PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.book Page 2 Thursday, December 6, 2007 11:25 AM Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.book Page 5 Thursday, December 6, 2007 11:25 AM Problem Solving 55 What To Do When the Lights Come On or Flash Solving Picture Problems Solving Remote Control Problems Where To Get Help 55 56 59 60 Specifications 61 General Lamp Remote Control Dimensions Electrical Environmental Safety Compatible Video Formats ESC/VP21 Command Codes 61 61 61 62 62 62 62 63 65 Notices 67 Important Safety Information FCC Compliance Statement Declaration of Conformity Epson America, Inc.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.book Page 7 Thursday, December 6, 2007 11:25 AM Introduction The PowerLite® Pro Cinema 810 projector lets you enjoy theater-quality images in the relaxing environment of your own home.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.book Page 11 Thursday, December 6, 2007 11:25 AM Optional Accessories Epson provides the following optional accessories for the projector: Product Part number Replacement lamp (ELPLP39) V13H010L39 Air filter replacement (ELPAF09) V13H134A09 Projector mount ELPHB800 Kensington security lock ELPSL01 S-video cable ELPSV01 You can purchase accessories from an Epson authorized reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766).
PowerLite Cinema Pro 810.book Page 12 Thursday, December 6, 2007 11:25 AM Using This Manual This book contains all the information you need to use the projector, in addition to basic setup and maintenance instructions, troubleshooting tips, important safety instructions, specifications, and warranty information. Please follow these guidelines as you read through the manual: Warnings: Must be followed carefully to avoid bodily injury. Cautions: Must be observed to avoid damage to your equipment.
PowerLite Cinema Pro 810.book Page 13 Thursday, December 6, 2007 11:25 AM Setting Up the Projector Follow the instructions in this section to choose a location for the projector, connect the cables, and display an image. Choosing a Location You can install the projector for various viewing setups, as shown below.
PowerLite Cinema Pro 810.book Page 14 Thursday, December 6, 2007 11:25 AM Ideally, place the projector at a height where its lens is between the top and bottom of the screen. That way, you can keep the projector level and use the vertical lens shift dial to position the image. This produces the best-looking picture.
PowerLite Cinema Pro 810.book Page 15 Thursday, December 6, 2007 11:25 AM The maximum size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings and how you use the Zoom ring, the actual size may be smaller. Use this table as a rough guide for projector placement: 16:9 aspect ratio 4:3 aspect ratio Maximum diagonal Projection distance image size Projection distance Maximum diagonal image size 3.0 to 6.6 feet 30 in. (26 × 15 in.) 3.
PowerLite Cinema Pro 810.book Page 16 Thursday, December 6, 2007 11:25 AM Installing the Projector To install the projector, you first need to determine the location, based on the size of your screen (maximum diagonal image size). Use the table on page 15 as a guide to locating the projector. Note the following dimensions: ■ Distance from the center of the lens to the mounting bracket holes: 2.32 inches (59 mm), 0.34 inch (8.
PowerLite Cinema Pro 810.book Page 17 Thursday, December 6, 2007 11:25 AM You will need the optional projector mount designed for the projector. See page 11 for ordering information. Warning: When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use any type of oil or lubricant. These may cause the projector casing to crack and the projector may fall, causing serious injury and serious damage to the projector.
PowerLite Cinema Pro 810.book Page 18 Thursday, December 6, 2007 11:25 AM Connecting the Cables You can connect the projector to any type of video equipment, such as a VCR, DVD player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera. You can also connect it to a desktop or laptop PC or Apple® Macintosh® system.
PowerLite Cinema Pro 810.book Page 19 Thursday, December 6, 2007 11:25 AM For best results, connect your video equipment to the HDMI (High-Definition Multimedia Interface) port, if possible. If your equipment doesn’t support HDMI, connect it to one of the following ports (highest quality listed first): Component (for component video), S-Video, or Video (for composite video).
PowerLite Cinema Pro 810.book Page 20 Thursday, December 6, 2007 11:25 AM ■ The Trigger out port outputs a 12-volt DC signal when the projector is turned on. This lets a central control system monitor whether the projector is on or off, and can be used to raise or lower your projection screen automatically when the projector is in use. Connect a 3.5-mm mini jack to the port, as shown. Installing Batteries in the Remote Control The remote control uses 2 AA batteries.
