet. Turn on the computer and see if it works using the AC adapter. 5. If the computer does not work with the AC adapter, see “AC Adapter Problems.
AC Adapter Problems If the computer does not work properly with the AC adapter, check the power light. If it is on, the AC adapter is supplying power to the computer and charging the battery. If it is not on, follow these steps to find the problem: 1. Disconnect the AC adapter and then reconnect it 2. Make sure the AC adapter is securely connected to the computer and the electrical outlet. 3. If the connections are secure, check the electrical outlet to make sure it is supplying power.
4. You may have set a timeout period for the LCD screen in Setup or with the Windows ChipsCPL utility. This turns off the screen automatically after a specified period of time has elapsed with no system activity. Press any key to restore the display. (See Chapters 1 and 3 for information about the power management options, and Chapter 2 for information on the ChipsCPL utility.
6. If the monitor still does not work, turn off both the computer and the monitor. Then check the electrical outlet for power. Plug a lamp into the outlet and turn it on to see if the outlet supplies power. 7. If the outlet works and an image still does not appear on your monitor when you turn on the computer, contact your Authorized EPSON Servicer or the EPSON Connection. The Computer Locks Up If the computer locks up, try the following: 1. Some operations take longer than others to perform.
Password Problems If you set a password and you have trouble using it, try the following: 1. If you type the password and then see the password prompt again, type the password again and press Enter. If you type it incorrectly three times, you must turn off the computer, wait 5 seconds, and try again. 2. If you know the current password but you want to change or delete it, see Chapter 1 for instructions. 3. If you have forgotten your password, call the EPSON Connection for assistance.
External Pointing Device Problems If your external keyboard, mouse, or other PS/ 2 compatible pointing device does not work properly, try these solutions: 1. Did you install any necessary drivers and load them into your computer’s memory? See the documentation that came with your device for instructions. 2. Your computer’s built-in trackpad is automatically disabled when a device is connected to the external keyboard/ mouse port.
Diskette Problems If you have trouble accessing data on a diskette, follow these steps to identify the problem: 1. Is the diskette properly inserted in the drive? Remove the diskette and make sure it is inserted with the label facing up. 2. Are you using the right type of diskette for your drive? The 3.5-inch drive in your computer can read either 720KB or 1.44MB diskettes. 3.
Diskette Drive Problems If you are having problems with the diskette drive, check the following: 1. If the drive does not seem to be working as it should, try performing a similar operation with a diskette in another computer’s drive, if you have access to one. 2. If the drive is making loud or unusual noises, stop the current operation immediately and contact your Authorized EPSON Servicer or the EPSON Connection.
Software Problems If you are having trouble with an application program, try the following solutions: 1. If the application program does not start, check that you are following the correct procedure for starting the program, and that it is installed correctly. 2. If the program is running, see if it includes on-line help to assist you in diagnosing the problem. 3. Your computer can run at either high speed or low speed.
Printer Problems You can solve most printer problems by following the instructions in your printer manual. If you have just connected the printer, check that the printer has power and is properly connected to the computer. If you have a serial printer or if you have problems feeding paper, check the printer manual for the correct DIP switch settings and for serial operation settings. Check the settings in your software to make sure the correct port is selected.
Fax/Modem Problems If you are having trouble using your fax or modem software, see their respective software manuals for information. Also check the memory address (COM port) Fax/Modem option in Setup. It should match your fax and modem software programs. In sure you are using the correct baud rate for you are attempting. setting in the the setting in addition, make the transmission If you are using a PC card fax/ modem, see Chapter 2 for configuration instructions.
3. If you inserted a RAM or hard disk card, did you format it? Like a diskette, a new PC RAM or hard disk card may need to be formatted (initialized) before you can use it. See the documentation that came with the card for instructions. 4. Is your PC card compatible with the ActionNote? The PC card slots on your computer support PCMCIA version 2.1 or earlier and accept up to two Type I or II cards, or one Type III card.
Be sure to save your changes to both files and then reboot your system for the changes to take effect. Note You can also rename your modified CONFIG.SYS, AUTOEXEC.BAT, and/ or Windows.INI files and then copy backup versions of your original files from the C:\ BACKUP directory. Copy the CONFIG.SYS and AUTOEXEC.BAT files to C:\, and copy the Windows .INI files to the C:\ WINDOWS directory. 6.
