Using PictureMate With a Computer CPD-19730 Printed in XXXXXX XX.
Follow These Easy Steps To use PictureMate® with your computer, you’ll need to: Install the software on your computer from the PictureMate CD. Follow the steps in this booklet. Connect PictureMate to your computer. The steps in this booklet tell you how and when to connect. View the on-screen User’s Guide. Click PictureMate User’s Guide right on your computer screen for steps on using PictureMate with your computer. It’s your comprehensive guide to PictureMate.
Installing Software and Connecting PictureMate To connect PictureMate® you’ll need this cable: Type A to B USB cable If you don’t have a USB cable, you can buy one from your local computer dealer or from Epson.® See the inside back cover for details. When you’re ready to start, see the section for your computer system: For Windows,® see below. ■ For Macintosh,® see page 9.
After a moment, you see this screen: 4. Click Next.
Note: If you see a screen like this, remove your memory card from PictureMate and click the X in the upper right corner to close the screen, if necessary. Note: If you see a New Hardware Found message at the bottom of your screen, click the X in the box to close it. If you see a screen like this, click Cancel and disconnect PictureMate from your computer. Then turn off your computer and begin again at step 2.
5. When you see this screen, read the license agreement and click AGREE. You see this message: 6. Click OK to begin installing your software.
After a moment, you see this screen: 7. Make sure PictureMate is turned on, then connect the square end of your USB cable to the USB port on the back of PictureMate. Connect the flat end of the USB cable to any USB port on your computer.
Windows installs your software. 8. When you see this screen, click No if you have another printer for non-photo printing. If PictureMate is your only printer, and you only print photos, click Yes. Continue with the instructions in the next section.
Installing Additional Software for Windows 1. When you see a message that your printer driver was successfully installed, click Next. Additional software is installed. You see the Optional Software screen: 2. Click Epson Software Film Factory, then click Install on the next screen and follow the on-screen instructions. Note: If you are asked if you want to install QuickTime,® click Yes and follow the on-screen instructions. Uncheck the box for launching Film Factory™ at the end of the installation.
3. Close any open windows to return to the Optional Software screen. 4. Click Epson PhotoCenter Link, then click Add Icon on the next screen and click OK. 5. When you’re done installing software, click Exit. The registration screen appears. 6. Follow the on-screen instructions to register PictureMate. 7. Remove and store your PictureMate CD, then restart your computer.
Installing PictureMate for Macintosh 1. If you inserted a memory card, remove it from PictureMate. 2. Connect the square end of your USB cable to the USB port on the back of PictureMate. Then connect the flat end of the USB cable to any open USB port on your Macintosh. Make sure the handle is all the way down in back 3. Press the P On button to turn on PictureMate. 4. Turn on your Macintosh and wait a minute for it to start up. 5. Insert the PictureMate CD in your CD-ROM or DVD drive.
Note: If you have any problems installing the PictureMate software, see page 16. 6. Double-click the Epson CD icon to open it, then double-click Epson. You see a screen reminding you to connect PictureMate to your Macintosh. 7. Click Next. 8. When you see this screen, read the license agreement and click AGREE.
You see the Install Menu: 9. Click Install Printer Driver and Utilities. Follow the on-screen instructions to install several programs. You’ll need to enter your password, accept license agreements, and click Quit several times as you install. 10. Continue with the instructions in the next section to install additional software.
Installing Additional Software for Macintosh 1. When you return to the Install Menu, click Install Optional Software. You see this menu: 2. Click Epson Software Film Factory, then click Install on the next screen and follow the on-screen instructions. 3. Click Epson PhotoCenter Link, then click Add Icon on the next screen and click OK. 4. When you return to the Optional Software menu shown above, click Back.
5. At the Install Menu, click Install Printer Manual to install your on-screen User’s Guide. 6. When you’re done installing software, click Exit. The registration screen appears. 7. Follow the on-screen instructions to register PictureMate. 8. Remove and store your PictureMate CD, then restart your Macintosh. After you finish installing software, you must select PictureMate as your Macintosh printer. Follow the instructions below. Selecting Your Printer in Mac OS X 1.
2. If PictureMate 2005 appears in the Printer List, click PictureMate 2005 and click Add. If it doesn’t appear, make sure PictureMate is turned on and connected to your Macintosh, then click Add. You see a new screen: 3. If it isn’t already selected at the top of the screen, choose EPSON USB. 4. Click PictureMate 2005, then click the Add button. You see the Printer List with PictureMate 2005 added: 5. Close the Printer Setup Utility or Print Center.
You’re ready to print your photos! Insert your memory card or open your photo file on your Macintosh, as described in the on-screen User’s Guide. Double-click the PictureMate User’s Guide icon on your screen to open the User’s Guide.
Help With Software Installation Problems If you have problems installing the software, try these suggestions: ■ ■ ■ ■ ■ Carefully follow the instructions on the Start Here sheet and in this booklet. Don’t connect PictureMate to your computer until you are instructed to. Then connect the USB cable securely at both ends. Close your other programs, including any screen savers and virus protection software, and install the PictureMate software again.
Follow These Easy Steps To use PictureMate® with your computer, you’ll need to: Install the software on your computer from the PictureMate CD. Follow the steps in this booklet. Connect PictureMate to your computer. The steps in this booklet tell you how and when to connect. View the on-screen User’s Guide. Click PictureMate User’s Guide right on your computer screen for steps on using PictureMate with your computer. It’s your comprehensive guide to PictureMate.