Start Here Card

ManualsBrandsEpson ManualsPrintersEpson Epson PictureMate Flash Compact Photo Printer - PM 280

2 Plug

1 Connect the power

PictureMate.

2 Connect the power

cable to the power

adapter.

3 Plug the other end

of the power cable

into a power outlet.

4 Flip the handle to

5 Open the paper

6 Press the On

After a moment, you

this on the photo

viewer screen:

Now you can install your

3 Install

Photo

1 Open the cartridge

*410693400*

Start Here

Follow these steps to set up your PictureMate

Snap

or Flash and print–no computer required!

Note: PictureMate Snap is shown throughout, but the steps are the

same for PictureMate Flash. To print from your computer, see the

Basics book and your CD after completing these steps.

1 Unpack

PictureMate comes with all these items in the box.

1 Remove all the tape and packing material from the

outside of PictureMate.

2 Open the cartridge door

on the back of

PictureMate.

3 Remove the packing

material from inside the

cartridge slot.

4 Close the cartridge door.

PictureMate

Initial PictureMate

photo cartridge

PictureMate

photo paper

Basics book Printer Software CD

Power adapter Power cable

PictureMate Snap

(PM 240)

PictureMate Flash

(PM 280)

Summary of content (6 pages)

PAGE 1
Start Here ® PictureMate Snap (PM 240) PictureMate Flash (PM 280) 2 Plug 1 Connect the power PictureMate. 2 Connect the power cable to the power adapter. 3 Plug the other end of the power cable into a power outlet.
PAGE 2
Plug In and Turn On 1 Connect the power adapter to the back of PictureMate. 2 Connect the power cable to the power adapter. 3 Plug the other end of the power cable into a power outlet. 4 Flip the handle to the back. 5 Open the paper support. 6 Press the On button to turn on PictureMate. After a moment, you see this on the photo viewer screen: Now you can install your initial photo cartridge.
PAGE 3
Turn On 2 Slide the cartridge lever left to the Release position. 3 Remove the initial photo cartridge from its package. to the back of Caution: Do not install a different PictureMate cartridge for initial setup. Install only the initial photo cartridge that came with PictureMate. back. 4 Slide the cartridge straight into the slot, label side up, until it clicks into place. It will not go in all the way. 5 Slide the lever all the way right, to the Lock position.
PAGE 4
Load Paper PictureMate comes with genuine Epson® glossy photo paper made especially for printing lab quality photos. Caution: Don’t load or print on plain paper; this may damage PictureMate. 1 Move the handle to the back and open the paper support, if necessary. 2 Press the Open button to open the output tray. 3 Slide the edge guides outward. 4 Load up to 20 sheets at a time. Fan the sheets to slightly separate them.
PAGE 5
photo paper may damage 1 Remove the memory card containing photos from your digital camera. Insert a Memory Card 2 Select All Photos 1 Press the Select All selection button. (The selection button is the the photo 2 To print more the photos, press the number. selection button 3 Press Proceed. 4 To change the photo, press OK to increase 5 Continue with Insert your memory card into the correct slot on PictureMate.
PAGE 6
Select All Photos 1 Press the Select All selection button. (The Select All selection button is the left button beneath the photo viewer screen.) 2 To print more than one copy of all the photos, press OK to increase the number. Press the Copy selection button to decrease it. 3 Press Proceed. 4 To change the number of copies of an individual photo, press or to select the photo. Then press OK to increase the number, or Copy - to decrease it.