Appendix A Specifications CPU and Memory CPU Upgradable 486 microprocessor installed in a PGA socket; includes 8KB of internal cache in write-back mode and integrated math coprocessor System speed Fast speed and slow speed (8 MHz) available; speed selection through Setup Memory 4MB RAM soldered on the system board; configuration may include additional memory module; expandable up to 24MB using a 4, 8, 16, or 20MB memory expansion module ROM 128KB Flash ROM device containing the system and video BIOS
Controllers Video Chips and Technology® 65535 video controller; 32-bit local bus interface to the microprocessor; supports enhanced video modes on an external monitor; supports resolutions from 640 x 480 in 256 colors on the color LCD and up to 1024 x 768 in 16 colors on an external monitor; automatic external monitor detection; simultaneous display with LCD screen using Fn F10 command or software Diskette drive Built-in super I/O controller for one internal 3.
Interfaces External VGA Auto-sensing, 15-pin, D-sub, female connector for analog monitor Parallel Centronics ® compatible; 25-pin, D-sub, fern ale connector; standard S-bit parallel; supports standard (AT compatible) and bidirectional (PS/2 compatible) modes Serial RS-232C, programmable, asynchronous, 9-pin, D-sub male connector External keyboard/ mouse Auto-sensing, 6-pin, mini-DIN connector for a PSI 2-type external keyboard, keypad, or pointing device Phone jack Standard RI-11 connector with op
Fax/Modem Optional internal 14.4 baud send/ receive fax/ modem Volume Control Knob adjusts sound of internal speaker or audio card (if installed) Mass Storage Hard disk drive One removable internal IDE hard disk drive, 2.5-inch form factor; maximum height 19 mm; Setup automatically recognizes and configures drives that support IDE interface Diskette drive Internal 3.5-inch diskette drive; 720KB or 1.
Software See the Software Support icon in the About EPSON on-line group for the latest information about the software included with your system and installed on the hard disk drive Power Sources Battery Rechargeable 12 Volt NiMH battery; current regulation by thermistor AC adapters Lightweight AC adapter (A882051) International AC adapter (A882101) AC connection 2 folding connectors 6 ft (2 meter) cable DC cable 6 ft (2 meters) 6 ft (2 meters) Input voltage 100 VAC to 240 VAC 100 VAC to 240 VA
Caution Use only the adapters and replacement batteries designed for use with the ActionNote 800 series (lightweight AC adapter model number A882051, international AC adapter model number A882101, auto adapter model number A882241, and battery A882291).
Optional Equipment 4MB, 8MB, 16MB, or 20MB memory expansion module Higher-performance microprocessor Hard disk drive upgrades in various capacities 14.4 internal fax/ modem 16-bit stereo audio card Additional NiMH batteries Extra AC adapter or international AC adapter Adapter for an automobile cigarette lighter External battery charger External keyboard Numeric keypad PCMCIA Type I, II, and III cards including flash RAM, SRAM, modem, fax/ modem, and LAN cards ActionPort Replicator.
A-8 Specifications
Appendix B Fax/Modem Command Set This appendix summarizes the built-in set of commands for the ActionNote fax/ modem. These commands are compatible with the Hayes ® S m a r t m o d e m ® series. The fax/ modem comes with software that you can use to manage your data and fax communications most of the time. You may not need the commands listed in this appendix unless the software program instructs you to use them in certain situations. The following table lists the specifications for your fax/ modem.
AT Commands B-2 Command Description +++ Escape code A/ Repeat last command string AT Attention A Answer immediate (incoming call) B0 CCITT V.
AT commands (continued) Command Description x3 Enable extended result codes (O-5, 7, 10) x4 Enable all result codes Y0 Disable long space disconnect Y1 Enable long space disconnect Z0 Software reset; recalls user configuration 0 Z1 Software reset: recalls user configuration 1 &C0 DCD signal always on &C1 DCD signal on when carrier present &DO lgnore DTR signal &D1 Returns to command mode when an on-to-off DTR transition occurs &D2 Hangs up and returns to command mode when an on-to-off
AT commands (continued) Command Description &W1 Save storable parameters as user configuration 1 &Y0 Load user configuration o on power up &Y1 Load user configuration 1 on power up &Zn=x Store phone number x in location n (n=0-3) Dial Modifiers Description Modifier ! Hookflash (0.