PowerLite Cinema Pro 810.book Page 21 Thursday, December 6, 2007 11:25 AM Turning On the Projector 1. Remove the lens cap. 2. Turn on any connected equipment you plan to use. 3. Turn on the power switch on the back of the projector. Power switch 4. Press the On button on the remote control, or press the Power button on the projector. Turn on the projector Note: To keep children from turning on the projector, you can use the Child Lock (see page 31).
PowerLite Cinema Pro 810.book Page 22 Thursday, December 6, 2007 11:25 AM Turning Off the Projector 1. Turn off any equipment connected to the projector. 2. Press the Off button on the remote control, or press the Power button on the projector twice. 3. When the Ppower light stops flashing orange and stays on, turn off the projector’s power switch on the back. It is now safe to unplug the projector, if necessary. Caution: Turn off this product when not in use to prolong the life of the projector.
PowerLite Cinema Pro 810.book Page 23 Thursday, December 6, 2007 11:25 AM If you press the Source button on the projector, you see a menu of available sources. Press the u or d button to highlight a source and press the Source button Select button. If the Component source is selected, press the Compo. button on the remote control to display the following menu: Press the u or d button to highlight YCbCr or YPbPr, or select Auto so the projector can automatically detect the Component source type.
PowerLite Cinema Pro 810.book Page 24 Thursday, December 6, 2007 11:25 AM Positioning the Image If the image is not centered on the screen, use the horizontal and vertical lens shift dials to adjust its position. Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the lens position. Horizontal lens shift dial Vertical lens shift dial Note: You can display a test pattern to help adjust the image position.
PowerLite Cinema Pro 810.book Page 25 Thursday, December 6, 2007 11:25 AM Making Basic Adjustments Follow the instructions in this chapter to make basic adjustments to the image shape, size, and color, and quality. For further refinements, see “Making Detailed Adjustments” on page 33. Correcting the Image Shape If the projected image looks like or , use the Keystone function to correct its shape.
PowerLite Cinema Pro 810.book Page 26 Thursday, December 6, 2007 11:25 AM Focusing and Zooming Sharpen or reduce the focus using the focus ring. Zoom into or out of the picture using the zoom ring. Focus ring Zoom ring Wide Tele Choosing the Aspect Ratio In many cases, video signals are automatically resized to fit on your screen when Auto is selected as the Aspect setting.
PowerLite Cinema Pro 810.book Page 27 Thursday, December 6, 2007 11:25 AM If the Auto setting is unavailable, you may want to choose one of these settings: ■ Normal for standard TV broadcasts, computer images, or images with a 4:3 aspect ratio. ■ Zoom for images recorded in 16:9 (wide-screen) format. 4:3 image using Normal setting 16:9 image using Zoom setting ■ Wide if you want to expand a 4:3 image to 16:9 so it fills the whole screen.
PowerLite Cinema Pro 810.book Page 28 Thursday, December 6, 2007 11:25 AM Choosing the Color Mode You can change the Color Mode to automatically adjust brightness, contrast, and color, letting you quickly optimize the projected image for various lighting environments. You can also select a different color mode for each input source—which is useful if you view different types of images from different sources.
PowerLite Cinema Pro 810.book Page 29 Thursday, December 6, 2007 11:25 AM Adjusting the Gamma, Color Temperature, and Skin Tones To further customize the color and image quality, you can adjust the Gamma, abstract Color Temperature, and Skin Tone settings using buttons on the remote control. (Not available when you’re projecting sRGB images.) Gamma button S. Tone button ColorTemp.
PowerLite Cinema Pro 810.book Page 30 Thursday, December 6, 2007 11:25 AM Adjusting the Gamma Setting You can select from 5 gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to blur the bright areas. Higher values will darken the light areas. 1. Press the Gamma button. You see the following displayed on the screen: 2.
PowerLite Cinema Pro 810.book Page 31 Thursday, December 6, 2007 11:25 AM Locking the Projector The projector includes two lock settings to prevent the image from being accidentally changed once it’s adjusted, and to keep children from turning on the projector without adult supervision. To access the lock settings, follow these steps: 1. Press the Menu button on the remote control. 2. Use the menu navigation buttons to open the Settings menu, then open the Operation menu. Menu button 3.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.book Page 33 Thursday, December 6, 2007 11:25 AM Making Detailed Adjustments You can use the projector’s on-screen menus to make detailed adjustments to the image quality—such as the brightness, contrast, sharpness, and color. You can also change the menu display, sleep mode settings, and other projector features. Using the Menu System You can access the menu system either from the remote control or the buttons on the projector’s control panel.
