User’s Manual for ELPLL02 Long-Focal Length Zoom Lens • This long-focal length zoom lens is designed for use only with EPSON multimedia projectors. • It makes it possible to increase the distance between the projector and the screen. • Please read this manual completely before use to assure maximum performance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice.
1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting.
2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installation, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your particular projector model. 2-1 Removing the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case.
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the zoom lens (1) Mounting the zoom lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top. Seal Rear lens cap 12 02_LTZL_DTP_E.pm6 Page 12 01.2.15, 4:20 PM Adobe PageMaker 6.
(2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates normally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 13 02_LTZL_DTP_E.pm6 Page 13 01.2.15, 4:20 PM Adobe PageMaker 6.
4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 2. Zoom ratio 3. f number 4. Projection size 5. Mass 68.3 to 116.2 mm 1.7 x 2.14 to 2.98 60 to 300 inches 2100 g 4-2 Appearance with zoom lens mounted About 505mm 15 02_LTZL_DTP_E.pm6 Page 15 01.2.15, 4:20 PM Adobe PageMaker 6.
User’s Manual for Long Throw Zoom Lens ELPLL03 • This long throw zoom lens is designed for use only with EPSON multimedia projectors. • It makes it possible to increase the distance between the projector and the screen. • Please read this manual completely before use to assure maximum performance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice.
1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long throw zoom lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting.
2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installation, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your particular projector model. 2-1 Remove the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case.
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the zoom lens (1) Mounting the zoom lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top. Seal Rear lens cap 12 02_LTZL_DTP_E.pm6 Page 12 01.2.15, 4:23 PM Adobe PageMaker 6.
(2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates normally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 13 02_LTZL_DTP_E.pm6 Page 13 01.2.15, 4:23 PM Adobe PageMaker 6.
4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 2. Zoom ratio 3. f number 4. Projection size 5. Mass 144.1 to 194.5mm 1.35 x 2.60 to 3.27 80 to 300 inches 2100 g 4-2 Appearance with zoom lens mounted About 505mm 15 02_LTZL_DTP_E.pm6 Page 15 01.2.15, 4:23 PM Adobe PageMaker 6.
User’s Manual for ELPLR01 Rear Projector wide Lens • This wide-angle lens is designed for use only on EPSON multimedia projectors. • This lens is designed for use only on rear projection and rear projection box systems. • Please read this manual completely before use to assure maximum performance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice.
1. Before mounting the wide-angle lens 1-1 Safety precautions Warning Be sure to screw the Rear Projector wide lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting.
2. Mounting the rear-projection wide-angle lens Warning Be sure to disconnect the power cable before installation, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your particular projector model. 2-1 Removing the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case.
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the rear-projection wide-angle lens (1) Mounting the rear-projection wide-angle lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the rear projector wide lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top. Seal Rear lens cap 14 02_RPWL_DTP_E.pm6 Page 14 01.2.15, 4:17 PM Adobe PageMaker 6.
(2) Adjusting the wide lens for a rear projector • This lens must be adjusted to match the screen size. Adjust the lens as follows, before installing the front case. 1. Turn the lens shift button to move the lens all the way down. 2. Loosen the 2 focus ring mounting screws by using the hex wrench that came in the same package. 3. Loosen the 2 resolving plane correction ring mounting screws with the hex wrench. 4. Turn on the projector power. 5.
(3) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates normally. 16 02_RPWL_DTP_E.pm6 Page 16 01.2.15, 4:17 PM Adobe PageMaker 6.
4. Rear-projection wide-angle lens specifications 4-1 Lens specifications 1. Focal length 2. f number 3. Projection size 4. Mass 27mm 2.3 60 to 100 inches 1600 g 4-2 Appearance with rear projector wide lens mounted About 455mm 18 02_RPWL_DTP_E.pm6 Page 18 01.2.15, 4:17 PM Adobe PageMaker 6.
User’s Manual for ELPLS01 Standard Lens • This standard lens is designed for use only with EPSON multimedia projectors. • Please read this manual completely before use to assure maximum performance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to help prevent damage or injury, the following symbols are used in the manual.
1. Before mounting the standard lens 1-1 Safety precautions Warning Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting.
2. Mounting the standard lens Warning Be sure to disconnect the power cable before installation, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your particular projector model. 2-1 Removing the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case.
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the standard lens (1) Mounting the standard lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the standard lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top. Seal Rear lens cap 12 02_SL_DTP_E.pm6 Page 12 01.2.15, 4:19 PM Adobe PageMaker 6.
(2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates normally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 13 02_SL_DTP_E.pm6 Page 13 01.2.15, 4:19 PM Adobe PageMaker 6.
4. Standard lens specifications 4-1 Lens specifications 1. Focal length 2. Zoom ratio 3. f number 4. Projection size 5. Mass 49.2 to 68.9 mm 1.4 x 1.84 to 2.36 30 to 300 inches 1300 g 4-2 Appearance with standard lens mounted About 475mm 15 02_SL_DTP_E.pm6 Page 15 01.2.15, 4:19 PM Adobe PageMaker 6.
User's Manual for the ELPLW01 Wide Zoom Lens • This wide zoom lens is designed for use only with EPSON multimedia projectors. • It makes it possible to decrease the distance between the projector and the screen. • Please read this manual completely before use to assure maximum performance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice.
1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting.
2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installation, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your particular projector model. 2-1 Removing the current lens (1) Remove the front case. 1. Remove the three mounting screws, and pull off the front case.
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the zoom lens (1) Mounting the zoom lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading "UPPER" is on top. Seal Rear lens cap 12 02_STZL_DTP_E.pm6 Page 12 01.2.15, 4:22 PM Adobe PageMaker 6.
(2) Mounting the front case 1. Set the front case into position and tighten the three screws. This completes installation. • Turn on the power and verify that the projector operates normally. Memo • Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. • When handling the zoom lens, take care not to catch your finger between the lens and the tabletop. 13 02_STZL_DTP_E.pm6 Page 13 01.2.15, 4:22 PM Adobe PageMaker 6.
4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 2. Zoom ratio 3. f number 4. Projection size 5. Mass 37.9 to 45.5 mm 1.2 x 2.34 to 2.65 60 to 200 inches 2600 g 4-2 Appearance with zoom lens mounted About 480mm 15 02_STZL_DTP_E.pm6 Page 15 01.2.15, 4:22 PM Adobe PageMaker 6.