AT S registers (continued) Command Description Range Unit S10 Carrier loss disconnect 1-255 1/10 sec S11 Tone duration and spacing 10-255 Escape guard time 0-255 1/1000 sec 1/50 sec 095 S12 S13 Reserved - - - S14* Option register Reserved None - AAH - - - - - - - - - S15 S16 Default 014 050 S17 Self-test register Reserved S18* Self-test timer value - - - S19 Reserved - - - S20 Reserved - - - S21* Option register None - 00H S22* Option register None
Fax Commands Fax command Function +FCLASS=n Select service class +F? Report active configuration +F? Report + FAA=n Data/fax auto answer +FF Enhanced flow control +FTS=n operating capabilities Stop transmission and wait +FRS=n Receive silence +FTM=n Transmit data +FRM=n Receive data +FTH=n Transmit data with HDLC framing +FRH=n Receive data with HDLC framing Result Codes Word Number Description OK 0 Command executed CONNECT 1 Connect at 300 bps RING 2
Epson America [USA) Epson America, Inc. 20770 Madrona Avenue Torrance, CA 90509-2842 Tel: (310) 782-0770 Fax: (310) 782-5051 EPSON Connection Tel: (800) 922-8911 (in U.S.) (800) GO-EPSON (in Canada) EPSON DirectSM P.O. Box 2858 20770 Madrona Avenue Torrance, CA 90509-1111 Computer system sales: Tel: (800) 374-7300 (310) 782-5478 Fax: (310) 782-4455 Epson America (International) Epson Latin America Miami, FL, USA Tel: (305) 265-0092 Fax: (305) 265-0097 Epson Mexico, S.A. De C.V. Mexico, D.F.
EPSON U.S And International Marketing Locations Epson Deutschland GmbH Zülpicher Straße 6, 40549 Dusseldorf 11 Germany Phone: (49) (211) 56030 Fax: (49) (211) 504-7787 Epson France S.A. B.P. 320, 68 Bis Rue Marjolin 92305 Levallois-Perret Cedex, France Phone: (33) (1) 4087-3737 Telex: (42) 610657 Fax: (33) (1) 4737-2240 Epson Iberica, S.A. Avda. de Roma 18-26 08290 Cerdanyola de1 valles Barcelona, Spain Phone: (34) (3) 582-1500 Fax: (34) (3) 582-1555 Telex: 50129 Epson Italia s.p.a. V.le F.
—Distributors South America SISCO São Paulo, SP Brazil Tel: (5511) 549-4846 Fax: (5511) 549-4571 Siser Ltda. La Paz, Bolivia Tel: (591-2) 34-32-45 Fax: (591-2) 35-92-68 McSilver, S.A. Bogota, Colombia Tel: (571) 270-4303 Fax: (571) 230-9205 Merisel Colombia Bogota, Colombia Tel: (571) 257-7800 Fax: (571) 610-0674 C.I.L.D.S.E. Quito, Ecuador Tel: (593) 2-54-3418 Fax: (593) 2-55-4780 Ace Computers &Electronics Georgetown, Guyana Tel: (592) 25-65-48 Fax: (592) 26-39-67 A.J.
Caribbean Caribbean Computer Systems, Ltd. Bridgetown, Barbados Tel: (809) 429-7050 Fax: (809) 429-6509 Da Costas Limited Bridgetown, Barbados Tel: (809) 427-5854 Fax: (809) 436-9870 Computer Business Systems Kingston, Jamaica Tel: (809) 925-8600 Fax: (809) 925-8115 WTG/APTEC Systems Limited Kingston, Jamaica Tel: (809) 929-9250 Fax: (809) 929-8296 Boolchand Pessomal N.V.