PowerLite Cinema Pro 810.book Page 34 Thursday, December 6, 2007 11:25 AM To display the line menu, press the of the image: Select button. You see a display like this at the bottom Press the u or d button to highlight an option, then press the Press the Menu button to exit the line menu. Select button to select it.
PowerLite Cinema Pro 810.book Page 35 Thursday, December 6, 2007 11:25 AM ■ Navigation Bar Settings > Display > Bar Select whether to display the navigation bar, which tells you which buttons to press to choose settings. Navigation bar ■ Menu Color Settings > Display > Color Select a color scheme for displaying the menus.
PowerLite Cinema Pro 810.book Page 36 Thursday, December 6, 2007 11:25 AM ■ Brightness/Contrast Picture > Input Adjustment > Contrast Note: If you cannot access the Brightness and Contrast settings, highlight Input Adjustment and press the Select button, then choose Brightness/Contrast in the sub-menu. Adjust the brightness so it’s suitable for your viewing conditions. For example, if you’re projecting in a brightly lit room or onto an especially large screen, you may need to increase the brightness.
PowerLite Cinema Pro 810.book Page 37 Thursday, December 6, 2007 11:25 AM ■ DVI-Video Level Image > Advanced > DVI-Video Level Note: This setting can be used only when HDMI is selected as the image source (see page 22). If your video equipment has a DVI port and you’ve connected it to the projector using an HDMI/DVI cable, set the level of the projector to match that of the video equipment. When this setting is turned on, the projector disregards the EPSON Super White setting.
PowerLite Cinema Pro 810.book Page 38 Thursday, December 6, 2007 11:25 AM Color Settings If the image colors don’t look correct, you can adjust them using these settings. Use the first three settings described below to make the most visible changes. If you only need to make slight adjustments, you can fine-tune the picture with the remaining settings. Most color settings are stored separately for each image source and color mode.
PowerLite Cinema Pro 810.book Page 39 Thursday, December 6, 2007 11:25 AM ■ RGB Picture > Color Adjustment > RGB/RGBCMY > RGB Note: If you cannot access the RGB settings, highlight RGB/RGBCMY (the first item in the menu list) and press the Select button, then choose RGB in the sub-menu. Use the RGB settings to fine-tune the color of the image. You can adjust the offset and gain for each signal color (red, green, and blue). Use Offset to adjust darker shades and Gain for the lightest shades.
PowerLite Cinema Pro 810.book Page 40 Thursday, December 6, 2007 11:25 AM Adjustments for Computer Images In addition to the settings described above, you can adjust the Tracking and Sync settings for analog RGB computer images. Normally, these settings are adjusted automatically by the projector. If you notice that the image is blurry or contains dark vertical bands, you may need to adjust the settings yourself.
PowerLite Cinema Pro 810.book Page 41 Thursday, December 6, 2007 11:25 AM Selecting Memory Settings and Resetting the Projector Your projector comes with 9 memory locations for installers to save customized settings, designed to provide the best color quality for each of your video inputs. Selecting Memory Settings You can easily recall the memory settings by using the memory button on the remote control: 1. Press the Memory button on the remote control. 2.
PowerLite Cinema Pro 810.book Page 42 Thursday, December 6, 2007 11:25 AM Deleting Saved Memory Settings You can clear all your memory settings at once. 1. Press the Menu button on the remote control. 2. Open the Memory menu, then select Reset Memory. 3. Press the Select button to delete the memory settings. Resetting the Projector If the image quality isn’t what you expect, one or more settings may be adjusted improperly.
PowerLite Cinema Pro 810.book Page 43 Thursday, December 6, 2007 11:25 AM Customizing Projector Features Use the settings in this section to adjust the image size and position, suppress on-screen text, and select basic setup options. Image Sizing Before adjusting any of these settings, make sure you have already selected an appropriate aspect ratio for the type of picture you’re viewing (see page 26).
