INSTALLATION MANUAL ELPMBUNI EPSON AMERICA, INC. INDIANAPOLIS DISTRIBUTION CENTER 2350 Stafford Road Suite 101 Plainfield, IN 46168 IN-ELPMBUNI.
ELPMBUNI Table of Contents Warranty ............................................................................................................................................................................................... - 3 Contact Premier Mounts ....................................................................................................................................................................... - 3 Warning Statements .................................................................
ELPMBUNI Warning Statements WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
ELPMBUNI Parts List NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700). Upper Assembly (Qty 1) Mounting Bracket (Qty 1) Plastic Barrel Caps (Qty 4) M3 Flat Washers (Qty 4) Note: Must be used with the M3 x 16 Phillips screws.
ELPMBUNI ELPMBUNI Universal Mount Assembly A B C D E F G H I J K L M Single Wooden Stud Mounting Points Solid Structure Mounting Points Ceiling Plate Allen Wrench Height Adjustment Screws Tension Knobs Safety Knob Security Screws Leveling Barrels Universal Mounting Bracket Leg Assembly Projector (Not Supplied) Tri-Lock Opening Option 1 A B NOTE: The four (2-piece) leg assemblies can be used as single leg or any combination of single and dual legs together as shown in Options 1 and 2.
ELPMBUNI Projector Preparation WARNING: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the projector. CAUTION: THE PROJECTOR IS FRAGILE; HANDLE WITH CARE AT ALL TIMES. NOTE: 1. 2. 3. Review the projectors manufacture’s operation manual and refer to the ceiling installation instruction.
ELPMBUNI 4. 5. Separate the upper assembly from the projector mounting bracket by slightly loosening the two tension knurl knobs to create free play between the bracket tri-lock assembly and the upper section tri-lock assembly points. Next loosen the safety screw knurl knob far enough to allow the two parts to be rotated 180° apart and separate.
ELPMBUNI Securing the Bracket to the Projector NOTE: 1. 2. The two-piece mounting legs are designed to allow routing of the legs around critical ventilation screens on the base of the projector as shown. You may also reduce the two-piece leg to a one-piece leg as shown for a better overall fit to the projector. Locate the mounting points on the bottom of the projector and use the appropriate number of mounting legs.
ELPMBUNI NOTE: If your projector model is not shown, when arranging the leg combination, simply ensure access to filters and lamp housings when aligning brackets. This mount works with all sub-25 pound projectors.
ELPMBUNI Top View Front View PowerLite 732c, 737c, 740C, 745C, 750c, 755c, 760c, 765c Hardware: M4 x 12mm (Qty 3) Installation Manual Page - 11 -
ELPMBUNI PowerLite 7800p, 7850p, 7900p Hardware: M4 x 12mm (Qty 4) PowerLite 61p, 81p, 821p Hardware: M4 x 12mm (Qty 4) Page - 12 - Installation Manual
ELPMBUNI PowerLite S1, S1+ Hardware: M4 x 12mm (Qty 3) PowerLite 6100i Hardware: M4 x 12mm (Qty 4) Installation Manual Page - 13 -
ELPMBUNI Leveling the Mounting bracket 1. 2. Rotate the leveling barrels to level the mounting bracket next, position the mounting bracket so that it avoids most, if not all, ventilation points (including lamp & filter access doors). When the position desired is achieved tighten the mounting hardware to the projector then tighten the hex head leg screws with the Allen wrench (supplied) (Figure 8 and Figure 9). CAUTION: Secure but do not over-tighten the mounting hardware.
ELPMBUNI Securing the Upper Assembly Ceiling Plate 1. 2. 3. 4. Review your projector’s distance calculation to determine what distance is recommended from the front of the lens to the edge of the screen for best picture ratio. Locate the inverted projectors top of the lens point to a point centered horizontally on the screen and no higher then the top image edge of the screen). It is normally better to have the top edge of the lens as close to parallel with the top image edge of the screen as well.
ELPMBUNI Low-Profile Installation 1. 2. 3. If your installation requires the overall height of the mount to be less that the approximate 9” shown with the standard mount assembly, you can convert the height to only 2 ½” by simply removing the adjustment channel as shown. Once the extension channel is removed, attach the upper ceiling plate to the ceiling. Once attached install the bell housing assembly to the upper ceiling plate as shown (Figure 10, Figure 11, and Figure 12).
ELPMBUNI Wood Stud Ceiling Plate Ceiling Structure Wood Screws Figure 11 Allen Wrench Wood Stud Ceiling Structure Secure the Bell Housing with Two M8 x 16mm Screws and Flat Washers Only Attach Bell Housing to the Ceiling Plate Figure 12 NOTE: Do not use the star washers on a close ceiling application.
ELPMBUNI Securing the Projector to the Upper Assembly 1. 2. 3. 4. 5. Make sure the three-knurl knobs are loosened to fully expose to the “tri-lock” mounting plate in the base of the upper assembly. Carefully lift the projector and insert the mounting bracket mating special tri-lock cutout into the mating portion of the upper assembly. Once inserted rotate the projector and mounting bracket 180° and secure the rear safety knob first to prevent further rotation of the bracket in the upper assembly.
ELPMBUNI Final Adjustments 1. 2. 3. 4. 5. With the projector secured in the mount and power on and signal supplied to the projector you can now proceed with the final height, tilt, and roll and yaw to optimize the projected image. The height can be adjusted by slightly loosening the two 8mm height adjustment screws and raising or lowering the projector (Figure 14). Once the height is achieved tighten the two screws.
ELPMBUNI Installing the Plastic Caps 1. Once all the final adjustments have been done, install the plastic caps on the leveling barrels (Figure 17).