Index A About EPSON on-line group, Intro-2 AC adapter automobile, 1-3 connecting, 1-3-6 international, 1-3, 3-1—12 lightweight, 1-3 model numbers, A-6 precautions, 2-2 problems, 5-6—7 specifications, 3-2, A-5 using, 3-1—2 Acoustical noise, A-6 Airplane travel precautions, 2-3, A-6 Altitude, A-6 APM interface, 3-6,3-10—11 AT commands, B-2 AT S registers, B-4—5 ATA cards, 2-17 ATA disks memory addresses, 2-16 partitioning, 2-17—18 ATADRV utility, 2-18 ATAINIT utility, 2-18 Audio input/ output, 1-2, A-3 Audio
Computer (continued) starting problems, 5-4 turning on and off, 1-6 using, 2-1—21 CONFIG.
Fax/ modem, internal (continued) result codes, B-6 software, 4-26, 5-16, B-1 specifications, A-3, B-1 using, 3-1—2, 4-26 Fax/ modem PC card, 2-16, 2-20 FDISK, 3-10, 4-11 Flash cards, 2-18 Fn key functions, 2-4—5 H Hard disk cards, partitioning, 2-17—18 Hard disk drive backing up, 1-9, 2-3 connector, 4-8—9 compartment, 1-2, 4-7, 4-9, 4-11 controller, A-1—2 defining in Setup, 1-11 Instant On partition, 3-9—10 light, 1-8, 2-2, 5-13 power management, 3-7—8 problems, 5-12—13 protecting, 2-2 removing, 4-6—9 repl
Memory adding, 4-16 addresses, 2-16 cache, Intro-2, 1-13, A-1 configuring, 4-18 manager program, 2-13, 5-17 module, 4-16—18, 5-15, A-1 RAM, Intro-2, 5-4, A-1 ROM, 1-9, 5-4, A-1, A-4 specifications, Intro-2, A-1 Microphone, 1-2 Microprocessor, see Processor Monitor, see External monitor Mouse configuring, 4-4 connecting, 4-4 port specifications, A-3 problems, 5-11 MS-DOS, Intro-1-8, 5-3 MTDDRV utility, 2-18 MTSRAM.
Power (continued) problems, 5-5 sources, 3-1—6, 5-5, A-5 Power Management APM interface, 3-6, 3-10—11 automatic, 3-7—8 description, Intro-4, 3-6 features, 3-6 Idle mode, 3-7—8 Low Battery, 1-12, 3-3, 3-9 manual, 3-8—9 maximum battery mode, 3-8 maximum performance mode, 3-8 options, 1-12, 3-9, 5-8, 5-13 Setup screen, 1-12, 3-7—8 Standby mode, 3-7-8, A-2 Suspend mode, 3-3, 3-7—10 timeout periods, 3-9, 5-8, 5-13 Power-on diagnostics, 1-6, 1-10, 5-2, 5-4 Printer problems, 5-14—15 Processor clock, 3-7-8 CPU type
Setup program (continued) power-on password, 1-11, 1-13—15 prompt, 1-10 running, 1-9—16 serial port, 1-13 setup password, 1-11, 1-13—15 starting, 1-10, A-4 system date, 1-11 system time, 1-11 when to run, 1-10 SMARTDRV.EXE, 5-17 Software audio applications, C-1—2 manuals, Intro-3 preinstalled, Intro-3, A-5 problems, 5-14 version numbers, 5-2—3 Speaker, 1-2, A-3 Specifications, A-1—8 Speed, see Processor speed SRAM cards, 2-17 SSVADEM.
Appendix C Using Your Audio Card The optional 16-bit stereo audio card is Business Audio and SoundBlasterPRO compatible. When the card is installed in your ActionNote, the built-in audio input and output connectors are activated, allowing you to use accessories such as an external microphone, external speakers, or headphones. If your ActionNote came with the audio card installed, your system also includes a driver and software.
Audio applications (continued) Application Description Chime Plays a selected sound at intervals of 15, 30, or 60 minutes Reminder Provides two alarms that you can set with a variety of sounds Stopwatch Makes audio announcements of the time elapsed Timer Makes audio announcements of the time remaining Setup Allows you to change your audio card settings For more information about the audio software, use the Help utility available with each application.