PowerLite Cinema Pro 810.book Page 44 Thursday, December 6, 2007 11:25 AM Screen Options ■ Message Settings > Display > Message Turn this setting off if you want to prevent on-screen messages from appearing (such as the no-signal message, or the identifying text that appears when you switch between image sources or color modes).
PowerLite Cinema Pro 810.book Page 45 Thursday, December 6, 2007 11:25 AM Other Setup Options ■ Keystone Settings > Keystone Adjusts the shape of the image, if the left and right sides are not parallel after tilting the projector up or down at the screen (see page 25). ■ Projection Settings > Projection Inverts the image for overhead projection.
PowerLite Cinema Pro 810.book Page 46 Thursday, December 6, 2007 11:25 AM ■ Sleep Mode Settings > Operation > Sleep Mode Turn off this setting if you don’t want the projector to enter sleep mode. (Sleep mode shuts the projector off automatically when there is no video signal.) Select 30 min., 10 min., or 5 min. as the length of time before shutoff; decreasing the time conserves power and extends the life of the lamp.
PowerLite Cinema Pro 810.book Page 47 Thursday, December 6, 2007 11:25 AM Maintenance Your projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. You also may need to clean the air filter to prevent overheating. Warning: Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely.
PowerLite Cinema Pro 810.book Page 48 Thursday, December 6, 2007 11:25 AM Cleaning the Projector Case Before you clean the case, turn off the projector and unplug the power cord. ■ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth. ■ To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the case and dry it with a dry cloth. Caution: Never use wax, alcohol, benzene, thinner, or other chemical detergents. These can damage the case.
PowerLite Cinema Pro 810.book Page 49 Thursday, December 6, 2007 11:25 AM 5. If you need to replace the filter, release the tab and lift up the cover. 6. Remove the old filter and replace it with a new one. 7. To replace the cover, insert the tabs and press down until the cover clicks into place.
PowerLite Cinema Pro 810.book Page 50 Thursday, December 6, 2007 11:25 AM Replacing the Lamp The projection lamp lasts for up to 3000 hours. You can use the Info menu to check how long it’s been in use (see page 53). It’s time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate. ■ The projector’s warning light flashes red at half-second intervals. ■ The message Replace the lamp appears on the screen when you start projecting.
PowerLite Cinema Pro 810.book Page 51 Thursday, December 6, 2007 11:25 AM 5. Press in the latches securing the lamp cover and lift off the cover. 6. Loosen the two screws securing the lamp (they don’t come all the way out). 7. Grasp the lamp as shown and pull it straight out. Warning: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
PowerLite Cinema Pro 810.book Page 52 Thursday, December 6, 2007 11:25 AM 8. Gently insert the new lamp and tighten its screws. Caution: Don’t touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 9. Replace the lamp cover. (The projector won’t work if the lamp cover is open or loose.) 10. Reset the lamp usage timer, as described below.
PowerLite Cinema Pro 810.book Page 53 Thursday, December 6, 2007 11:25 AM Checking the Projector Status You can use the Info menu to view information about the current display settings and how long the projection lamp has been in use. To access the Info menu: 1. Press the Menu button on the projector or remote control. 2. Use the menu navigation buttons to open the Info menu.
PowerLite Cinema Pro 810.book Page 54 Thursday, December 6, 2007 11:25 AM Transporting the Projector Note: Epson shall not be liable for any damages incurred during transportation. The projector contains many glass and precision parts. When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials. Be sure the carrier is capable of transporting fragile equipment and is aware that the projector is fragile.
PowerLite Cinema Pro 810.book Page 55 Thursday, December 6, 2007 11:25 AM Problem Solving This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support. What To Do When the Lights Come On or Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.
PowerLite Cinema Pro 810.book Page 56 Thursday, December 6, 2007 11:25 AM Light state Warning light is red Cause and solution The projector is too hot, which turns off the lamp automatically. Let it cool for five minutes, then turn it back on. Make sure there is plenty of space around and under the projector for ventilation. Also, clean or replace the filter if necessary (see page 48).
PowerLite Cinema Pro 810.book Page 57 Thursday, December 6, 2007 11:25 AM You’re using a computer and no picture appears on the screen. If you’re using a PC laptop: ■ Press the function key that lets you display on an external monitor. It’s often labeled with an icon such as , but it may also be labeled CRT/LCD. You may have to hold down the Fn key while pressing it. Check your laptop’s manual or online help.
PowerLite Cinema Pro 810.book Page 58 Thursday, December 6, 2007 11:25 AM The picture is upside-down or reversed. Change the Projection setting in the Settings menu (see page 45). Only part of the picture is displayed, or the picture is distorted. ■ Press the Aspect button to select a different aspect ratio (see page 26). ■ If the Aspect is set to Zoom, you may need to use the Zoom Caption option to see the top or bottom section of the screen so that subtitles are visible (see page 43).
PowerLite Cinema Pro 810.book Page 59 Thursday, December 6, 2007 11:25 AM The picture is blurry. ■ Make sure the Input Signal is set correctly for your video equipment (see page 45). ■ There may be dirt on the lens. Clean the lens as described on page 47. ■ Adjust the focus (see page 26). ■ Make sure the lens is not fogged by condensation. If you’ve just moved the projector from a cold environment, wait a couple of minutes before using it. ■ Adjust the Sharpness setting (see page 37).
PowerLite Cinema Pro 810.book Page 60 Thursday, December 6, 2007 11:25 AM Where To Get Help Internet Support Epson provides technical assistance 24 hours a day at epson.com/support. Here you can access troubleshooting information, download product documentation, and receive technical advice through e-mail. Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card that came with your projector.
PowerLite Cinema Pro 810.book Page 61 Thursday, December 6, 2007 11:25 AM Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels 0.7 inch (18 mm) wide Lens F=2.0 to 3.15 Resolution (native format) 1280 × 720 pixels, 720p Brightness 1600 ANSI lumens maximum Dynamic contrast ratio 10000:1 Image size 30 to 300 inches Projection distance 3.0 to 66.8 feet (0.93 to 20.35 m) at 16:9 3.7 to 81.7 feet (1.13 to 24.90 m) at 4:3 Zoom ratio 1-2.
PowerLite Cinema Pro 810.book Page 62 Thursday, December 6, 2007 11:25 AM Dimensions Height 4.9 inches (124 mm); not including adjustable feet Width 16 inches (406 mm) Depth 12.2 inches (309 mm); not including lens protrusion Weight 11.9 lb. (5.4 g) Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC, 2.7 A 200 to 240 VAC, 1.
PowerLite Cinema Pro 810.book Page 63 Thursday, December 6, 2007 11:25 AM Compatible Video Formats The projector supports analog video in NTSC, PAL, and SECAM formats, and it automatically adjusts to the incoming signal. It can receive these formats as composite video, S-video, or component video— which it accepts through the Video, S-Video, and Component ports, respectively. The projector also supports digital video (SDTV, HDTV) and various monitor display formats.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.book Page 65 Thursday, December 6, 2007 11:25 AM ESC/VP21 Command Codes You can use an AV controller with a 9-pin null modem serial cable to control the projector. You can download the complete ESC/VP 21 Communication Manual for home theater projectors from the Epson website at http://support.epson.com.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.book Page 67 Thursday, December 6, 2007 11:25 AM Notices Important Safety Information Follow these safety instructions when setting up and using the projector: ■ Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. ■ Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.
PowerLite Cinema Pro 810.book Page 68 Thursday, December 6, 2007 11:25 AM ■ The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. ■ Allow the lamp to cool for one hour before replacing it. ■ Unplug the projector during lightning storms or when not in use for extended periods. ■ Don’t place the projector or remote control on top of heat-producing equipment.
PowerLite Cinema Pro 810.book Page 69 Thursday, December 6, 2007 11:25 AM FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PowerLite Cinema Pro 810.book Page 70 Thursday, December 6, 2007 11:25 AM Declaration of Conformity According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: Epson America, Inc.
PowerLite Cinema Pro 810.book Page 71 Thursday, December 6, 2007 11:25 AM Epson America, Inc., Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc.
PowerLite Cinema Pro 810.book Page 72 Thursday, December 6, 2007 11:25 AM COVERED BY THIS LIMITED WARRANTY. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY.
PowerLite Cinema Pro 810.book Page 73 Thursday, December 6, 2007 11:25 AM Index A Abs. Color Temp.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.
PowerLite Cinema Pro 810.
